知識庫

How to Install the Optional 550-Sheet Feeder on the C2665dnf Dell Laser Printer


Table of Contents:

  1. Installing The Optional 550-Sheet Feeder
  2. Updating Your Driver to Detect 550-Sheet Feeder

This article provides information on "How to Install the Optional 550-Sheet Feeder on the C2665dnf Dell Laser Printer"


1. Installing The Optional 550-Sheet Feeder

WARNING: If you install the optional 550-sheet feeder after setting up the printer, be sure to turn off the printer, unplug the power cable, and disconnect all cables from the back of the printer before starting this task.
  1. Ensure that the printer is turned off, and then disconnect all cables from the back of the printer.
  2. Remove the tape and the bag holding the screws.
  3. Place the optional 550-sheet feeder in the same location that the printer is located.
  4. Pull Tray 1 out of the printer about 200mm.

  5. Hold Tray 1 with both hands, and remove it from the printer.

  6. Lift the printer and align the five guide pins of the optional 550-sheet feeder with the holes at the bottom of the printer. Gently lower the printer onto the optional 550-sheet feeder.
    WARNING: Two people are required to lift the printer
    Be careful not to pinch your fingers when lowering the printer onto the optional 550-sheet feeder.



  7. Secure the optional 550-sheet feeder to the printer by tightening the two screws provided with the feeder, using a coin or similar object.

  8. Insert tray 1 into the printer, and push until it stops.

  9. Re-connect all cables into the back of the printer, and turn on the printer.
    Note: A note indicates important information that helps you make better use of your computer system.
  10. Print the system settings report to confirm that the optional 550-sheet feeder is installed correctly.
  11. Confirm Tray 2 (550 Sheet Feeder) is listed in the system settings report under Print Options.
    If the feeder is not listed, turn off the printer, unplug the power cable, and re-install the optional 550-sheet feeder.
  12. After loading paper in the optional 550-sheet feeder, specify the paper type from the printer touch panel.
    • Press the Information button.
    • Tap the Tools tab, and then tap Tray Management.
    • Tap Tray Settings.
    • Tap Tray 2.
    • Tap Type.
    • Tap Down until the desired paper type appears, and then tap the desired paper type.
    • Tap OK.
  13. If you installed the optional 550-sheet feeder after installing the printer driver, update your driver by following the instructions for each operating system. If the printer is on a network, update the driver for each client.

More info can be found in the C2665dnf User’s Guide.

Back to Top

2. Updating Your Driver to Detect 550-Sheet Feeder

When Using PCL Driver

Windows 8
Windows 8 x64
Windows Servicer 2012
  1. Under Desktop mode, right-click the bottom left corner of the screen, and then click Control Panel → Hardware and Sound (Hardware for Windows Server 2012) → Devices and Printers.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Printer properties.
  3. Click the Configuration tab, and then select Bi-Directional Setup.
  4. Select Get Information from Printer and then click OK.
  5. Click Apply, and then click OK.
  6. Close the Devices and Printers dialog box.
Windows 7
Windows 7 x64
Server 2008 R2 x64
  1. Click Start → Devices and Printers.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Printer properties.
  3. Click the Configuration tab, and then select Bi-Directional Setup.
  4. Select Get Information from Printer and then click OK.
  5. Click Apply, and then click OK.
  6. Close the Devices and Printers dialog box.
Windows Vista
Windows Vista x64
  1. Click Start → Control Panel → Hardware and Sound → Printers.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Properties.
  3. Click the Configuration tab, and then select Bi-Directional Setup.
  4. Select Get Information from Printer and then click OK.
  5. Click Apply, and then click OK.
  6. Close the Printers dialog box.
Windows Server 2008
Server 2008 x64
  1. Click Start → Control Panel → Printers.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Properties.
  3. Click the Configuration tab, and then select Bi-Directional Setup.
  4. Select Get Information from Printer and then click OK.
  5. Click Apply, and then click OK.
  6. Close the Printers dialog box.
Windows XP
Windows XP x64
Server 2003
Server 2003 x64
  1. Click start → Printers and Faxes.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Properties.
  3. Click the Configuration tab, and then select Bi-Directional Setup.
  4. Select Get Information from Printer and then click OK.
  5. Click Apply, and then click OK.
  6. Close the Printers dialog box.

If the printer information is not updated automatically after clicking Get Information from Printer, follow these steps:

  1. Click the Options tab, and then select Paper Tray Configuration in the Items list box.
  2. Select Tray2 in the Paper Tray Configuration drop-down menu in Change Setting for.
  3. Click Apply, and then click OK.
  4. Close the Printers and Faxes(Printers, or Devices and Printers) dialog box.

