Maxtor Aurora 15K U320 18GB 68 Pin, Aurora 15K U320 18GB 80 Pin, Aurora 15K U320 36GB 68 Pin, Aurora 15K U320 36GB 80 Pin, Aurora 15K U320 73GB 68 Pin, Aurora 15K U320 73GB 80 Pin, v.1.0, A00
INSTALACIÓN AUTOMÁTICA Se ha instalado este archivo automáticamente como parte de una actualización reciente. Si tiene algún problema, lo puede descargar y reinstalar manualmente.Es posible que el contenido de esta página se haya traducido automáticamente. Si desea proporcionar comentarios, complete el formulario de la parte inferior de la página.
This utility disables the read-lookahead (ESP) feature of the drive.
Recomendado
Encuentre la mejor descarga para su sistema
Introduzca los detalles del producto para ver la información del controlador más reciente para su sistemaBúsqueda de asistencia
Introduzca la etiqueta de servicio de Dell o el modelo
¿Desea buscar un producto? Introduzca un identificador de producto. ¿Cómo lo hago?
Este controlador no es compatible.
Este controlador no es aplicable para el producto seleccionado. Elija otro producto si desea reintroducir los detalles del producto para este controlador o visite la página Asistencia para productos si desea ver todos los controladores disponibles para un producto distinto.
Inicie sesión en Windows como administrador para utilizar los análisis automáticos. Si ya ha iniciado sesión como administrador y ve este mensaje, reinicie el sistema. Su administrador de TI gestiona el sistema y es posible que haya funciones limitadas.
Busque más actualizaciones. Utilice SupportAssist para buscar las actualizaciones de controladores más recientes para su dispositivo.
Correcciones y mejoras
Initial Release
A timeout problem was reported with Maxtor Atlas 15K SCSI hard disk drives running a specific Hard Drive Stress test script under Linux 9.0 within a PE1600SC system. When the Messages log file within Linux is viewed, a System Timeout, Bus Reset, and 04/40/0C check condition may be recorded.
This issue was found while running the Hard Drive stress test. There is no known customer reported problem running a specific application. In this test environment, the drive is requested to perform reverse sequential reads. In some cases, this issue can intermittently create an internal race condition causing the the drive to ‘hang’, requiring the Operating system to issue a bus reset.
Más informaciónA timeout problem was reported with Maxtor Atlas 15K SCSI hard disk drives running a specific Hard Drive Stress test script under Linux 9.0 within a PE1600SC system. When the Messages log file within Linux is viewed, a System Timeout, Bus Reset, and 04/40/0C check condition may be recorded.
This issue was found while running the Hard Drive stress test. There is no known customer reported problem running a specific application. In this test environment, the drive is requested to perform reverse sequential reads. In some cases, this issue can intermittently create an internal race condition causing the the drive to ‘hang’, requiring the Operating system to issue a bus reset.
Versión
1.0, A00
Fecha de publicación
31 oct 2003
Tipo de descarga
Utilidad
Categoría
Unidad SCSI
Importancia
OpcionalDell Technologies recomienda revisar esta actualización para determinar si se aplica a su sistema. La actualización contiene cambios que afectan solamente a ciertas configuraciones u ofrecen nuevas funciones que pueden aplicarse o no a su entorno.
Formatos disponibles
Formato de archivo: Una o varias imágenes de disco autoextraíbles dentro de un zip autoextraíble
Nombre de archivo: BR67588.exe
Tamaño de archivo: 881.34 KB
Se trata de un archivo de gran tamaño. Tardará un tiempo en descargarse, dependiendo de la velocidad de la conexión.
Descripción del formato:
Este archivo contiene un conjunto de archivos comprimidos. Descargue el archivo en una carpeta del disco duro y, a continuación, haga doble clic en él para descomprimir el conjunto de archivos. Siga las instrucciones para realizar la instalación.
Para garantizar la integridad de la descarga, compruebe el valor de la suma de comprobación.
MD5:
No disponible
SHA1:
No disponible
SHA-256:
No disponible
Al realizar la descarga, acepta los términos del Acuerdo de licencia de software de Dell. (en ingles)
Sistemas operativos compatibles
Red Hat® Enterprise Linux 2.1
Red Hat® Linux 8.0
Red Hat® Linux 9.0
Windows Server 2003
Windows 2000
Se aplica a
Aurora 15K U320 18GB 68 Pin
Aurora 15K U320 18GB 80 Pin
Aurora 15K U320 36GB 68 Pin
Aurora 15K U320 36GB 80 Pin
Aurora 15K U320 73GB 68 Pin
Aurora 15K U320 73GB 80 Pin
Instrucciones de instalación
Custom Instructions for BR67588.exe:
Utility must be placed on a non-write protected diskette.
