Genstart er nødvendigAUTOMATISK INSTALLERETDenne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.
Indholdet på denne side er muligvis blevet oversat automatisk. Udfyld formularen nederst på siden for at give feedback.
Denne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.
This package provides the Micron C400 32GB/64GB/128GB/256GB mSATA Firmware Update and is supported on the Alienware Notebook, Inspiron, Latitude, OptiPlex, Precision, Vostro and XPS models that are running Windows series operation systems.
Anbefalet
Find den bedste download til dit system
Indtast produktoplysningerne for at få vist de seneste driveroplysninger for dit system
Søg i support
Indtast din Dell-servicekode eller -model
Vil du søge efter dit produkt? Indtast et produkt-id.Vis mig hvordan
Søgningen gav ingen resultater.Vi kunne ikke finde nogen match til din søgning. Rediger din søgning, og prøv igen.
Denne driver er ikke kompatibel
Denne driver er ikke relevant for det valgte produkt. Vælg et andet produkt for at indtaste dine produktoplysninger for denne driver igen, eller gå til siden Produktsupport for at se alle drivere til et andet produkt.
Log på Windows som administrator for at bruge automatisk scanning. Hvis du allerede er logget på som administrator og får vist denne meddelelse, skal du genstarte enheden.Dit system administreres af din it-administrator, og funktionaliteten kan være begrænset.
Find flere opdateringer. Brug SupportAssist til at finde alle de seneste driveropdateringer til din enhed.
Programrettelser og forbedringer
Fixes: - Fixed issues where SSD may not be detected after a previous forced power cycle.
Enhancements: - Enhanced the device ready time, allowing system to be able to power up quickly.
Dell Technologies anbefaler at gennemse denne opdatering for at afgøre, om den er relevant for dit system. Opdateringen indeholder ændringer, der kun har indflydelse på visse konfigurationer, eller tilvejebringer nye funktioner, der muligvis passer til dit miljø.
1. Equipment needed, a CD drive, a blank CD 2. Do not POWER OFF the system during the firmware update procedure 3. Please perform a full system backup before starting the firmware update procedure (highly recommended) 4. Connect your notebook to a AC power supply during the firmware update procedure (highly recommended) 5. The firmware utility tool is OS independent.
1. It is highly recommended that full system backup be completed before starting this firmware upgrade procedure
Download and image extraction
1. Click Download to download the zipped file 2. Extract the file into a folder 3. The ISO image file is used to burn the utility onto a bootable CD
Installation
1. Ensure that your notebook is plugged into a AC power supply during the update process (high recommended) 2. DO NOT remove power from the system during the firmware update process 3. Ensure that your BIOS has been set to ATA or AHCI mode. DO NOT select RAID mode. This utility will not work in RAID mode 4. Ensure that your BIOS boot order has been set up to boot from CD drive a. You can do so by either pressing F12 during the boot up and then select CD drive to boot from b. Or by pressing F2 during the boot up, enter the boot order selection and select CD drive to boot from. Save the setting before exiting 5. Insert the bootable CD media with ISO image into yoursystem 6. Reboot the system from the bootable CD media, the firmware update utility will be started automatically 7. Connected Micron SSD drive that is eligible for the firmware update will be shown on the screen 8. Select Yes to the request for 'Update firmware on this drive?' 9. DO NOT power off the system during the update process, the update will take about 30 to 60 seconds. Some systems may require a longer time to complete. 10.Upon completion, the message 'Current Firmware is : 04MH' will be displayed.