Consulta de temas

How to discover and monitor EqualLogic using OME 2.0




Table of Contents:

  1. Environment
  2. Configuring EQL
  3. Configuring OME
  4. Confirm the Result

This article provides information on how to discover and monitor EqualLogic (EQL) using Dell OpenManage Essentials (OME).


Environment:

Target EQL

  • Product Name: PS6010
  • Group Name: ELSTest-01 
  • Member Name: PS6010-01
  • Firmware: 7.0.10
  • Management IP Address: 10.30.99.30/16
  • Management Port IP Address: 10.30.99.31/16

Host to be installed OME

  • OS: Windows Server 2012 R2 Standard Edition
  • IP Address: 10.30.100.245/16
  • Installed SNMP Service

Step 1: Configuring EQL

  1. Launch and login Group Manager (Figure 1).

    Figure 1: Group Manager login
  2. In left pane, click Group Configuration in the group tree (Figure 2).

    Figure 2: Group Configuration
  3. Click the SNMP tab under Group Configuration (Figure 3).

    Figure 3: Group Configuration
  4. Click Add in Read-only community names under Access (Figure 4).

    Figure 4: Read-only Community Names
  5. Enter community name and click OK (Figure 5).
    <Insert Pic 1-5>
    Figure 5: Read-only Community Name
  6. Click Add in Trap destinations under Traps (Figure 6).

    Figure 6: Trap Destinations
  7. Enter the IP address of the trap destination and click OK (Figure 7).

    Figure 7: Trap Desination IP Address
  8. Enter community name in Trap community name (Figure 8).

    Figure 8: Trap Community Name
  9. Click the Save all changes icon (Figure 9).

    Figure 9: Save All Changes

Step 2: Configuring OME

1. Launch OME (Figure 10).

Figure 10: OpenManage Essentials Home Portal

2. Click the Manage tab then click Discovery and Inventory (Figure 11).

Figure 11: Manage / All Devices

3. Click Add Discovery Range under Common Tasks (Figure 12).

Figure 12: Discovery and Inventory Portal

4.Enter Management IP address and Management Port IP address of EQL, then click Add (Figure 13).
If you don’t configure Management Port, enter Group IP address and each port IP addresses instead of Management IP address.

Figure 13: Specify IP Address, Range, or Host Name

5.In left pane, click SNMP Configuration (Figure 14).
Click the Enable SNMP discovery checkbox and enter community name.

Figure 14: Discovery Range Configuration / SNMP Configuration

6. In left pane, click Discovery Range Action (Figure 15).
Choose Perform both discovery and inventory then click Finish.

Figure 15: Discovery Range Action

7. Wait until Task State changes to Complete (Figure 16).

Figure 16: Discovery Range Summary


Step 3: Confirm the Result

Now you can see EQL is discovered and inventoried in OME. (Figure 17).


Figure 17: Device Summary



Quick Tips content is self-published by the Dell Support Professionals who resolve issues daily. In order to achieve a speedy publication, Quick Tips may represent only partial solutions or work-arounds that are still in development or pending further proof of successfully resolving an issue. As such Quick Tips have not been reviewed, validated or approved by Dell and should be used with appropriate caution. Dell shall not be liable for any loss, including but not limited to loss of data, loss of profit or loss of revenue, which customers may incur by following any procedure or advice set out in the Quick Tips.

Identificación del artículo: SLN294909

Última fecha de modificación: 12/05/2014 12:44 PM


Califique este artículo

Preciso
Útil
Fácil de comprender
¿Este artículo fue útil?
No
Envíenos sus comentarios
Los comentarios muestran caracteres no válidos, los caracteres especiales que no se aceptan son <> () &#92;
Disculpe, nuestro sistema de comentarios está actualmente inactivo. Vuelva a intentarlo más tarde.

Gracias. Sus comentarios se han enviado.