Dell SAS Hard Drive Firmware Utility, SATA Hard Drive Firmware Utility, v.Seagate SAS, A00
ASENNETTU AUTOMAATTISESTITämä tiedosto asennettiin automaattisesti osana hiljattaista päivitystä. Jos sinulla on tässä ongelmia, voit ladata ja asentaa sen manuaalisesti uudelleen.
Tämän sivun sisältö on saatettu kääntää automaattisesti. Voit antaa palautetta täyttämällä sivun alareunassa olevan lomakkeen.
Tämä tiedosto asennettiin automaattisesti osana hiljattaista päivitystä. Jos sinulla on tässä ongelmia, voit ladata ja asentaa sen manuaalisesti uudelleen.
Seagate drives not seen during SMTD installation or after adding additional drives online in Linux. This is a special release targeted only for 5 Seagate SAS drives listed in the Fixes and Enhancements section.
R211868 is intended for all other firmware updates.
Suositellut
Etsi paras lataus järjestelmällesi
Voit tarkastella järjestelmäsi uusimpia ajuritietoja antamalla tuotteen tiedot.
Hae tukea
Anna Dell-palvelutunniste tai -malli
Haluatko etsiä tuotteesi? Anna tuotetunnistin.Ohjeet
Tuloksia ei löytynyt. Haku ei tuottanut tuloksia. Muokkaa hakua ja yritä uudelleen
Tämä ajuri ei ole yhteensopiva
Tämä ohjain ei sovi valitulle tuotteelle. Valitse toinen tuote, jos haluat antaa ohjaimen tuotetiedot uudelleen, tai siirry tuotetukisivulle, jossa voit tarkastella eri tuotteen kaikkia ohjaimia.
Kirjaudu Windowsiin järjestelmänvalvojana, jotta voit käyttää automaattista tarkistusta. Jos olet jo kirjautunut järjestelmänvalvojana ja näet tämän viestin, käynnistä järjestelmä uudelleen.Järjestelmänvalvoja hallinnoi järjestelmääsi, minkä vuoksi ominaisuuksia voi olla rajoitettu.
Etsi lisää päivityksiä. Etsi laitteesi uusimmat ajuripäivitykset SupportAssistin avulla.
Korjaukset ja parannukset
Several Seagate drives shipped from Dell factories between February 2nd and February 20th may experience the following symptoms: A) During an install from System Management Tool and Documentation DVD: 1. If there is no RAID config from ctrl-r and the DVD is booted it will display a blank white screen where there should be array configuration setup. 2. If there is a RAID config from ctrl-r already present on the drives, it will boot to the SMTD DVD but skip the RAID config screen. The menu item for RAID config in the left window will not appear in the action list. Install can be completed using this method.
B) Enclosure or server hard drives are being configured or added in an existing Linux install: The drives my not be seen in the Linux browser that is using Open Manage Storage Management to configure the drives. Or, the Vendor ID for the disk drive may appear with garbled characters.
The FW version on the drive label will represent the correct firmware version; however, a later version was flashed to the drive in the factory.
Dell Technologies suosittelee asentamaan päivityksen seuraavan päivityskierroksen yhteydessä. Päivitys sisältää muutoksia järjestelmän yleisen kunnon säilyttämiseksi. Se varmistaa, että järjestelmäohjelmisto pysyy ajan tasalla ja yhteensopivana muiden järjestelmämoduulien kanssa (laiteohjelmisto, BIOS, ohjaimet ja ohjelmistot) ja sisältää myös muita uusia ominaisuuksia.
Tiedosto on suuri. Lataus saattaa kestää jonkin aikaa, jos yhteys on hidas.
Alusta kuvaus:
Tämä tiedosto sisältää pakattuja (zipattuja) tiedostoja. Lataa tiedosto kiintolevyllä olevaan kansioon ja pura tiedostot suorittamalla tiedoston (kaksoisnapsauttamalla sitä). Suorita asennus loppuun toimimalla ohjeiden mukaan.
This release is intended for use on drives attached to SAS/ PERC controllers and MD1000 Enclosures.
Please note: Only Dell Branded SAS/SCSI and PERC controllers are supported. Embedded SATA controllers are not supported.
On drives attached to PERC5/PERC6 controllers, the first drive to be updated requires a 5 minute delay before firmware flash to begin. Do not power cycle or reboot your system while the update is in progress.
1. Click the "Download Now" link to download the file. 2. When the File Download window appears, click "Save" to save the file to your hard drive.
Installation
1. Browse to the location where you downloaded the file and double-click the new file. 2. Read over the release information presented in the dialog window. 3. Download and install any prerequisites identified in the dialog window before proceeding. 4. Click the Install button. 5. Follow the remaining prompts to perform the update.
1) Click Download now. The File Download window appears.
2) Click the Save button. The Save As window appears.
3) Select Desktop using the drop-down menu to the right of Save in.
4) Click the Save button. A progress meter moves as the download is completed.
5) If necessary, click X in the upper right-hand corner of the Download Progress Window to close it upon completion.
6) Double click the Icon on your desktop for the newly saved file. The Dell Bios Release Notes window appears.