INSTALADO AUTOMÁTICAMENTEEste archivo se instaló automáticamente como parte de una actualización reciente. Si experimenta algún problema, puede descargarlo y reinstalarlo manualmente.
Es posible que el contenido de esta página se traduzca automáticamente. Para proporcionar comentarios, complete el formulario en la parte inferior de la página.
Este archivo se instaló automáticamente como parte de una actualización reciente. Si experimenta algún problema, puede descargarlo y reinstalarlo manualmente.
PERC 4/Di Device Driver for Red Hat Linux 7.2.
Recomendado
Encuentre la mejor descarga para su sistema
Ingrese los detalles del producto para ver la información más reciente del controlador para el sistema
Buscar soporte
Ingrese su modelo o etiqueta de servicio de Dell
¿Desea buscar su producto? Ingrese un identificador de producto.Mostrarme cómo
No se encontraron resultados. No pudimos encontrar ningún resultado para la búsqueda. Modifique la búsqueda e inténtelo de nuevo.
Este controlador no es compatible
Este controlador no se corresponde con el producto seleccionado. Elija otro producto para volver a ingresar los detalles del producto para este controlador o visite la página Soporte de productos para ver todos los controladores de un producto diferente.
Inicie sesión en Windows como administrador para utilizar el escaneo automático. Si ya inició sesión como administrador y ve este mensaje, reinicie el sistema.El administrador de TI administra el sistema y es posible que las funciones sean limitadas.
Encuentre más actualizaciones. Utilice SupportAssist para encontrar todas las actualizaciones de controladores más recientes para su dispositivo.
Dell Technologies recomienda revisar esta actualización para determinar si corresponde a su sistema. La actualización contiene cambios que afectan solamente a ciertas configuraciones u ofrecen nuevas funciones que pueden aplicarse o no a su entorno.
Formato de archivo:Extrae archivos directamente al disco local
File Name:perc4di-118c-72c.tar.gz
Tamaño del archivo:538.62 KB
Este es un archivo grande. La descarga puede tardar, dependiendo de la velocidad de conexión.
Descripción del formato:
Este formato de archivo consiste en un archivo de archivos que se pueden descomprimir a un directorio en el disco duro. La instalación puede realizarse desde ese directorio.
Instructions for downloading and creating driver diskette: ----------------------------------------------------------
You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
Download the file PERC4di-118c-72c.tar.gz to a temporary directory on your working system.
Extract the file to the floppy disk as follows:
1. On a Linux system:
Type the following commands under a Linux command shell: mount /dev/fd0 /mnt/floppy tar xvzf -C /mnt/floppy (Eg: /temp/PERC4di-118c-72c.tar.gz) umount /mnt/floppy
2. On a Microsoft Windows system:
You can use Winzip to extract tar.gz archives. However, note the following settings under Winzip to ensure correct extraction of the files.
Start Winzip -> Go to Options -> Configuration
Under the Miscellaneous tab make sure "TAR file smart CR/LF conversion" is unchecked.
Upon opening the tar.gz archive with Winzip, you get the following prompt:
'Archive contains one file. Should Winzip decompress it to a temporary folder and open it?'
Press 'yes' and extract the files normally under Winzip to the floppy drive.
Install Red Hat Linux 7.2 driver for PERC 4/Di as a boot controller -------------------------------------------------------
There are two ways of installing Red Hat 7.2 driver onto the PERC 4/Di as a boot controller. One is using a driver disk during OS installation and the second is using a driver (megaraid) RPM to update driver after OS is installed. The steps for both of these methods are provided below. All the files needed for both methods are included in the driver diskette created above.
For more detailed installation instructions of Red Hat 7.2, please refer to the OS installation guide at http://www.dell.com/linux.
I. Installing driver during OS installation: --------------------------------------------
1. Boot normally from the Redhat installation CD-Rom.
2. Type 'linux dd' on the boot prompt.
3. When the install prompts for a driver disk, insert the driver diskette created above and press 'Enter'.
4. Installation progresses normally. Continue until the 'Create Bootdisk' screen. Press CTRL-ALT-F2 to get to a shell window and type the following commands:
chroot /mnt/sysimage cd /boot /sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10 lilo ( only if lilo was used as bootloader. If grub used - skip this step ) exit
Press CTRL-ALT-F7 to get back to the install screen.
5. Complete the installation as directed by the install.
II. Update driver using RPMs after OS is installed --------------------------------------------------
Type the following commands under a Linux command shell:
mount /dev/fd0 /mnt/floppy cd /mnt/floppy ./megarpmwrapper.sh
Than follow the on-screen instructions to install the RPM driver.
For more detailed information about the script megarpmwrapper.sh, please refer to the release_notes.txt included in the release.