Base de conhecimento

How to Clear the CMOS of a Sentia 223 or 3200 Mobile System? - KB Article - 349717




Article Summary: How to Clear the CMOS of a Sentia 223 or 3200 Mobile System?

Article Summary: This article describes to clear the CMOS of a Sentia 223 or 3200 mobile system.

Steps to Clear the CMOS of a Sentia 223 or 3200 Mobile System

Caution:
Before performing any of the procedures in this section, read and follow the safety instructions in Dell Knowledge Base Article: "Precautionary Measures for Personal Safety" Article ID: 339031.

Caution:
A new battery can explode if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by Alienware. Properly dispose of used batteries are required as per the local authorities.

The procedure below works on this computer model because of the particular design on the CMOS battery base.

Note:
Never invert the polarity of the batteries of any other device unless otherwise specified by the manufacturer.
  1. Turn off the computer.
  2. Unplug the AC adapter.
  3. Remove the main battery and the secondary battery (if present).
  4. Flip the computer upside down, remove the 2 screws from the memory and Mini PCI cover, and then remove the cover (Figure 1).


    Figure 1: Screws from the Memory and Mini PCI Cover (Click to Enlarge the Image)
  5. In case of an internal wireless card installed, it is necessary to remove it in order to make the CMOS battery visible. For more information about the Sentia 223 or 3200 mobile system Mini PCI card removal, refer the Dell Knowledge Base article, ÃÂHow to Reseat or Replace a Mini PCI Card on a Sentia 223 or m3200 Mobile System?ÃÂ Article ID: 349720.
  6. Note the position of the CMOS battery (Figure 2), the positive end (+) is always facing you.


    Figure 2: Sentia 223 or 3200 CMOS Battery (Click to Enlarge the Image)
  7. Use the fingers, flip up and remove the CMOS battery. Install it upside down. This is, with the positive end (+) facing the computer.
    Note:
    The design of the CMOS battery base of this computer ensures that if the battery is in the inverted position, it will not deliver any voltage to the motherboard. Instead, both contacts of the battery base will only touch the positive side of the battery, thus there is no voltage applied to the board. The positive end of the battery behaves as a bridge that allows the CMOS to discharge itself safely just as the Clear CMOS jumper does on a desktop motherboard.
  8. Wait at least 10 seconds.
  9. Remove the battery, and reinstall it in its normal position.
  10. Assemble the computer, install the battery, AC adapter, and turn on the computer again.
  11. A checksum error may occur. Go to the BIOS setup to load the defaults, and then press <F10> to save changes and exit.




Quick Tips content is self-published by the Dell Support Professionals who resolve issues daily. In order to achieve a speedy publication, Quick Tips may represent only partial solutions or work-arounds that are still in development or pending further proof of successfully resolving an issue. As such Quick Tips have not been reviewed, validated or approved by Dell and should be used with appropriate caution. Dell shall not be liable for any loss, including but not limited to loss of data, loss of profit or loss of revenue, which customers may incur by following any procedure or advice set out in the Quick Tips.

ID do artigo: SLN60435

Data da última modificação: 09/22/2017 04:51 PM


Rate this article

Preciso
Úteis
Fácil de entender
Este artigo foi útil?
Sim Não
Envie seus comentários
Os comentários não podem conter estes caracteres especiais: <>()\
Infelizmente, o nosso sistema de feedback está atualmente desativado. Tente novamente mais tarde.

Agradecemos o feedback.