When Using PS Driver

Windows 8
Windows 8 x64
Windows Servicer 2012
  1. Under Desktop mode, right-click the bottom left corner of the screen, and then click Control Panel → Hardware and Sound (Hardware for Windows Server 2012) →Devices and Printers.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Printer properties.
  3. Click the Configuration tab, and then select Bi-Directional Setup.
  4. Select Get Information from Printer and then click OK.
  5. Click Apply, and then click OK.
  6. Close the Devices and Printers dialog box.
Windows 7
Windows 7 x64
Server 2008 R2 x64
  1. Click Start → Devices and Printers.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Printer properties.
  3. Click the Configuration tab, and then select Bi-Directional Setup.
  4. Select Get Information from Printer and then click OK.
  5. Click Apply, and then click OK.
  6. Close the Devices and Printers dialog box.
Windows Vista
Windows Vista x64
  1. Click Start → Control Panel → Hardware and Sound → Printers.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Properties.
  3. Click the Configuration tab, and then select Bi-Directional Setup.
  4. Select Get Information from Printer and then click OK.
  5. Click Apply, and then click OK.
  6. Close the Printers dialog box.
Windows Server 2008
Server 2008 x64
  1. Click Start → Control Panel → Printers.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Properties.
  3. Click the Configuration tab, and then select Bi-Directional Setup.
  4. Select Get Information from Printer and then click OK.
  5. Click Apply, and then click OK.
  6. Close the Printers dialog box.
Windows XP
Windows XP x64
Server 2003
Server 2003 x64
  1. Click Start → Printers and Faxes.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Properties.
  3. Click the Configuration tab, and then select Bi-Directional Setup.
  4. Select Get Information from Printer and then click OK.
  5. Click Apply, and then click OK.
  6. Close the Printers and Faxes dialog box.

If the printer information is not updated automatically after clicking Get Information from Printer, follow these steps:

  1. Click the Configuration tab, and then select Installable Options.
  2. Select Paper Tray Configuration in the Items list box.
  3. Select Tray 2 in the Paper Tray Configuration drop-down menu in Setting for.
  4. Click OK.
  5. Click Apply, and then click OK.
  6. Close the Printers and Faxes (Printers, or Devices and Printers) dialog box.
Mac OS X 10.7.x/10.8.x
  1. Select the Print & Scan in System Preferences.
  2. Select the printer in Printers list, and click Options & Supplies.
  3. Select Driver, select the options that have been installed on the printers, and then click OK.
Mac OS X 10.5.x/10.6.x
  1. Select the Print & Fax in System Preferences.
  2. Select the print in Printers list, and click Options & Supplies.
  3. Select Driver, select the options that have been installed on the printers, and then click OK.

When Using XML Paper Specification (XPS) Driver

Note: The XPS driver does not support Windows XP, XP x64, Windows Server 2003, and Server 2003 x64.
Windows 8
Windows 8 x64
Windows Server 2012
  1. Under Desktop mode, right-click the bottom left corner of the screen, and then click Control Panel → Hardware and Sound (Hardware for Windows Server 2012) → Devices and Printers.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Printer properties.
  3. Click the Device Setting tab, and then select Available in Tray2 drop-down menu.
  4. Click Apply, and then click OK.
  5. Close the Devices and Printers dialog box.
Windows 7
Windows 7 x64
Server 2008 R2 x64
  1. Click Start → Devices and Printers.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Printer properties.
  3. Click the Device Setting tab, and then select Available in Tray2 drop-down menu.
  4. Click Apply, and then click OK.
  5. Close the Devices and Printers dialog box.
Windows Vista
Windows Vista x64
  1. Click Start → Control Panel → Hardware and Sound → Printers.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Properties.
  3. Click the Device Setting tab, and then select Available in Tray2 drop-down menu.
  4. Click Apply, and then click OK.
  5. Close the Printers dialog box.
Windows Server 2008
Server 2008 x64
  1. Click Start → Control Panel → Printers.
  2. Right-click the printer icon of the Dell C2665dnf Color Laser Multifunction Printer, and then select Properties.
  3. Click the Device Setting tab, and then select Available in Tray2 drop-down menu.
  4. Click Apply, and then click OK.
  5. Close the Printers dialog box.

More info can be found in the C2665dnf User’s Guide.

If these steps do not correct the problem, please contact Dell Technical Support.

Back to Top



文章 ID: SLN286290

上次修改日期: 08/03/2015 10:36 AM


為本文評分

準確
實用
易懂
這篇文章對您有用嗎?
傳送意見反應
意見反應中有無效的字元,不接受的特殊字元如下 <> () &#92;
很抱歉,我們的意見回饋系統目前關閉中。請稍後再試。

感謝您。您的意見已送出。