AUTOMATICKY NAINSTALOVÁNOTento soubor byl automaticky nainstalován v rámci nedávné aktualizace. Pokud máte jakékoli problémy, můžete jej stáhnout a přeinstalovat ručně.
Obsah této stránky byl patrně přeložen automaticky. Chcete-li vložit zpětnou vazbu, vyplňte formulář ve spodní části stránky.
Tento soubor byl automaticky nainstalován v rámci nedávné aktualizace. Pokud máte jakékoli problémy, můžete jej stáhnout a přeinstalovat ručně.
This utility disables the startup gamma calibration routine from Maxtor Atlas 10K drives
Doporučeno
Vyhledejte nejlepší soubor ke stažení pro svůj systém.
Chcete-li zobrazit nejnovější informace o ovladači pro svůj systém, zadejte podrobnosti produktu.
Vyhledat podporu
Zadejte výrobní číslo Dell nebo model.
Chcete vyhledat svůj produkt? Vložte identifikátor produktu.Ukázat způsob
Nenalezeny žádné výsledky. Pro zadaný výraz nebylo nic nalezeno. Upravte vyhledávaný výraz a hledání opakujte.
Tento ovladač není kompatibilní
Tento ovladač není určen pro vybraný produkt. Vyberte jiný produkt a vložte údaje o produktu pro tento ovladač nebo navštivte stránku podpory produktu a podívejte se na všechny ovladače pro jiný produkt.
Chcete-li používat automatickou kontrolu, přihlaste se do systému Windows jako správce. Pokud jste již přihlášeni jako správce a zobrazí se tato zpráva, restartujte počítač.Váš systém spravuje správce IT – funkce mohou být omezené.
Najděte více aktualizací. Použijte nástroj SupportAssist k vyhledání nejnovějších aktualizací ovladačů.
Opravy a vylepšení
Initial Release History: on power up, Maxtor Atlas 10K drives generate an audible noise while executing Gamma Calibration. This noise is part of the normal start up procedure; there are no problems with the drive. This noise will not occur during an active or idle drive state after the system is fully powered on and entered a ready state. This utility disables the startup gamma calibration routine.
Společnost Dell Technologies doporučuje tuto aktualizaci zkontrolovat a zjistit, zda je pro váš systém vhodná. Aktualizace obsahuje změny, které mají vliv pouze na určité konfigurace, nebo poskytuje nové funkce, které se mohou nebo nemusí vztahovat k danému prostředí.
Formát souboru:Jeden či více samorozbalovacích obrazů disku samorozbalovacího souboru Zip
Název souboru:BR66869.exe
Velikost souboru:853.34 KB
Jde o velký soubor. Stahování může nějakou dobu trvat, v závislosti na rychlosti připojení.
Popis formátu:
Tento soubor obsahuje komprimovanou (případně komprimovanou do archivu ZIP) sadu souborů. Stáhněte soubor do složky na pevném disku a poté na něj poklepejte, rozbalí se sada souborů. Podle pokynů dokončete instalaci.
Utility must be placed on a non-write protected diskette.
NOTE: In order to create this diskette, the file must be downloaded to and executed on a system running Microsoft Windows.
Download 1. Click the "Download Now" link to download the file. 2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement. 3. When the File Download window appears, click "Save" to save the file to your hard drive.
Diskette Creation 1. Browse to the location where you downloaded the file and double-click the new file to create the diskette set. 2. Insert a blank diskette then click Continue. 3. After all the files have been copied to the last, click Finish.
Installation: NOTE: BACKUP ALL DATA BEFORE RUNNING THIS PROGRAM. Do not remove power from the devices or disturb the devices in any way while the download is in progress. Dell, Inc is not Responsible for any data loss resulting from the use of this program
NOTE: Before proceeding with the update, refer to README.TXT file, section 4.0 "Using The Update Utility" for important information regarding the update process.
For drives connected to Channel 0 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC): 1. Insert the firmware update diskette into the floppy drive and reboot the system. 2. The utility will automatically determine the correct device to update when booted 3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 1 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC): 1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line “Device=ASPIDRV\MEGASPI.SYS /a1” and adding the REM statement to the line “Device=ASPIDRV\MEGASPI.SYS /a0”. 2. Insert the firmware update diskette into the floppy drive and reboot the system. 3. The utility will automatically determine the correct device to update when booted 4. Once the update is complete Remove the diskette and reboot the system.
For drives connected an Adaptec RAID controller (PERC 3/Si, PERC 3/DI): 1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line "Device=ASPIDRV\ELITEAPI.SYS /M" and adding the ‘REM’ statement to the lines “Device=ASPIDRV\MEGASPI.SYS /a0” and “Device=ASPIDRV\MEGASPI.SYS /a1”. 2. Insert the firmware update diskette into the floppy drive and reboot the system. 3. The utility will automatically determine the correct device to update when booted 4. Once the update is complete Remove the diskette and reboot the system.