American Megatrends (AMI) PERC 2/SC, PERC2/DC, v.6.32.2.32, A00
已自動安裝 此檔案會在最近更新時自動安裝。如果您遇到任何問題，可以手動下載並重新安裝。此頁面的內容可能經過電腦自動翻譯。若要提供意見回饋，請填寫頁面底部的表單。
PERC 2/SC-DC device driver for Windows Server 2003.
建議
請以系統管理員身分登入 Windows，以使用自動掃描。如果您已經以系統管理員身分登入並看到此訊息，請重新開機。 您的系統會由 IT 管理員管理，且功能可能會受到限制。
尋找更多更新。使用 SupportAssist 為您的裝置尋找所有最新的驅動程式更新。
修復及強化
Changes from 6.25
=================
1) Changes in the setup files, so that Scsiport driver should give the
correct device number and function number to the miniport driver.
2) A timeout is implemented in the driver so that driver shouldn't
wait infinitely for the firmware to acknowledge the interrupt.
3) The driver will return an error status for all the offline logical
drives.
4) Utilities are issuing 0xc3 calls for getting the logical drive
statistics. This is causing the system to crash. This bug has been
fixed in the driver.
5) The driver is using Hal functions to program hierarchy bridges
and SCSI chips when system goes to D3 standby state.
The use of Hal functions were not allowing the driver to pass
the HCT test. So we have to disable the Hal calls in the previous
releases. A workaround has been done in the driver whereby all the
Hal calls have been replaced by its assembly equivalent.
6) During reset, the driver was not clearing all the pending commands
whenever the firmware is not able to complete it.
7) Driver is allocating enough continuous memory for the
FLASH_WRITE_BLOCK(0x2c) command.
8) The system gives a blue screen when one swaps the boot controller.
This bug has been fixed by adding entries of all the supported
controllers in the critical data base section of the registry through
changes in the oemsetup.inf file.
9) The system was not waking up after a hibernation/standby operation.
This bug was caused by the driver. The driver was trying to access
PCI_CONFIG space from the ScsiRestartAdapter in the driver.
This bug has been fixed by accessing the PCI_CONFIG space from the
ScsiSetRunningConfig entry point.
10) A new command has been introduced to enhance the performance for
SCSI I/O on non-raid SCSI channel.
11) In case of standby, the driver was not waiting for the firmware
to get initialized. This resulted in the driver sending commands to
the firmware even when the firmware is not initialized. The fix has
been put in the driver. The driver is polling for the Firmware to
get initialized before sending any commands to the firmware.
閱讀更多=================
1) Changes in the setup files, so that Scsiport driver should give the
correct device number and function number to the miniport driver.
2) A timeout is implemented in the driver so that driver shouldn't
wait infinitely for the firmware to acknowledge the interrupt.
3) The driver will return an error status for all the offline logical
drives.
4) Utilities are issuing 0xc3 calls for getting the logical drive
statistics. This is causing the system to crash. This bug has been
fixed in the driver.
5) The driver is using Hal functions to program hierarchy bridges
and SCSI chips when system goes to D3 standby state.
The use of Hal functions were not allowing the driver to pass
the HCT test. So we have to disable the Hal calls in the previous
releases. A workaround has been done in the driver whereby all the
Hal calls have been replaced by its assembly equivalent.
6) During reset, the driver was not clearing all the pending commands
whenever the firmware is not able to complete it.
7) Driver is allocating enough continuous memory for the
FLASH_WRITE_BLOCK(0x2c) command.
8) The system gives a blue screen when one swaps the boot controller.
This bug has been fixed by adding entries of all the supported
controllers in the critical data base section of the registry through
changes in the oemsetup.inf file.
9) The system was not waking up after a hibernation/standby operation.
This bug was caused by the driver. The driver was trying to access
PCI_CONFIG space from the ScsiRestartAdapter in the driver.
This bug has been fixed by accessing the PCI_CONFIG space from the
ScsiSetRunningConfig entry point.
10) A new command has been introduced to enhance the performance for
SCSI I/O on non-raid SCSI channel.
11) In case of standby, the driver was not waiting for the firmware
to get initialized. This resulted in the driver sending commands to
the firmware even when the firmware is not initialized. The fix has
been put in the driver. The driver is polling for the Firmware to
get initialized before sending any commands to the firmware.
繁體中文版
6.32.2.32, A00
發佈日期
01 5月 2003
下載類型
驅動程式
類別
SCSI RAID
重要性
建議Dell Technologies 建議您在下一個排定的更新週期套用此更新。此更新包含的變更可維持整體的系統健全狀況。此更新可確保系統軟體保持在最新狀態並與其他系統模組 (韌體、BIOS、驅動程式及軟體) 相容，並且可能包含其他新功能。
可用的格式
檔案格式： 適用於 MS Windows (32 位元) 的更新套件
檔案名稱： RAID-DRVR-R57743.exe
檔案大小： 1.09 MB
此為大型檔案。視您的連線速度而定，下載可能需要一些時間。
格式說明:
Microsoft Windows 32 位元格式的 Dell 更新套件 (DUP) 經過精心設計，可在 Microsoft Windows 64 位元作業系統上執行。Microsoft Windows 64 位元格式的 Dell 更新套件 (DUP) 只能在 Microsoft Windows 64 位元作業系統上執行。選擇裝置驅動程式更新時，請務必選擇適用您作業系統的更新。
為了確保下載的完整性，請驗證總和檢查值。
MD5：
E0F3F8C4DA3D7411D3C530D342BE5D08
SHA1：
不適用
SHA-256：
不適用
檔案格式： 將檔案直接解壓縮至本機磁碟
檔案名稱： PERC2-WS2K3-632A00.exe
檔案大小： 95.44 KB
此為大型檔案。視您的連線速度而定，下載可能需要一些時間。
格式說明:
當您開始下載，即表示您接受 Dell 軟體授權協定 (英文版) 的條款。
安裝指示
Custom Instructions for PERC2-WS2K3-632A00.exe:
This program creates a Windows 2000 driver diskette for the
controllers. You will need a formatted 3 1/2 inch floppy
diskette for the following procedure.
