LSI Logic PERC 3/x, 4/x, 4e/x, CERC ATA 100 Driver
Genstart er nødvendig AUTOMATISK INSTALLERET Denne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.Indholdet på denne side er muligvis blevet oversat automatisk. Udfyld formularen nederst på siden for at give feedback.
This package provides the LSI Logic PERC 3/SC, 4/DC, 4/SC, 4e/DC, CERC ATA 100 Driver and is supported on the Enterprise Servers and Powervault models that are running the following Windows Operating System: Windows Server 2003.
Anbefalet
Find den bedste download til dit system
Indtast produktoplysningerne for at få vist de seneste driveroplysninger for dit systemSøg i support
Indtast din Dell-servicekode eller -model
Vil du søge efter dit produkt? Indtast et produkt-id. Vis mig hvordan
Denne driver er ikke kompatibel
Denne driver er ikke relevant for det valgte produkt. Vælg et andet produkt for at indtaste dine produktoplysninger for denne driver igen, eller gå til siden Produktsupport for at se alle drivere til et andet produkt.
Log på Windows som administrator for at bruge automatisk scanning. Hvis du allerede er logget på som administrator og får vist denne meddelelse, skal du genstarte enheden. Dit system administreres af din it-administrator, og funktionaliteten kan være begrænset.
Find flere opdateringer. Brug SupportAssist til at finde alle de seneste driveropdateringer til din enhed.
Programrettelser og forbedringer
Fixes
- If the Adapter is set to DEAD, all the IOCTLs sent to the driver will be returned with a special signature 0xEE to identify that the adapter is DEAD and not responding.
- During Bus Reset, the driver issues a call to the F/W and returns without waiting for the call to finish and asks for the next request from OS. This next request got issued to the F/W even before the reset call completed resulting in the reservation conflict. Now the driver does not issue the next command until the reset call to the F/W completes.
- SCSI commands issued to the Dummy Device exposed by the driver was not handled properly. Driver should have rejected all the commands issued to the Dummy Device except for the SCSIOP_INQUIRY and SCSIIO_READ_CAPACITY. This was causing the system to blue screen when using utilities sending SCSI commands to the Dummy Device. This release driver handles all the SCSI commands issued to the driver gracefully.
Enhancements
- N/A
Læs mere- If the Adapter is set to DEAD, all the IOCTLs sent to the driver will be returned with a special signature 0xEE to identify that the adapter is DEAD and not responding.
- During Bus Reset, the driver issues a call to the F/W and returns without waiting for the call to finish and asks for the next request from OS. This next request got issued to the F/W even before the reset call completed resulting in the reservation conflict. Now the driver does not issue the next command until the reset call to the F/W completes.
- SCSI commands issued to the Dummy Device exposed by the driver was not handled properly. Driver should have rejected all the commands issued to the Dummy Device except for the SCSIOP_INQUIRY and SCSIIO_READ_CAPACITY. This was causing the system to blue screen when using utilities sending SCSI commands to the Dummy Device. This release driver handles all the SCSI commands issued to the driver gracefully.
Enhancements
- N/A
Version
6.46.2.32, A05
Udgivelsesdato
17 jan. 2014
Downloadtype
Driver
Kategori
SCSI RAID
Vigtighed
AnbefaletDell Technologies anbefaler, at denne opdatering installeres under den næste planlagte opdateringscyklus. Opdateringen indeholder ændringer, der skal opretholde systemets generelle tilstand. Den sørger for, at systemsoftwaren forbliver opdateret og kompatibel med andre systemmoduler (firmware, BIOS, drivere og software) og kan indeholde andre nye funktioner.
Tilgængelige formater Vis vigtige oplysninger
Filformat: Opdateringspakke til MS Windows 32-bit.
Filnavn: RAID_DRVR_WIN_R99970.EXE
Filstørrelse: 1.13 MB
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Dell Update Packages (DUP) i Microsoft Windows 32-bit-format er udviklet til at køre på Microsoft Windows 64-bit-operativsystemer. Dell Update Packages (DUP) i Microsoft Windows 64-bit-format kan kun køre på Microsoft Windows 64-bit-operativsystemer. Når du vælger en driveropdatering, skal du sørge for at vælge den udgave, der passer til dit operativsystem.
Kontrollér kontrolsumværdien for at sikre overførslens integritet.
MD5:
41451665696554870A35CC2BDA98613E
SHA1:
Ikke tilgængelig
SHA-256:
Ikke tilgængelig
Filformat: Paker filer direkte ud til lokal disk
Filnavn: perc-cerc-w2k3-6.46.2.32-A05.exe
Filstørrelse: 75 KB
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Dette filformat består af et arkiv med filer, der kan dekomprimeres til en mappe på harddisken. Du kan derefter installere fra den pågældende mappe.
