Dell PERC 6/E Adapter FW version 6.3.1-0003, A14
Genstart er nødvendig AUTOMATISK INSTALLERET Denne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.Indholdet på denne side er muligvis blevet oversat automatisk. Udfyld formularen nederst på siden for at give feedback.
This package provides the firmware for PERC 6/E Adapter firmware release version 6.3.1-0003
Anbefalet
Find den bedste download til dit system
Indtast produktoplysningerne for at få vist de seneste driveroplysninger for dit systemSøg i support
Indtast din Dell-servicekode eller -model
Vil du søge efter dit produkt? Indtast et produkt-id. Vis mig hvordan
Denne driver er ikke kompatibel
Denne driver er ikke relevant for det valgte produkt. Vælg et andet produkt for at indtaste dine produktoplysninger for denne driver igen, eller gå til siden Produktsupport for at se alle drivere til et andet produkt.
Log på Windows som administrator for at bruge automatisk scanning. Hvis du allerede er logget på som administrator og får vist denne meddelelse, skal du genstarte enheden. Dit system administreres af din it-administrator, og funktionaliteten kan være begrænset.
Find flere opdateringer. Brug SupportAssist til at finde alle de seneste driveropdateringer til din enhed.
Programrettelser og forbedringer
1. Fixes an issue where the Perc battery does not always charge up properly, causing Virtual Disks changing rom Write Back to Write Through.
2. Removes system events that relate to partial Patrol completion on physical drives.
Læs mere2. Removes system events that relate to partial Patrol completion on physical drives.
Version
6.3.1-0003, A14
Udgivelsesdato
06 dec. 2011
Downloadtype
Firmware
Kategori
SAS RAID
Vigtighed
AnbefaletDell Technologies anbefaler, at denne opdatering installeres under den næste planlagte opdateringscyklus. Opdateringen indeholder ændringer, der skal opretholde systemets generelle tilstand. Den sørger for, at systemsoftwaren forbliver opdateret og kompatibel med andre systemmoduler (firmware, BIOS, drivere og software) og kan indeholde andre nye funktioner.
Tilgængelige formater Vis vigtige oplysninger
Filformat: Opdateringspakke til Red Hat Linux
Filnavn: SAS-RAID_Firmware_FK6J2_LN32_6.3.1-0003_A14.BIN
Filstørrelse: 4.87 MB
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Dell Update Packages til Linux kan bruges som et selvstændigt program der sikrer, at specifikke valideringskriterier opfyldes, før opdateringen anvendes.
Bemærk: Opdateringspakker til Linux er open-source. Se Vigtigt-filen Dell Update Packages til Linux for at få flere oplysninger.
Bemærk: Opdateringspakker til Linux er open-source. Se Vigtigt-filen Dell Update Packages til Linux for at få flere oplysninger.
Kontrollér kontrolsumværdien for at sikre overførslens integritet.
MD5:
1eaf179f22485064c95fbf28d750c443
SHA1:
fc2344e1ae40e835becfa7b86f92ab72a22585bf
SHA-256:
Ikke tilgængelig
Filformat: En GnuPG-fil, der indeholder en kryptografisk signatur
Filnavn: SAS-RAID_Firmware_FK6J2_LN32_6.3.1-0003_A14.BIN.sign
Filstørrelse: 194 Bytes
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
GnuPG-signaturen til Red Hat Linux Update Package kan bruges til at godkende Dells identitet i den samlede Red Hat Linux Update-pakke.
Kontrollér kontrolsumværdien for at sikre overførslens integritet.
MD5:
c15c2c504517b233ecb2fa4ca5044227
SHA1:
9e3f5a4fe9603c3776f78f4c8d5236817e3908aa
SHA-256:
Ikke tilgængelig
Filformat: ZipPack-ekstern
Filnavn: DELL_PERC-6-E-ADAPTER_A14_R313331.exe
Filstørrelse: 1.9 MB
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Denne fil indeholder komprimerede (eller ZIP) filer. Hent filen til en mappe på din harddisk, og kør den derefter (dobbeltklik) for at udpakke filerne. Følg instruktionerne for at fuldføre installationen.
Kontrollér kontrolsumværdien for at sikre overførslens integritet.
