Consulta de temas

Procedure To Set S50N/V To Factory Default Configuration


To reset the S50 to factory defaults, complete the following instructions.
  1. Connect to S50N/V device via console
    • Baud rate = 9600
    • Character Size = 8
    • Flow Control = Disabled
    • Stop Bits = 1
    • Parity = none​
  2. Power cycle the S50 either by disconnecting and reconnecting the power cord, or by typing reload, and then yes at privelidged exec mode
    • FTOS#reload
  3. Hit any key when prompted during the S50 boot process to get into BOOT_USER mode
U-Boot 1.1.4 (F10 Development) (Oct 6 2009 - 03:14:26)
Built by build at hydrogen on Tue Oct 6 3:14:25 2009
S-Series Boot selector Label 2.8.2.0

CPU: 8541, Version: 1.1, (0x807a0011)
Core: E500, Version: 2.0, (0x80200020)
Clock Configuration:
CPU: 660 MHz, CCB: 330 MHz,
DDR: 165 MHz, LBC: 41 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: S50 Force10 Networks
Watchdog enabled
DRAM: Initializing
DDR: 256 MB
Top of RAM usable for U-Boot at: 10000000
Reserving 122k for U-Boot at: 0ffe0000
Reserving 136k for malloc() at: 0ffbe000
Reserving 76 Bytes for Board Info at: 0ffbdfb4
Reserving 72 Bytes for Global Data at: 0ffbdf6c
Stack Pointer at: 0ffbdf48
New Stack Pointer is: 0ffbdf48
Now running in RAM - U-Boot at: 0ffe0000
L2 cache 256KB: enabled
Using default environment

PCI Scan: Found Bus 0, Device 22, Function 0
PCI Scan: Found Bus 0, Device 23, Function 0

In: serial
Out: serial
Err: serial
U-Boot relocated to 0ffe0000
Net: No ethernet found.
### main_loop entered: bootdelay=1

### main_loop: bootcmd="bootm 0xffe80000;setenv verify no;autoscr 0x1700000
bootm fe6000f0"
Hit any key to stop booting: 0
## Booting image at ffe80000 ...
Image Name: netbsd
Image Type: PowerPC NetBSD Standalone Program (uncompressed)
Data Size: 383216 Bytes = 374.2 kB
Load Address: 00040000
Entry Point: 00040004
Verifying Checksum ... OK
Watchdog Disabled
Loading Standalone Application ... OK
Unit 0
Unit 1
Registering ethernet driver for unit 0
Registering ethernet driver for unit 1

None of the boot parameters are configured!!
So Booting from flash!!

You can use U-boot native networking facilities
============================================================



Hit any key to break into BOOT_USER mode: 0 < ------------- hit any key
Starting F10 BLI Shell ...
BOOT_USER #

4. Enter "restore factory-defaults" command at the BOOT_USER prompt

BOOT_USER #restore factory-defaults

Erasing NVRAM contents...
Successfully erased NVRAM contents
Erasing Filesystem sectors...

Successfully erased filesystem sectors
Erasing boot parameters...
Successfully erased boot parameters
Please reload for restore factory-defaults to take effect.

5. Enter "reload" command to execute and the S50N/V system will boot up with factory default configuration (no need to hit any key during this boot up process)

BOOT_USER #reload
!
!
Force10>
Force10>en
Force10#00:07:00: %STKUNIT0-M:CP %SEC-4-ENABLE_PASSW_NOT_CONFIGURED: Enable password is required for authentication but not configured
00:07:00: %STKUNIT0-M:CP %SEC-3-AUTHENTICATION_ENABLE_SUCCESS: Enable password authentication success on console

6.The switch is now factory defaulted and can be configured from here

Force10#config t
Force10(conf)#





Identificación del artículo: HOW10651

Última fecha de modificación: 06/02/2016 10:59 AM


Califique este artículo

Preciso
Útil
Fácil de comprender
¿Este artículo fue útil?
No
Envíenos sus comentarios
Los comentarios no pueden contener estos caracteres especiales: <>"(", ")", "\"
Disculpe, nuestro sistema de comentarios está actualmente inactivo. Vuelva a intentarlo más tarde.

Muchas gracias por sus comentarios.