American Megatrends (AMI) PERC 2/SC, PERC2/DC, v.6.32.2.32, A00
AUTOMATISK INSTALLERETDenne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.
Indholdet på denne side er muligvis blevet oversat automatisk. Udfyld formularen nederst på siden for at give feedback.
Denne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.
PERC 2/SC-DC device driver for Windows Server 2003.
Anbefalet
Find den bedste download til dit system
Indtast produktoplysningerne for at få vist de seneste driveroplysninger for dit system
Søg i support
Indtast din Dell-servicekode eller -model
Vil du søge efter dit produkt? Indtast et produkt-id.Vis mig hvordan
Søgningen gav ingen resultater.Vi kunne ikke finde nogen match til din søgning. Rediger din søgning, og prøv igen.
Denne driver er ikke kompatibel
Denne driver er ikke relevant for det valgte produkt. Vælg et andet produkt for at indtaste dine produktoplysninger for denne driver igen, eller gå til siden Produktsupport for at se alle drivere til et andet produkt.
Log på Windows som administrator for at bruge automatisk scanning. Hvis du allerede er logget på som administrator og får vist denne meddelelse, skal du genstarte enheden.Dit system administreres af din it-administrator, og funktionaliteten kan være begrænset.
Find flere opdateringer. Brug SupportAssist til at finde alle de seneste driveropdateringer til din enhed.
Programrettelser og forbedringer
Changes from 6.25 =================
1) Changes in the setup files, so that Scsiport driver should give the correct device number and function number to the miniport driver.
2) A timeout is implemented in the driver so that driver shouldn't wait infinitely for the firmware to acknowledge the interrupt.
3) The driver will return an error status for all the offline logical drives.
4) Utilities are issuing 0xc3 calls for getting the logical drive statistics. This is causing the system to crash. This bug has been fixed in the driver.
5) The driver is using Hal functions to program hierarchy bridges and SCSI chips when system goes to D3 standby state.
The use of Hal functions were not allowing the driver to pass the HCT test. So we have to disable the Hal calls in the previous releases. A workaround has been done in the driver whereby all the Hal calls have been replaced by its assembly equivalent.
6) During reset, the driver was not clearing all the pending commands whenever the firmware is not able to complete it.
7) Driver is allocating enough continuous memory for the FLASH_WRITE_BLOCK(0x2c) command.
8) The system gives a blue screen when one swaps the boot controller. This bug has been fixed by adding entries of all the supported controllers in the critical data base section of the registry through changes in the oemsetup.inf file.
9) The system was not waking up after a hibernation/standby operation. This bug was caused by the driver. The driver was trying to access PCI_CONFIG space from the ScsiRestartAdapter in the driver. This bug has been fixed by accessing the PCI_CONFIG space from the ScsiSetRunningConfig entry point.
10) A new command has been introduced to enhance the performance for SCSI I/O on non-raid SCSI channel.
11) In case of standby, the driver was not waiting for the firmware to get initialized. This resulted in the driver sending commands to the firmware even when the firmware is not initialized. The fix has been put in the driver. The driver is polling for the Firmware to get initialized before sending any commands to the firmware.
Dell Technologies anbefaler, at denne opdatering installeres under den næste planlagte opdateringscyklus. Opdateringen indeholder ændringer, der skal opretholde systemets generelle tilstand. Den sørger for, at systemsoftwaren forbliver opdateret og kompatibel med andre systemmoduler (firmware, BIOS, drivere og software) og kan indeholde andre nye funktioner.
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Dell Update Packages (DUP) i Microsoft Windows 32-bit-format er udviklet til at køre på Microsoft Windows 64-bit-operativsystemer. Dell Update Packages (DUP) i Microsoft Windows 64-bit-format kan kun køre på Microsoft Windows 64-bit-operativsystemer. Når du vælger en driveropdatering, skal du sørge for at vælge den udgave, der passer til dit operativsystem.
This program creates a Windows 2000 driver diskette for the controllers. You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
1) Download the file to a directory on your hard drive. The file downloaded is a self extracting executable. 2) Double click on the file to run the executable. 3) Click on the unzip button to extract files to the floppy.
Power down the system and install the PERC/CERC card. Configure the logical drives before proceeding with the driver install described below.
Installing on a new driver on a Windows Server 2003 system ----------------------------------------------------------
1) Boot the system using the Windows Server 2003 CD. As the message
"Press F6 if you need to install a third party SCSI or RAID driver."
appears, press F6 immediately.
2) Within a few minutes, a screen appears that asks for additional adapters in the system. Choose 'S'.
3) You are prompted for the driver diskette. Insert the PERC/CERC Windows Server 2003 driver diskette in the floppy drive and press Enter.
4) A list of drivers for PERC/CERC controllers appears. Select the right driver for your installed controller and press Enter to load the driver.
5) A statement is presented saying the driver that you provided is older then the Windows driver.
Press 'S' to use the driver on the floppy.
6) Press Enter again to continue installation process as usual.
Adding the PERC/CERC Driver to an Existing Windows Server 2003. --------------------------------------------------------------
1) Boot the system to Windows 2003. The Found New Hardware Wizard displays.
2) If you are installing the PERC 3/SC, PERC 4/DC PERC 4/SC, PERC 4/DI or CERC ATA100/4CH, click on Next and skip to step 5. Otherwise, click Cancel on all the new devices.
3) Restart the system from the shutdown menu.
4) The Found New Hardware Wizard displays again when the system boots to Windows Server 2003. Click on Next.
5) Select Search for a suitable driver and click Next to continue.
6) Select Floppy disk drive, insert the PERC/CERC Windows 2003 driver diskette created above and click Next to continue.
7) Continue to click on Next and finish the installation.
8) The Found New Hardware Wizard screen appears one time for each PERC 3/SC, PERC 4/SC, PERC 4/DC controller, three times for each PERC 3/DC or PERC 3/DCL controller and four times for each PERC 3/QC. Repeat steps 5 - 7 for each time the wizard displays to complete installation of the card.
9) To confirm driver installation, right click on My Computer and select Manage. Click on Device Manager, then click on SCSI and RAID controllers to see the newly added PERC 3 controller(s) in the list.
After finishing the driver update, YOU MUST REBOOT YOUR SERVER.
Updating the PERC/CERC Driver to an Existing Windows Server 2003. ------------------------------------------------------------------------
If your server is already running Windows Server 2003, use the following steps to update the PERC Windows Server 2003 driver.
1) Insert the PERC/CERC Windows Server 2003 driver diskette.
2) Position the mouse pointer on the my computer icon on your Start Menu andright click and select Manage.
3) Position the mouse pointer on Device Manager and click the left mouse button .
4) Position the mouse pointer on SCSI and RAID controllers and double click.
5) Select the PERC controller and double click.
6) Select the Driver tab
7) Select the Update Driver
The Upgrade Device Driver Wizard displays.
8) Select ”Install from a list of specific location” and click Next to continue.
9) Select “Search for the best driver in these locations” and make sure that the “search removable media (floppy, cd-rom,…)” option is checked. Then click on the Next but