Kontrollér kontrolsumværdien for at sikre overførslens integritet.
MD5:
Ikke tilgængelig
SHA1:
Ikke tilgængelig
SHA-256:
Ikke tilgængelig
Filformat: Eksterne produktbemærkninger
Filnavn: perc-cerc-w2k3-6.46.2.32-A05.txt
Filstørrelse: 28.32 KB
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Dette filformat indeholder almindelig tekst, som kan vises med en standardteksteditor.
Kontrollér kontrolsumværdien for at sikre overførslens integritet.
MD5:
Ikke tilgængelig
SHA1:
Ikke tilgængelig
SHA-256:
Ikke tilgængelig
Når du downloader filerne, accepterer du samtidig betingelserne i Dells softwarelicensaftale. (på engelsk)
Understøttede operativsystemer
Windows Server 2003
Gælder for
�
CERC ATA 100
PERC 4/DC
PERC 4/SC
PERC3/SC
Installationsvejledning
Install Instructions
=======
This is a self-extracting package of the Windows 2000 and 2003 device driver installation diskette for PERC 4/DC, 4/SC, 3/QC, 3/DC, 3/DCL, 3/SC,CERC ATA100/4CH, PERC 4/Di, PERC 4e/Di, PERC4e/Si and PERC 4e/DC.To build the installation diskette, execute the package, directing its output to an empty, formatted diskette.
Installing the Driver during Operating System Installation
---------
1. Boot the system using the Microsoft Windows Server CD.
2. When the message Press F6 if you need to install a third party SCSI or RAID driver appears, press the key immediately. Within a few minutes, a screen appears that asks for additional controllers in the system.
3. Press the key. The system prompts for the driver diskette to be inserted.
4. Insert the driver diskette in the floppy drive and press the key. A list of PERC controllers appears.
5. Select the right driver for the installed controller and press the key to load the driver.
NOTE: For Windows 2003, a message appears that states that the driver that you provided is older/newer then the Windows driver. Press the key to use the driver that is on the floppy diskette.
6. Press the key again to continue the installation process as usual.
Installing a Windows Driver for a New RAID Controller
-----------
Perform the following steps to configure the driver when you add the RAID controller to a system that already has Windows installed.
1. Power down the system.
2. Install the new RAID controller in the system. Refer to Hardware Installation for detailed instructions on installing and cabling the RAID controller in the system.
3. Power on the system. The Windows operating system should detect the new controller and display a message to inform the user.
4. The Found New Hardware Wizard screen pops up and displays the detected hardware device.
5. Click Next.
6. On the Locate device driver screen, select Search for a suitable driver for my device and click Next.
7. Insert the appropriate driver diskette and select Floppy disk drives on the Locate Driver Files screen.
8. Click Next.
9. The wizard detects and installs the appropriate device drivers for the new RAID controller.
10. Click Finish to complete the installation.
11. Reboot the server.
=======
This is a self-extracting package of the Windows 2000 and 2003 device driver installation diskette for PERC 4/DC, 4/SC, 3/QC, 3/DC, 3/DCL, 3/SC,CERC ATA100/4CH, PERC 4/Di, PERC 4e/Di, PERC4e/Si and PERC 4e/DC.To build the installation diskette, execute the package, directing its output to an empty, formatted diskette.
Installing the Driver during Operating System Installation
---------
1. Boot the system using the Microsoft Windows Server CD.
2. When the message Press F6 if you need to install a third party SCSI or RAID driver appears, press the
3. Press the
4. Insert the driver diskette in the floppy drive and press the
5. Select the right driver for the installed controller and press the
NOTE: For Windows 2003, a message appears that states that the driver that you provided is older/newer then the Windows driver. Press the
6. Press the
Installing a Windows Driver for a New RAID Controller
-----------
Perform the following steps to configure the driver when you add the RAID controller to a system that already has Windows installed.
1. Power down the system.
2. Install the new RAID controller in the system. Refer to Hardware Installation for detailed instructions on installing and cabling the RAID controller in the system.
3. Power on the system. The Windows operating system should detect the new controller and display a message to inform the user.
4. The Found New Hardware Wizard screen pops up and displays the detected hardware device.
5. Click Next.
6. On the Locate device driver screen, select Search for a suitable driver for my device and click Next.
7. Insert the appropriate driver diskette and select Floppy disk drives on the Locate Driver Files screen.
8. Click Next.
9. The wizard detects and installs the appropriate device drivers for the new RAID controller.
10. Click Finish to complete the installation.
11. Reboot the server.
Hjælp og selvstudier til drivere
Du kan finde flere downloads på Drivere og overførsler. Hvis du har brug for hjælp til at bruge oplysningerne på denne side, kan du besøge Hjælp og selvstudier til drivere.