American Megatrends (AMI) PERC 2/SC, PERC2/DC, v.6.35.2.32, A02
AUTOMATISK INSTALLERETDenne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.
Indholdet på denne side er muligvis blevet oversat automatisk. Udfyld formularen nederst på siden for at give feedback.
Denne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.
Dell PowerEdge RAID Controller 2/DC and 2/SC Device Driver for Windows 2003.
Version 6.35.2.32
Anbefalet
Find den bedste download til dit system
Indtast produktoplysningerne for at få vist de seneste driveroplysninger for dit system
Søg i support
Indtast din Dell-servicekode eller -model
Vil du søge efter dit produkt? Indtast et produkt-id.Vis mig hvordan
Søgningen gav ingen resultater.Vi kunne ikke finde nogen match til din søgning. Rediger din søgning, og prøv igen.
Denne driver er ikke kompatibel
Denne driver er ikke relevant for det valgte produkt. Vælg et andet produkt for at indtaste dine produktoplysninger for denne driver igen, eller gå til siden Produktsupport for at se alle drivere til et andet produkt.
Log på Windows som administrator for at bruge automatisk scanning. Hvis du allerede er logget på som administrator og får vist denne meddelelse, skal du genstarte enheden.Dit system administreres af din it-administrator, og funktionaliteten kan være begrænset.
Find flere opdateringer. Brug SupportAssist til at finde alle de seneste driveropdateringer til din enhed.
Programrettelser og forbedringer
Fixes or Enhancements in this Release
Enhancements: 1) None
Fixes: 1) Minor change to Oemsetup.txt file.
2) Driver no longer filters out all other commands except SCSI READ and SCSI WRITE
Dell Technologies anbefaler at gennemse denne opdatering for at afgøre, om den er relevant for dit system. Opdateringen indeholder ændringer, der kun har indflydelse på visse konfigurationer, eller tilvejebringer nye funktioner, der muligvis passer til dit miljø.
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Dell Update Packages (DUP) i Microsoft Windows 32-bit-format er udviklet til at køre på Microsoft Windows 64-bit-operativsystemer. Dell Update Packages (DUP) i Microsoft Windows 64-bit-format kan kun køre på Microsoft Windows 64-bit-operativsystemer. Når du vælger en driveropdatering, skal du sørge for at vælge den udgave, der passer til dit operativsystem.
Dell PowerEdge RAID Controller 2/SC, 2/DC, 4/DC, 4/SC, 3/QC, 3/DC, 3/DCL, 3/SC, 4/DI, and CERC ATA100/4CH, Device Driver for Windows Server 2003.
Version 6.35.2.32
Download
1. Click the "Download Now" link to download the file. 2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement. 3. When the File Download window appears, click "Save" to save the file to your hard drive.
Extract Files
1. Browse to the location where you downloaded the file and double-click the new file to unzip the download package. 2. Specify the location to unzip the files – the instructions below assume you extract files to a formatted floppy disk. 3. Click on the unzip button to extract files.
Installation
Dell PowerEdge RAID Controller 4/DC, 4/SC, 3/QC, 3/DC, 3/DCL, 3/SC, 4/DI, and CERC ATA100/4CH, Device Driver for Windows Server 2003.
Version 6.35.2.32
Installing on a new driver on a Windows Server 2003 system
1) Boot the system using the Windows Server 2003 CD. As the message "Press F6 if you need to install a third party SCSI or RAID driver." appears, press F6 immediately.
2) Within a few minutes, a screen appears that asks for additional adapters in the system. Choose 'S'.
3) You are prompted for the driver diskette. Insert the PERC/CERC Windows Server 2003 driver diskette in the floppy drive and press Enter.
4) A list of drivers for PERC/CERC controllers appears. Select the right driver for your installed controller and press Enter to load the driver.
5) A statement is presented saying the driver that you provided is older/newer then the Windows driver.
Press 'S' to use the driver on the floppy.
6) Press Enter again to continue installation process as usual.
Adding the PERC/CERC Driver to an Existing Windows Server 2003.
1) Boot the system to Windows 2003. The Found New Hardware Wizard displays.
2) If you are installing the PERC 3/SC, PERC 4/DC, PERC 4/SC, PERC 4/DI or CERC ATA100/4CH, click on Next and skip to step 5. Otherwise, click Cancel on all the new devices.
3) Restart the system from the shutdown menu.
4) The Found New Hardware Wizard displays again when the system boots to Windows Server 2003. Click on Next.
5) Select Search for a suitable driver and click "Next" to continue.
6) Select Floppy disk drive, insert the PERC/CERC Windows 2003 driver diskette created above and click Next to continue.
7) Continue to click on Next and finish the installation.
8) The Found New Hardware Wizard screen appears one time for each PERC 3/SC, PERC 4/SC, PERC 4/DC controller, three times for each PERC 3/DC or PERC 3/DCL controller and four times for each PERC 3/QC. Repeat steps 5 - 7 for each time the wizard displays to complete installation of the card.
9) To confirm driver installation, right click on My Computer and select Manage. Click on Device Manager, then click on SCSI and RAID controllers to see the newly added PERC 3 controller(s) in the list.
After finishing the driver update, YOU MUST REBOOT YOUR SERVER.
Updating the PERC/CERC Driver on an Existing Windows Server 2003.
If your server is already running Windows Server 2003, use the following steps to update the PERC Windows Server 2003 driver.
Note: If your driver supports multiple RAID controllers, make sure to upgrade all the RAID controllers in your system that your driver supports.
1) Insert the PERC/CERC Windows Server 2003 driver diskette.
2) Position the mouse pointer to the my computer icon in the Start menu and right click and select Manage.
3) Position the mouse pointer on Device Manager and click the left mouse button.
4) Position the mouse pointer on SCSI and RAID controllers and double click.