MD5:
a58cc5f16ddb3207f3734ad40689c46d
SHA1:
cc06e081dce6e6a837817e605cfda38a997df327
SHA-256:
20f0eccf812fb36b3c1ea351bc87b97285c53f20e0d5ce687d8e52a19def3693
Filformat: Eksterne produktbemærkninger
Filnavn: R313331.txt
Filstørrelse: 15.07 KB
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Dette filformat indeholder almindelig tekst, som kan vises med en standardteksteditor.
Kontrollér kontrolsumværdien for at sikre overførslens integritet.
MD5:
70d518e69037ffa37e5c5be6c3881d64
SHA1:
Ikke tilgængelig
SHA-256:
Ikke tilgængelig
Filformat: Opdateringspakke til MS Windows 32-bit.
Filnavn: SAS-RAID_Firmware_FK6J2_WN32_6.3.1-0003_A14.EXE
Filstørrelse: 6.8 MB
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Dell Update Packages (DUP) i Microsoft Windows 32-bit-format er udviklet til at køre på Microsoft Windows 64-bit-operativsystemer. Dell Update Packages (DUP) i Microsoft Windows 64-bit-format kan kun køre på Microsoft Windows 64-bit-operativsystemer. Når du vælger en driveropdatering, skal du sørge for at vælge den udgave, der passer til dit operativsystem.
Kontrollér kontrolsumværdien for at sikre overførslens integritet.
MD5:
c1d9c4bec34f4675afb4c0d810eaddf5
SHA1:
5bd15bd0305001db7db0d9da3bc8ac15cd2642e7
SHA-256:
Ikke tilgængelig
Når du downloader filerne, accepterer du samtidig betingelserne i Dells softwarelicensaftale. (på engelsk)
Vigtige oplysninger
The firmware upgrade may fail if any of the RAID controllers in the system are performing an I/O background task (that is, consistency check, background initialization, rebuild, or reconstruction). Allow the background task to complete before attempting to upgrade the firmware. Patrol Read tasks will not affect a firmware upgrade.
* Linux systems running one or more applications that interact with SCSI devices in certain ways are known to cause a kernel panic situation. Therefore, it is recommended that you stop Server Administrator and its Storage Management Service before running storage controller firmware update packages.
To stop the Dell OpenManage(TM) Server Administrator service,
run "omconfig system webserver action=stop"
To start the Server Administrator service,
run "omconfig system webserver action=start"
To stop the Server Administrator Storage Management Service,
run "/etc/init.d/dataeng stop"
To start the Server Administrator Storage Management Service,
run "/etc/init.d/dataeng start"
* Linux systems running one or more applications that interact with SCSI devices in certain ways are known to cause a kernel panic situation. Therefore, it is recommended that you stop Server Administrator and its Storage Management Service before running storage controller firmware update packages.
To stop the Dell OpenManage(TM) Server Administrator service,
run "omconfig system webserver action=stop"
To start the Server Administrator service,
run "omconfig system webserver action=start"
To stop the Server Administrator Storage Management Service,
run "/etc/init.d/dataeng stop"
To start the Server Administrator Storage Management Service,
run "/etc/init.d/dataeng start"
Understøttede operativsystemer
Ikke relevant
Gælder for
PERC 6/E Adapter
Installationsvejledning
Performing the Firmware Upgrade
NOTE: This initial section of the Installation Instructions applies only to configurations with (greater than) 2TB SEDs.
1. Update the firmware version to this version using preferred method below (Zip Pack, Windows DUP, Linux DUP).
2. Reboot for the new FW take effect
3. Un-assign any (greater than) 2TB SED Dedicated or Global Hot Spares in the configuration. Not all configurations have hot spares.
4. Use CTRL-R or OMSS to issue Instant Secure Erase to all un-configured (greater than) 2TB SED drives (all data in these drives will be lost)
5. Re-assign (greater than) 2TB SED Hot Spares.
Zip pack:
Download
1. Click the Download Now link to download the file.
2. When the File Download window appears, click Save to save the file to your
hard drive.
Extract Files
1. Browse to the location where you downloaded the file and double-click the
new file to unzip the download package
2. Click Continue.
3. Specify the location to unzip the files.
4. Click onthe OK button to extract files.
After the files are extracted the message all files were successfully
unzipped will appear.
