This package provides the new firmware for power supplier and is supported on LiteOn 1100W PSU (PN: NTCWP & PN: GYH9V) running on the Windows and Linux operating systems.
Microsoft Windows 32 位元格式的 Dell 更新套件 (DUP) 經過精心設計,可在 Microsoft Windows 64 位元作業系統上執行。Microsoft Windows 64 位元格式的 Dell 更新套件 (DUP) 只能在 Microsoft Windows 64 位元作業系統上執行。選擇裝置驅動程式更新時,請務必選擇適用您作業系統的更新。
請以系統管理員身分登入 Windows,以使用自動掃描。如果您已經以系統管理員身分登入並看到此訊息,請重新開機。您的系統會由 IT 管理員管理,且功能可能會受到限制。
尋找更多更新。使用 SupportAssist 為您的裝置尋找所有最新的驅動程式更新。
修復及強化
Fixes - A slightly oscillation on the voltage of CShare output pin was found during the test on dynamic load transient under 1+1 and 2+2 configurations. The oscillation will be gone after loading gets stable. - PAGE_PLUS_READ does not support STATUS_BYTE
IMPORTANT: After a successful power supply firmware download, the managed system turns off for a duration ranging from three to ten minutes to continue updating the firmware. Once the firmware update is complete, the managed system reboots automatically.
CAUTION! Performing an AC power cycle or cold boot during a power supply firmware update, forces the power supply unit into an irrecoverable state and the managed system does not boot.
CAUTION: Performing an AC power cycle or cold boot during a power supply firmware update, forces the power supply unit (PSU) into an irrecoverable state and the managed system does not boot.
IMPORTANT: After a successful power supply firmware download, the managed system turns off for a duration ranging from three to twenty minutes to continue updating the firmware. It is imperative not to interrupt/restart manually during this time. Update time can vary but should be approximately 10 minutes. Margin should be added to assure the Dell Update Package (DUP) is not interrupted (some DUPs may take up to 20 minutes). Once the firmware update is complete, the managed system reboots automatically.
Instructions for ".BIN" File:
Download 1. Click the Download Now link to download the file. 2. When the "File Download" window appears, click Save to save the file to your hard drive.
Installation 1. Read the release information presented by executing the ".BIN" file with "--version" command from the shell. 2. Download and install any prerequisites identified in the above step before proceeding. 3. Run the update by executing ".BIN " file from the shell. 4. Follow the remaining prompts to perform the update. 5. Upon successful completion the DUP will prompt to reboot system. 6. Restart your system. After the system restarts, DUP will enter USC to complete the flashing of the PSU firmware. 7. The actual flash begins after DUP exits USC. Please do not power off or power cycle the system as this can result in a non-functional power supply. 8. Once the flashing process is complete the system should power back up and boot to OS.
Instructions for ".EXE" File:
Download 1. Click the "Download Now" link to download the file. 2. When the "File Download" window appears, click "Save" to save the file to your hard drive.
Installation 1. Browse to the location where you downloaded the file and double-click the new file. 2. Read the release information presented in the dialog window. 3. Download and install any prerequisites identified in the dialog window before proceeding. 4. Click the Install button. 5. Follow the remaining prompts to perform the update. 6. Upon successful completion the DUP will prompt to reboot system. 7. Restart your system. After the system restarts, DUP will enter USC to complete the flashing of the PSU firmware. 8. The actual flash begins after DUP exits USC. Please do not power off or power cycle the system as this can result in a non-functional power supply. 9. Once the flashing process is complete the system should power back up and boot to OS.
GnuPG Signature of Dell Update Package Instructions for ".sign" File:
Download 1. Click the "Download Now" link to download the file. 2. When the "File Download" window appears, click "Save" to save the file to your hard drive.
Installation 1. Import the Dell public key. (You only need to import once on your system.) 2. Verify the Dell Update Package by using its signature file. 3. Upon successful completion the DUP will prompt to reboot system. 4. Restart your system. After the system restarts, DUP will enter USC to complete the flashing of the PSU firmware. 5. The actual flash begins after DUP exits USC. Please do not power off or power cycle the system as this can result in a non-functional power supply. 6. Once the flashing process is complete the system should power back up and boot to OS.