기술 문서

OptiPlex 9010 All in One (AIO) Removal Guide for the Vesa Cover, System Stand, Rear Cover, Memory and Optical Drive



This article provides information on removing components from a OptiPlex 9010 All-In-One.


Table of Contents:

  1. Vesa Cover Removal
  2. System Stand Removal
  3. Rear Cover Removal
  4. Memory Removal
  5. Optical Drive Removal

1. Vesa Cover Removal

1. Pre-Removal Instructions Before removing the Vesa Cover Removal:

  • During installation or removal of any hardware always ensure all data is backed up properly
  • Disconnect any telephone, network, or USB cables from the computer
  • Disconnect the computer and all attached devices from their electrical outlets

2. Establishing image.



3. Gently push the cover to open the vesa cover.



4. Remove the cover.



5. Complete.




Back to Top


2. System Stand Removal

1. Pre-Removal Instructions Before removing the System Stand Removal:

  • During installation or removal of any hardware always ensure all data is backed up properly
  • Disconnect any telephone, network, or USB cables from the computer
  • Disconnect the computer and all attached devices from their electrical outlets
  • Remove the Vesa Cover

2. Establishing image.



3. Use a Phillips head screwdriver to remove the four (4) screws securing the stand to the system.



4. Remove the stand.



5. Complete.




Back to Top


3. Rear Cover Removal

1. Pre-Removal Instructions Before removing the Rear Cover Removal:

  • During installation or removal of any hardware always ensure all data is backed up properly
  • Disconnect any telephone, network, or USB cables from the computer
  • Disconnect the computer and all attached devices from their electrical outlets
  • Remove the Vesa Cover and System Stand

2. Establishing image.



3. Use a Phillips head screwdriver to remove the four (4) screws securing the rear cover from the system.



4. On the back panel of system, there are 2 holes where u can insert your finger to gently push out the rear cover from the system.



5. Complete.




Back to Top


4. Memory Removal

1. Pre-Removal Instructions Before removing the Memory Removal:

  • During installation or removal of any hardware always ensure all data is backed up properly
  • Disconnect any telephone, network, or USB cables from the computer
  • Disconnect the computer and all attached devices from their electrical outlets
  • Remove the Vesa Cover, System Stand and Rear Cover

2. Establishing image.



3. Gently remove out the memory cover.



4. Pull the pin outwards to release the memory.



5. Pull out the memory.



6. Repeat step 2 to 3 for the next memory.



7. Complete.




Back to Top


5. Optical Drive Removal

1. Pre-Removal Instructions Before removing the Optical Drive Removal:

  • During installation or removal of any hardware always ensure all data is backed up properly
  • Disconnect any telephone, network, or USB cables from the computer
  • Disconnect the computer and all attached devices from their electrical outlets
  • Remove the Vesa Cover, System Stand and Rear Cover

2. Establishing image.



3. Remove 2 screws on the ODD bracket



4. Gently lift up the ODD (1) and remove the cables (2).



5. Complete.


Back to Top





문서 ID: SLN295882

최종 수정일: 05/17/2017 10:50 AM


이 문서 평가하기

정확함
유용함
이해하기 쉬운
이 문서가 도움이 되셨나요?
지원 미지원
피드백을 보내 주십시오.
의견에는 <>()\와 같은 특수 문자를 사용할 수 없습니다.
죄송합니다. 현재 피드백 시스템은 사용하실 수 없습니다. 잠시 후에 다시 시도하십시오.

피드백을 보내주셔서 감사합니다.