INSTALADO AUTOMATICAMENTEEste arquivo foi instalado automaticamente como parte de uma atualização recente. Se você estiver enfrentando algum problema, poderá fazer download e reinstalar manualmente.
O conteúdo desta página pode ter sido traduzido automaticamente. Para fazer comentários, preencha o formulário no fim da página.
Este arquivo foi instalado automaticamente como parte de uma atualização recente. Se você estiver enfrentando algum problema, poderá fazer download e reinstalar manualmente.
PERC 4/Di Device Driver for Red Hat Linux 7.2.
Recomendado
Encontre a melhor opção de download para seu sistema
Digite os dados do seu produto para ver as informações mais recentes sobre o driver do sistema
Pesquisar no suporte
Digite a etiqueta de serviço ou o modelo da Dell
Quer procurar o seu produto? Digite um identificador do produto.Mostre-me como
Nenhum resultado encontrado. Não foi possível encontrar resultados para a sua pesquisa. Modifique sua pesquisa e tente novamente.
Este driver não é compatível
Este driver não é válido para o produto selecionado. Selecione outro produto para digitar novamente os dados do seu produto para este driver ou acesse a página Suporte a produtos para ver todos os drivers de um produto diferente.
Faça log-in no Windows como administrador para usar a verificação automática. Se você já estiver conectado como administrador e estiver vendo esta mensagem, reinicialize o sistema.O sistema é gerenciado pelo administrador da TI e pode haver poucos recursos.
Encontre mais atualizações. Use o SupportAssist para encontrar as atualizações de driver mais recentes para o seu dispositivo.
A Dell Technologies recomenda analisar esta atualização para determinar se ela é válida para seu sistema. A atualização contém alterações que afetam apenas determinadas configurações ou oferece novos recursos que podem ou não ser válidos para seu ambiente.
Formato do arquivo:Extrai arquivos diretamente no disco local
Nome do arquivo:perc4di-118c-72c.tar.gz
Tamanho do arquivo:538.62 KB
Este é um arquivo pesado. Dependendo da velocidade da sua conexão, o download pode demorar um tempo para ser concluído.
Descrição de formato:
Este formato de arquivo consiste em um conjunto de arquivos que podem ser descompactados para um diretório no disco rígido. A instalação pode ser feita por esse diretório.
Instructions for downloading and creating driver diskette: ----------------------------------------------------------
You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
Download the file PERC4di-118c-72c.tar.gz to a temporary directory on your working system.
Extract the file to the floppy disk as follows:
1. On a Linux system:
Type the following commands under a Linux command shell: mount /dev/fd0 /mnt/floppy tar xvzf -C /mnt/floppy (Eg: /temp/PERC4di-118c-72c.tar.gz) umount /mnt/floppy
2. On a Microsoft Windows system:
You can use Winzip to extract tar.gz archives. However, note the following settings under Winzip to ensure correct extraction of the files.
Start Winzip -> Go to Options -> Configuration
Under the Miscellaneous tab make sure "TAR file smart CR/LF conversion" is unchecked.
Upon opening the tar.gz archive with Winzip, you get the following prompt:
'Archive contains one file. Should Winzip decompress it to a temporary folder and open it?'
Press 'yes' and extract the files normally under Winzip to the floppy drive.
Install Red Hat Linux 7.2 driver for PERC 4/Di as a boot controller -------------------------------------------------------
There are two ways of installing Red Hat 7.2 driver onto the PERC 4/Di as a boot controller. One is using a driver disk during OS installation and the second is using a driver (megaraid) RPM to update driver after OS is installed. The steps for both of these methods are provided below. All the files needed for both methods are included in the driver diskette created above.
For more detailed installation instructions of Red Hat 7.2, please refer to the OS installation guide at http://www.dell.com/linux.
I. Installing driver during OS installation: --------------------------------------------
1. Boot normally from the Redhat installation CD-Rom.
2. Type 'linux dd' on the boot prompt.
3. When the install prompts for a driver disk, insert the driver diskette created above and press 'Enter'.
4. Installation progresses normally. Continue until the 'Create Bootdisk' screen. Press CTRL-ALT-F2 to get to a shell window and type the following commands:
chroot /mnt/sysimage cd /boot /sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10 lilo ( only if lilo was used as bootloader. If grub used - skip this step ) exit
Press CTRL-ALT-F7 to get back to the install screen.
5. Complete the installation as directed by the install.
II. Update driver using RPMs after OS is installed --------------------------------------------------
Type the following commands under a Linux command shell:
mount /dev/fd0 /mnt/floppy cd /mnt/floppy ./megarpmwrapper.sh
Than follow the on-screen instructions to install the RPM driver.
For more detailed information about the script megarpmwrapper.sh, please refer to the release_notes.txt included in the release.