NOTE: In order to create this diskette, the file must be downloaded to and executed on a system running Microsoft Windows.
Download
1. Click the "Download Now" link to download the file.
2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement.
3. When the File Download window appears, click "Save" to save the file to your hard drive.
Diskette Creation
1. Browse to the location where you downloaded the file and double-click the new file to create the diskette set.
2. Insert a blank diskette then click Continue.
3. After all the files have been copied to the last, click Finish.
Installation:
NOTE: BACKUP ALL DATA BEFORE RUNNING THIS PROGRAM. Do not remove power from the devices or disturb the devices in any way while the download is in progress. Dell, Inc is not Responsible for any data loss resulting from the use of this program
NOTE: Before proceeding with the update, refer to README.TXT file, section 4.0 "Using The Update Utility" for important information regarding the update process.
For drives connected to an LSI 1020 or 1030 SCSI controller:
1. Insert the firmware update diskette into the floppy drive and reboot the system.
2. The utility will automatically determine the correct device to update when booted
3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to an Adapted 7899 or 39160 SCSI controller:
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line Device=ASPIDRV\ASPI8U2.SYS and adding the ‘REM’ statement to the line Device=ASPIDRV\ASPIMPT.SYS. This modification loads the ASPI driver for Adaptec controllers instead of the ASPI driver for LSI controllers
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 0 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC):
1. Insert the firmware update diskette into the floppy drive and reboot the system.
2. The utility will automatically determine the correct device to update when booted
3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 1 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC):
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line “Device=ASPIDRV\MEGASPI.SYS /a1” and adding the REM statement to the line “Device=ASPIDRV\MEGASPI.SYS /a0”.
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.
For drives connected an Adaptec RAID controller (PERC 3/Si, PERC 3/DI):
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line "Device=ASPIDRV\ELITEAPI.SYS /M" and adding the ‘REM’ statement to the lines “Device=ASPIDRV\MEGASPI.SYS /a0” and “Device=ASPIDRV\MEGASPI.SYS /a1”.
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.
Utility must be placed on a non-write protected diskette.
NOTE: In order to create this diskette, the file must be downloaded to and executed on a system running Microsoft Windows.
Download
1. Click the "Download Now" link to download the file.
2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement.
3. When the File Download window appears, click "Save" to save the file to your hard drive.
Diskette Creation
1. Browse to the location where you downloaded the file and double-click the new file to create the diskette set.
2. Insert a blank diskette then click Continue.
3. After all the files have been copied to the last, click Finish.
Installation:
NOTE: BACKUP ALL DATA BEFORE RUNNING THIS PROGRAM. Do not remove power from the devices or disturb the devices in any way while the download is in progress. Dell, Inc is not Responsible for any data loss resulting from the use of this program
NOTE: Before proceeding with the update, refer to README.TXT file, section 4.0 "Using The Update Utility" for important information regarding the update process.
For drives connected to an LSI 1020 or 1030 SCSI controller:
1. Insert the firmware update diskette into the floppy drive and reboot the system.
2. The utility will automatically determine the correct device to update when booted
3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to an Adapted 7899 or 39160 SCSI controller:
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line Device=ASPIDRV\ASPI8U2.SYS and adding the ‘REM’ statement to the line Device=ASPIDRV\ASPIMPT.SYS. This modification loads the ASPI driver for Adaptec controllers instead of the ASPI driver for LSI controllers
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 0 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC):
1. Insert the firmware update diskette into the floppy drive and reboot the system.
2. The utility will automatically determine the correct device to update when booted
3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 1 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC):
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line “Device=ASPIDRV\MEGASPI.SYS /a1” and adding the REM statement to the line “Device=ASPIDRV\MEGASPI.SYS /a0”.
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.
For drives connected an Adaptec RAID controller (PERC 3/Si, PERC 3/DI):
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line "Device=ASPIDRV\ELITEAPI.SYS /M" and adding the ‘REM’ statement to the lines “Device=ASPIDRV\MEGASPI.SYS /a0” and “Device=ASPIDRV\MEGASPI.SYS /a1”.
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.
Ayuda para controladores y tutoriales
Para ver más descargas, vaya a Controladores y descargas. Para obtener ayuda sobre cómo usar la información de esta página, visite Tutoriales y ayuda para controladores.