5. Click the OK button to exit from the installer.
Installation
1. Copy extracted files to bootable media.
2. Reboot system to bootable media.
3. Execute update.bat to perform flash.
5. After flash is complete, remove bootable media.
4. Reboot system for changes to take effect.
Windows Update Package:
Download
1. Click the "Download Now" link to download the file.
2. When the File Download window appears, click Save to save the file to
your hard drive.
Installation
1. Browse to the location where you downloaded the file and double-click the new file.
2. Read over the release information presented in the dialog window.
3. Download and install any prerequisites identified in the dialog window
before proceeding.
4. Click the Install button.
5. Follow the remaining prompts to perform the update.
Linux Update Package:
Download
1. Click the Download Now linkto download the file.
2. When the File Download window appears, click Save to save the file to your hard drive.
Installation
1. Read over the release information presented by executing the
./FRMW_LX_RXXXXXX.BIN --version command from the shell.
2. Download and install any prerequisites identified in the above step before
proceeding.
3. Run the update by executing ./FRMW_LX_RXXXXXX.BIN from the shell.
4. Follow the remaining prompts to perform the update.
GnuPG Signature of Dell Update Package Instructions for FRMW_LX_RXXXXXX.BIN:
Download
1. Click the Download Now link to download the file.
2. When the File Download window appears, click Save to save the file to your hard drive.
Installation
1. Import the Dell public key. (You only need to do this once on your system.)
2. Verify the Dell Update Package by using its signature file, FRMW_LX_RXXXXXX.BIN.
NOTE: This initial section of the Installation Instructions applies only to configurations with (greater than) 2TB SEDs.
1. Update the firmware version to this version using preferred method below (Zip Pack, Windows DUP, Linux DUP).
2. Reboot for the new FW take effect
3. Un-assign any (greater than) 2TB SED Dedicated or Global Hot Spares in the configuration. Not all configurations have hot spares.
4. Use CTRL-R or OMSS to issue Instant Secure Erase to all un-configured (greater than) 2TB SED drives (all data in these drives will be lost)
5. Re-assign (greater than) 2TB SED Hot Spares.
Zip pack:
Download
1. Click the Download Now link to download the file.
2. When the File Download window appears, click Save to save the file to your
hard drive.
Extract Files
1. Browse to the location where you downloaded the file and double-click the
new file to unzip the download package
2. Click Continue.
3. Specify the location to unzip the files.
4. Click onthe OK button to extract files.
After the files are extracted the message all files were successfully
unzipped will appear.
5. Click the OK button to exit from the installer.
Installation
1. Copy extracted files to bootable media.
2. Reboot system to bootable media.
3. Execute update.bat to perform flash.
5. After flash is complete, remove bootable media.
4. Reboot system for changes to take effect.
Windows Update Package:
Download
1. Click the "Download Now" link to download the file.
2. When the File Download window appears, click Save to save the file to
your hard drive.
Installation
1. Browse to the location where you downloaded the file and double-click the new file.
2. Read over the release information presented in the dialog window.
3. Download and install any prerequisites identified in the dialog window
before proceeding.
4. Click the Install button.
5. Follow the remaining prompts to perform the update.
Linux Update Package:
Download
1. Click the Download Now linkto download the file.
2. When the File Download window appears, click Save to save the file to your hard drive.
Installation
1. Read over the release information presented by executing the
./FRMW_LX_RXXXXXX.BIN --version command from the shell.
2. Download and install any prerequisites identified in the above step before
proceeding.
3. Run the update by executing ./FRMW_LX_RXXXXXX.BIN from the shell.
4. Follow the remaining prompts to perform the update.
GnuPG Signature of Dell Update Package Instructions for FRMW_LX_RXXXXXX.BIN:
Download
1. Click the Download Now link to download the file.
2. When the File Download window appears, click Save to save the file to your hard drive.
Installation
1. Import the Dell public key. (You only need to do this once on your system.)
2. Verify the Dell Update Package by using its signature file, FRMW_LX_RXXXXXX.BIN.
Hjælp og selvstudier til drivere
Du kan finde flere downloads på Drivere og overførsler. Hvis du har brug for hjælp til at bruge oplysningerne på denne side, kan du besøge Hjælp og selvstudier til drivere.