Micron RealSSD C400 128GB/256GB/512GB 2.5" 7MM Firmware Update
Genstart er nødvendig AUTOMATISK INSTALLERET Denne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.Indholdet på denne side er muligvis blevet oversat automatisk. Udfyld formularen nederst på siden for at give feedback.
This package provides the Micron RealSSD C400 128GB/256GB/512GB 2.5" 7MM Firmware Update and is supported on Alienware, Inspiron, Latitude, XPS Notebook, OptiPlex, Precision and Vostro Notebook models that are running the following Windows Operating Systems: Windows 7 and Windows 8.
Anbefalet
Find den bedste download til dit system
Indtast produktoplysningerne for at få vist de seneste driveroplysninger for dit systemSøg i support
Indtast din Dell-servicekode eller -model
Vil du søge efter dit produkt? Indtast et produkt-id. Vis mig hvordan
Denne driver er ikke kompatibel
Denne driver er ikke relevant for det valgte produkt. Vælg et andet produkt for at indtaste dine produktoplysninger for denne driver igen, eller gå til siden Produktsupport for at se alle drivere til et andet produkt.
Log på Windows som administrator for at bruge automatisk scanning. Hvis du allerede er logget på som administrator og får vist denne meddelelse, skal du genstarte enheden. Dit system administreres af din it-administrator, og funktionaliteten kan være begrænset.
Find flere opdateringer. Brug SupportAssist til at finde alle de seneste driveropdateringer til din enhed.
Programrettelser og forbedringer
Fixes
- Fixed issues where SSD may not be detected after a previous forced power cycle.
Enhancements
- Enhanced the device ready time, allowing system to be able to power up quickly.
Læs mere- Fixed issues where SSD may not be detected after a previous forced power cycle.
Enhancements
- Enhanced the device ready time, allowing system to be able to power up quickly.
Version
040H, A00-00
Udgivelsesdato
04 mar. 2013
Downloadtype
Firmware
Kategori
Storage
Vigtighed
ValgfritDell Technologies anbefaler at gennemse denne opdatering for at afgøre, om den er relevant for dit system. Opdateringen indeholder ændringer, der kun har indflydelse på visse konfigurationer, eller tilvejebringer nye funktioner, der muligvis passer til dit miljø.
Tilgængelige formater Vis vigtige oplysninger
Filformat: Firmware-billeder
Filnavn: Micron C400 7MM 040H.zip
Filstørrelse: 1.86 MB
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Kontrollér kontrolsumværdien for at sikre overførslens integritet.
MD5:
8c093ee80739f53404219cbf429f8f35
SHA1:
c4270268c05b006f6c8e7a3e2bca74a1300bc7c7
SHA-256:
8c5339f143d75bac4c397153a4558628754a43d44472fe734adfaf6e27598938
Når du downloader filerne, accepterer du samtidig betingelserne i Dells softwarelicensaftale. (på engelsk)
Vigtige oplysninger
1. Equipment needed, a CD drive, a blank CD.
2. Do not POWER OFF the system during the firmware update procedure.
3. Please perform a full system backup before starting the firmware update procedure (highly recommended).
4. Connect your notebook to a AC power supply during the firmware update procedure (highly recommended).
5.The firmware utility tool is OS independent.
2. Do not POWER OFF the system during the firmware update procedure.
3. Please perform a full system backup before starting the firmware update procedure (highly recommended).
4. Connect your notebook to a AC power supply during the firmware update procedure (highly recommended).
5.The firmware utility tool is OS independent.
Understøttede operativsystemer
Windows 7, 32-bit
Windows 7, 64-bit
Windows 8, 32-bit
Windows 8, 64-bit
Gælder for
Micron RealSSD C400
Installationsvejledning
Backup
1. It is highly recommended that full system backup be completed before starting this firmware upgrade procedure.
Download and image extraction
1. Click Download File to download the zipped file.
2. Extract the file into a folder.
3. The ISO image file is used to burn the utility onto a bootable CD.
Installation
1. Ensure that your notebook is plugged into a AC power supply during the update process (high recommended).
2. DO NOT remove power from the system during the firmware update process.
3. Ensure that your BIOS has been set to ATA or AHCI mode. DO NOT select RAID mode. This utility will not work in RAID mode.
4. Ensure that your BIOS boot order has been set up to boot from CD drive
a. You can do so by either pressing F12 during the boot up and then select CD drive to boot from
b. Or by pressing F2 during the boot up, enter the boot order selection and select CD drive to boot from. Save the setting before exiting.
5. Insert the bootable CD media with ISO image into your system.
6. Reboot the system from the bootable CD media, the firmware update utility will be started automatically.
7. Connected Micron SSD drive that is eligible for the firmware update will be shown on the screen.
8. Select Yes to the request 'Update firmware on this drive?'
9. DO NOT power off the system during the update process, the update will take about 30 to 60 seconds. Some systems may require a longer time to complete.
10. Upon completion, the message 'Current Firmware is: 040H' will be displayed.
1. It is highly recommended that full system backup be completed before starting this firmware upgrade procedure.
Download and image extraction
1. Click Download File to download the zipped file.
2. Extract the file into a folder.
3. The ISO image file is used to burn the utility onto a bootable CD.
Installation
1. Ensure that your notebook is plugged into a AC power supply during the update process (high recommended).
2. DO NOT remove power from the system during the firmware update process.
3. Ensure that your BIOS has been set to ATA or AHCI mode. DO NOT select RAID mode. This utility will not work in RAID mode.
4. Ensure that your BIOS boot order has been set up to boot from CD drive
a. You can do so by either pressing F12 during the boot up and then select CD drive to boot from
b. Or by pressing F2 during the boot up, enter the boot order selection and select CD drive to boot from. Save the setting before exiting.
5. Insert the bootable CD media with ISO image into your system.
6. Reboot the system from the bootable CD media, the firmware update utility will be started automatically.
7. Connected Micron SSD drive that is eligible for the firmware update will be shown on the screen.
8. Select Yes to the request 'Update firmware on this drive?'
9. DO NOT power off the system during the update process, the update will take about 30 to 60 seconds. Some systems may require a longer time to complete.
10. Upon completion, the message 'Current Firmware is: 040H' will be displayed.
Hjælp og selvstudier til drivere
Du kan finde flere downloads på Drivere og overførsler. Hvis du har brug for hjælp til at bruge oplysningerne på denne side, kan du besøge Hjælp og selvstudier til drivere.