Dell PowerVault 224F/660F SES Firmware, v. 1.9.5, A01
已自动安装 此文件是作为最近更新的一部分自动安装的。如果您遇到任何问题，您可以手动下载并重新安装。此页面的内容可能已自动翻译。要提供反馈，请填写页面底部的表单。
SES 1.9.5 Test Release Notes
The SES195.bin file is the required file for the download. It is highly
recommended that all I/O is stopped before beginning this procedure.
You must update the SES firmware on each LS module in the PowerVault 660
and each of the attached enclosures. This includes the 660F as well as all
attached 224F enclosures.
If you are replacing an LS module, or adding new PowerVault 224 units to
an existing subsystem, you should update all LS modules with this firmware.
Enclosure services must be online to update the firmware. If enclosure
services are offline then restore them to the online state before
performing the following procedure.
The SES195.bin file is the required file for the download. It is highly
recommended that all I/O is stopped before beginning this procedure.
You must update the SES firmware on each LS module in the PowerVault 660
and each of the attached enclosures. This includes the 660F as well as all
attached 224F enclosures.
If you are replacing an LS module, or adding new PowerVault 224 units to
an existing subsystem, you should update all LS modules with this firmware.
Enclosure services must be online to update the firmware. If enclosure
services are offline then restore them to the online state before
performing the following procedure.
推荐
以管理员身份登录 Windows 以使用自动扫描。如果您已以管理员身份登录并看到此消息，请重新启动。 您的系统由 IT 管理员管理，并且功能可能受限。
查找更多更新。使用 SupportAssist 查找适用于您的设备的所有最新驱动程序更新。
补丁和增强功能
Improvements to SES 1.9.5
SES 1.9.5 enhances the communication between SES modules. In the past
there were times when thresholds set on the master SES were not copied to
the slave SES. In a failover scenario the slave would apply the old
values, requiring that the user reset the new thresholds.
SES 1.9.5 enhances reporting so that when an LS module fails, Dell Open
Manage Array Manager can report the problem. The LED for the LS module
will, as in previous versions, still light when an LS module is in a
failed state.
SES 1.9.5 now reports the correct model name of the system, either PV660
or PV224.
In SES 1.3b2, upper warning/critical for LS Module temperature sensors is
45C/55C and for power supply sensors is 55C/65C, which is incorrect. The
correct settings are in SES 1.9.5 and are 35C/45C for the LS module
temperature sensors and 45C/55C for the power supply.
了解详情SES 1.9.5 enhances the communication between SES modules. In the past
there were times when thresholds set on the master SES were not copied to
the slave SES. In a failover scenario the slave would apply the old
values, requiring that the user reset the new thresholds.
SES 1.9.5 enhances reporting so that when an LS module fails, Dell Open
Manage Array Manager can report the problem. The LED for the LS module
will, as in previous versions, still light when an LS module is in a
failed state.
SES 1.9.5 now reports the correct model name of the system, either PV660
or PV224.
In SES 1.3b2, upper warning/critical for LS Module temperature sensors is
45C/55C and for power supply sensors is 55C/65C, which is incorrect. The
correct settings are in SES 1.9.5 and are 35C/45C for the LS module
temperature sensors and 45C/55C for the power supply.
版本
1.9.5, A01
发布日期
20 9月 2001
下载类型
固件
类别
光纤通道
重要性
可选Dell Technologies 建议查看此更新以确定它是否适用于您的系统。此更新包含仅影响特定配置的更改，或者提供不一定不适用于您的环境的新功能。
安装说明
To update the LS module SES firmware, perform the following steps:
1. Start Array Manager on the host system by clicking Start-- Programs--
Dell
OpenManage Applications-- Array Manager-- Array Manager Console.
2. Update the SES firmware on the PowerVault 660F.
a. Click Arrays-- PV660F SubSystem-- Physical Array.
b. Right-click the controller for the subsystem you wish to upgrade and
choose Download-- SES Firmware.
c. Select all the enclosure check boxes and click Next.
d. Click Browse and locate the SES195.bin file. Click Next.
e. Click Finish and OK.
NOTE: This process takes about 8 to 9 minutes for each additional LS
module in
the storage array. If the firmware update does not complete successfully,
repeat
the process until it does. This issue is not a hardware problem, but a
software-timing
issue.
f. After download completes, right-click the PV660F subsystem in Array
Manager and choose Rescan to update the properties information.
g. Right-click the enclosure in Array Manager, choose Properties, and
verify that it is using SES firmware version 1.9.5. If it is not, repeat
the download procedure.
h. Physically remove the primary LS module to cause failover.
i. Right-click the PV660F subsystem in Array Manager and choose Rescan
to update the properties information.
j. Right-click the enclosure and choose Properties to verify its
firmware level is also at version 1.9.5. If it is not, repeat the
download procedure.
k. Replace the LS module that you removed. If you have multiple
enclosures, you must verify the firmware level on every LS module
in the subsystem, one at a time.
1. Start Array Manager on the host system by clicking Start-- Programs--
Dell
OpenManage Applications-- Array Manager-- Array Manager Console.
2. Update the SES firmware on the PowerVault 660F.
a. Click Arrays-- PV660F SubSystem-- Physical Array.
b. Right-click the controller for the subsystem you wish to upgrade and
choose Download-- SES Firmware.
c. Select all the enclosure check boxes and click Next.
d. Click Browse and locate the SES195.bin file. Click Next.
e. Click Finish and OK.
NOTE: This process takes about 8 to 9 minutes for each additional LS
module in
the storage array. If the firmware update does not complete successfully,
repeat
the process until it does. This issue is not a hardware problem, but a
software-timing
issue.
f. After download completes, right-click the PV660F subsystem in Array
Manager and choose Rescan to update the properties information.
g. Right-click the enclosure in Array Manager, choose Properties, and
verify that it is using SES firmware version 1.9.5. If it is not, repeat
the download procedure.
h. Physically remove the primary LS module to cause failover.
i. Right-click the PV660F subsystem in Array Manager and choose Rescan
to update the properties information.
j. Right-click the enclosure and choose Properties to verify its
firmware level is also at version 1.9.5. If it is not, repeat the
download procedure.
k. Replace the LS module that you removed. If you have multiple
enclosures, you must verify the firmware level on every LS module
in the subsystem, one at a time.