知識庫

OptiPlex 960 Small Form Factor ( SFF) Removal Guide for the System Cover, Optical Drive, Media Bay Drive, Hard Drive and 25 Hard Drive


Article Summary: This article provides information on removing components from a OptiPlex 960 Small Form Factor.


Table of Contents:
  1. System Cover Removal
  2. Optical Drive Removal
  3. Media Bay Drive Removal
  4. Hard Drive Removal
  5. 2.5" Hard Drive Removal




1.


System Cover Removal



1. Pre-Removal Instructions Before removing the First Removal:
  • During installation or removal of any hardware always ensure all data is backed up properly

  • Disconnect any telephone, network, or USB cables from the computer

  • Disconnect the computer and all attached devices from their electrical outlets


2. Establishing image.



3. Slide back the cover release latch.



4. Tilt the system cover from the top outward.



5. Remove the system cover.



6. Complete.



Back to Top




2.


Optical Drive Removal



1. Pre-Removal Instructions Before removing the Second Removal:
  • During installation or removal of any hardware always ensure all data is backed up properly

  • Disconnect any telephone, network, or USB cables from the computer

  • Disconnect the computer and all attached devices from their electrical outlets

  • Remove the system cover


2. Establishing image.



3. Disconnect the power cable from the optical drive.



4. Disconnect the SATA cable from the optical drive.



5. Push down on the drive release latch.



6. Slide the optical drive toward the back of the system.



7. Lift the back edge of the optical drive up.



8. Slide the optical drive out of the system.



9. Complete.




Back to Top




3.


Media Bay Drive Removal



1. Pre-Removal Instructions Before removing the Third Removal:
  • During installation or removal of any hardware always ensure all data is backed up properly

  • Disconnect any telephone, network, or USB cables from the computer

  • Disconnect the computer and all attached devices from their electrical outlets

  • Remove the system cover and optical drive


2. Establishing image.



3. Disconnect the data cable from the media bay drive.



4. Press down on the drive release latch.



5. Slide the drive toward the back of the system.



6. Lift the edge of the drive that is closest to the center of the system up.



7. Slide the drive toward the center of the system.



8. Lift the back edge of the drive.



9. Rotate the drive around to free it of the guide rails.



10. Remove the media bay drive from the system.



11. Complete.




Back to Top




4.


Hard Drive Removal



1. Pre-Removal Instructions Before removing the Fourth Removal:
  • During installation or removal of any hardware always ensure all data is backed up properly

  • Disconnect any telephone, network, or USB cables from the computer

  • Disconnect the computer and all attached devices from their electrical outlets

  • Remove the system cover


2. Establishing image.



3. Press the hard drive carrier release latches.



4. Rotate the hard drive carrier up.



5. Slide the hard drive carrier toward the front of the system.



6. Turn the hard drive carrier over.



7. Disconnect the power cable from the hard drive.



8. Disconnect the SATA cable from the hard drive.



9. Remove the SATA cable from its routing on the hard drive carrier.



10. Remove the hard drive carrier from the system.



11. Gently pry the two hard drive release tabs away.



12. Lift the hard drive carrier away from the hard drive and remove.



13. Complete.




Back to Top




5.


2.5"Hard Drive Removal



1. Pre-Removal Instructions Before removing the Fifth Removal:
  • During installation or removal of any hardware always ensure all data is backed up properly

  • Disconnect any telephone, network, or USB cables from the computer

  • Disconnect the computer and all attached devices from their electrical outlets

  • Remove the system cover and hard drive


2. Establishing image.



3. Disconnect the power cable from the primary hard drive



4. Disconnect the power cable from the secondary hard drive



5. Remove the power cable.



6. Disconnect the data cable from the primary hard drive.



7. Disconnect the data cable from the secondary hard drive.



8. Remove the four screws from the primary hard drive.



9. Remove the primary hard drive.



10. Flip the hard drive carrier over.



11. Remove the four screws from the secondary hard drive.



12. Remove the secondary hard drive.



13. Complete.




Return to the Optiplex 960 Teardown/Removal Index.


Back to Top


If you require further assistance or wish to give us feedback, please engage our technical team on Twitter.

 


Quick Tips content is self-published by the Dell Support Professionals who resolve issues daily. In order to achieve a speedy publication, Quick Tips may represent only partial solutions or work-arounds that are still in development or pending further proof of successfully resolving an issue. As such Quick Tips have not been reviewed, validated or approved by Dell and should be used with appropriate caution. Dell shall not be liable for any loss, including but not limited to loss of data, loss of profit or loss of revenue, which customers may incur by following any procedure or advice set out in the Quick Tips.

文章 ID: SLN290593

上次修改日期: 06/27/2016 09:03 AM


為本文評分

準確
實用
易懂
這篇文章對您有用嗎?
傳送意見反應
評語中不得包含下列特殊字元:<>()\
很抱歉,我們的意見回饋系統目前關閉中。請稍後再試。

感謝您的寶貴意見。