Transparently connect Dell™ M-Series blade servers into the LAN of your choice.
Connecting to XAUI-based 10GbE mezzanine cards (10Gb Ethernet Pass-Through II) and KR-based 10GbE mezzanine cards and NDCs (10Gb Ethernet Pass-Through-k).
32 total Ethernet ports: 16 internal (server) ports and 16 external (LAN) ports
1:1 Internal-external port pairs provide dedicated connections for isolated bandwidth between server and LAN
Ships with all 32-ports enabled
All external ports are hot-pluggable, enabling expansion without server interruption
All ports enabled standard
External ports also support 10Gb SFP+ LR optics and SFP+ Direct-Attach (copper) cables (0.5m, 1m, 3m, 5m, 7m)
Supported Adapters (by model):Adapter (NIC/CNA) support varies based on model of Pass Through
Dell 10Gb Ethernet Pass Through II supports the following XAUI-based adapters:
Broadcom 57710 mezzanine card
Broadcom 57711 mezzanine card
Intel X520 mezzanine card
Intel X520-x/k mezzanine card
QLogic QME8142 mezzanine card
Emulex OCm10102-f-m mezzanine card
Dell 10Gb Ethernet Pass Through-k supports the following KR-based adapters:
Brocade BR1741M-k mezzanine card
Broadcom 57712-k network daughter card (NDC)
Intel X520-x/k mezzanine card
Future 10Gb adapters for PowerEdge blade servers
Note: 1Gb NICs are not supported with either model of pass-through
- 10 Gigabit per second line speed per port, full duplex
- Connects Dell blade servers using 10 Gigabit Ethernet NIC blade mezzanine I/O cards to external switches
Great solution for Dell™ PowerConnect™, Cisco Catalyst/Nexus switches as well as your choice of external Ethernet switches
Dell 10Gb Ethernet Pass Through Modules are transparent to all Ethernet topologies, providing connectivity from Dell blades to any vendor’s external LAN switch.
Connect to any industry standard Ethernet compliant device.
- Module is unmanaged – all management occurs via NIC firmware or O/S, or external switch Device status is available through the M1000e Chassis Management Controller (CMC)
Dell 10GbE-k Pass-Through Module performs a power on self-test and various ongoing diagnostics to ensure proper operation
Single-wide I/O Module for M1000e (Width: 272.75 mm, Height: 32.48 mm, Depth: 307.24 mm)
2.6 kg without SFP’s; 3.0 kg with SFP’s
10GbE SFP+ Optical Transceiver, SR, LC Connector
10GbE SFP+ Optical Transceiver, LRM, LC Connector
1m SFP+ Direct Attach Cable Transceiver Assembly
3m SFP+ Direct Attach Cable Transceiver Assembly
5m SFP+ Direct Attach Cable Transceiver Assembly
7m SFP+ Direct Attach Cable Transceiver Assembly
Environmental Operating Conditions
- Please see limits associated with M1000e blade enclosure
- DC Input:
2V from shared power supplies in M1000e blade enclosure
Approximately 20 Watts without SFP’s
Approximately 28 Watts with SFP’s
|Interoperability without consideration|
Dell 10GbE Pass-Through Modules ensure 10Gb Ethernet interoperability for M-Series blade deployments. Since pass throughs are transparent devices, they are unseen in LAN topologies and provide direct Ethernet connectivity from server blades to external LANs. This level of interoperability can be beneficial when seeking to integrate blade servers into existing LANs from any partner of your choice.
Plug and done
As unmanaged devices, Dell 10Gb Ethernet Pass-Through Modules require no setup, configuration or management. Simply plug the unit into the M1000e chassis and connect cables to the sixteen optional shortwave SFP+ optical transceivers, and you’re done. The modules automatically connect at 10 Gbps on a port-by-port basis, enabling traffic to begin flowing from server blade to external 10Gb network switch.