Base de connaissances

How to Manage QSFP Ports on a N4000 Series Switch


This article explains how to manage the QSFP ports on a N4000 Series switch, including; setting a 1 x 40Gb (gigabit) QSFP port into 4 x 10Gb QSFP ports, setting the 4 x 10Gb QSFP ports to a 1 x 40Gb QSFP port, verifying the 1 x 40Gb and 4 x 10Gb ports are available and configuring a QSFP port as stack ports.





The default setting for a forty gigabit QSFP port (1 x 40Gb) and its' respective ten gigabit (4 x 10Gb) breakout ports is Ethernet, nonstacking.
When changing from one mode to another, a switch reboot is required. Consider updating the firmware.

To break out a 1 x 40Gb QSFP port on a N4000 Series switch into 4 x 10Gb ports, do the following:

The appropriate quad-breakout/QBO cable (fan out cable) must be used.
On a N4032 and N4032F, the QSFP plug in module ports are named Fo1/1/1-2 in 40-gigabit mode and Te1/1/1-8 in 10-gigabit mode.
On a N4064 and N4064F, the fixed QSFP ports are named Fo1/0/1-2 in 40-gigabit mode and Te1/0/49-56 in 10-gigabit mode. The ports on an optional QSFP plug-in module are named Fo1/1/1-2 in 40-gigabit mode and Te1/1/1-8 in 10-gigabit mode.

1. Configure the QSFP port to be broken out.

console>enable

console#configure

console(config)#interface Fo1/1/1

console(config-if-Fo1/1/1)#hardware profile portmode 4x10g

2. Reboot the switch to transition the port into 4x10g mode.

This command will not take effect until the switch is rebooted.

console(config-if-Fo1/1/1)#do reload

Are you sure you want to reload the stack? (y/n)

3. Verify the 4 x 10Gb ports are available.

console>enable

console#show interfaces status

The reconfigured forty gigabit port's Link State should change to "Detached".
The respective ten gigabit ports' Link State should change from "Detached" to "Up" or "Down".

To change the 4 x 10Gb QSFP ports on a N4000 Series switch to a 1 x 40Gb QSFP port, do the following:

1. Configure the port.

console>enable

console#configure

console(config)#interface Fo1/1/1

console(config-if-Fo1/1/1)#hardware profile portmode 1x40g

2. Reboot the switch to transition the port into 1x40g mode.

This command will not take effect until the switch is rebooted.

console(config-if-Fo1/1/1)#do reload

Are you sure you want to reload the stack? (y/n)

3. Verify the 1 x 40Gb port is available.

console>enable

console#show interfaces status

The four reconfigured ten gigabit ports' Link State should change to "Detached".
The respective forty gigabit port's Link State should change from "Detached" to "Up" or "Down".

To configure a QSFP port as a stack-port on a N4000 Series switch, do the following:

QSFP ports support stacking over the interfaces in either 1x40g mode or 4x10g mode. The QSFP port must be configured into 4 x 10g mode prior to configuring the respective ten gigabit ports into stack mode.

N4000 Series switches support stacking over Ethernet ports as well.

1. Configure the desired QSFP port from the default Ethernet mode to stack mode.

console>enable

console#config

console(config)#stack

console(config-stack)#stack-port fortygigabitethernet 1/1/1 stack

2. Reboot the switch to transition the port into stack mode.

console(config-if-Fo1/1/1)#do reload

Are you sure you want to reload the stack? (y/n)

3. Verify the 1 x 40Gb port or 4 x10Gb ports are in stack mode.

console>enable

console#show switch stack-ports


ID de l'article : HOW10476

Date de la dernière modification : 06/02/2016 01:10 PM


Noter cet article

Précis
Utile
Facile à comprendre
Avez-vous trouvé cet article utile ?
Oui Non
Envoyez-nous vos commentaires
Les commentaires ne doivent pas contenir les caractères spéciaux : <>()\
Désolé, notre système de collecte des commentaires est actuellement indisponible. Veuillez réessayer ultérieurement.

Merci pour vos commentaires.