1) Download the file to a directory on your hard drive. The
file downloaded is a self extracting executable.
2) Double click on the file to run the executable.
3) Click on the unzip button to extract files to the floppy.
Power down the system and install the PERC/CERC card.
Configure the logical drives before proceeding with the
driver install described below.
Installing on a new driver on a Windows Server 2003 system
----------------------------------------------------------
1) Boot the system using the Windows Server 2003 CD.
As the message
"Press F6 if you need to install a third party SCSI or
RAID driver."
appears, press F6 immediately.
2) Within a few minutes, a screen appears that asks for
additional adapters in the system. Choose 'S'.
3) You are prompted for the driver diskette. Insert the
PERC/CERC Windows Server 2003 driver diskette in the floppy
drive and press Enter.
4) A list of drivers for PERC/CERC controllers appears.
Select the right driver for your installed controller and
press Enter to load the driver.
5) A statement is presented saying the driver that you provided
is older then the Windows driver.
Press 'S' to use the driver on the floppy.
6) Press Enter again to continue installation process as
usual.
Adding the PERC/CERC Driver to an Existing Windows Server 2003.
--------------------------------------------------------------
1) Boot the system to Windows 2003. The Found New Hardware
Wizard displays.
2) If you are installing the PERC 3/SC, PERC 4/DC PERC 4/SC,
PERC 4/DI or CERC ATA100/4CH, click on Next and
skip to step 5. Otherwise, click Cancel on all the new devices.
3) Restart the system from the shutdown menu.
4) The Found New Hardware Wizard displays again when the
system boots to Windows Server 2003. Click on Next.
5) Select Search for a suitable driver and click Next to
continue.
6) Select Floppy disk drive, insert the PERC/CERC Windows
2003 driver diskette created above and click Next to
continue.
7) Continue to click on Next and finish the installation.
8) The Found New Hardware Wizard screen appears one time for
each PERC 3/SC, PERC 4/SC, PERC 4/DC controller, three
times for each PERC 3/DC or PERC 3/DCL controller
and four times for each PERC 3/QC. Repeat steps 5 - 7 for each
time the wizard displays to complete installation of the card.
9) To confirm driver installation, right click on My
Computer and select Manage. Click on Device Manager, then
click on SCSI and RAID controllers to see the newly added
PERC 3 controller(s) in the list.
After finishing the driver update, YOU MUST REBOOT YOUR SERVER.
Updating the PERC/CERC Driver to an Existing Windows Server 2003.
------------------------------------------------------------------------
If your server is already running Windows Server 2003, use the
following steps
to update the PERC Windows Server 2003 driver.
1) Insert the PERC/CERC Windows Server 2003 driver diskette.
2) Position the mouse pointer on the my computer icon on your Start
Menu andright click and select Manage.
3) Position the mouse pointer on Device Manager and click the left
mouse
button .
4) Position the mouse pointer on SCSI and RAID controllers and double
click.
5) Select the PERC controller and double click.
6) Select the Driver tab
7) Select the Update Driver
The Upgrade Device Driver Wizard displays.
8) Select ”Install from a list of specific location” and click Next to
continue.
9) Select “Search for the best driver in these locations” and make sure
that the “search removable media (floppy, cd-rom,…)” option is
checked. Then click on the Next but
This program creates a Windows 2000 driver diskette for the
controllers. You will need a formatted 3 1/2 inch floppy
diskette for the following procedure.
1) Download the file to a directory on your hard drive. The
file downloaded is a self extracting executable.
2) Double click on the file to run the executable.
3) Click on the unzip button to extract files to the floppy.
Power down the system and install the PERC/CERC card.
Configure the logical drives before proceeding with the
driver install described below.
Installing on a new driver on a Windows Server 2003 system
----------------------------------------------------------
1) Boot the system using the Windows Server 2003 CD.
As the message
"Press F6 if you need to install a third party SCSI or
RAID driver."
appears, press F6 immediately.
2) Within a few minutes, a screen appears that asks for
additional adapters in the system. Choose 'S'.
3) You are prompted for the driver diskette. Insert the
PERC/CERC Windows Server 2003 driver diskette in the floppy
drive and press Enter.
4) A list of drivers for PERC/CERC controllers appears.
Select the right driver for your installed controller and
press Enter to load the driver.
5) A statement is presented saying the driver that you provided
is older then the Windows driver.
Press 'S' to use the driver on the floppy.
6) Press Enter again to continue installation process as
usual.
Adding the PERC/CERC Driver to an Existing Windows Server 2003.
--------------------------------------------------------------
1) Boot the system to Windows 2003. The Found New Hardware
Wizard displays.
2) If you are installing the PERC 3/SC, PERC 4/DC PERC 4/SC,
PERC 4/DI or CERC ATA100/4CH, click on Next and
skip to step 5. Otherwise, click Cancel on all the new devices.
3) Restart the system from the shutdown menu.
4) The Found New Hardware Wizard displays again when the
system boots to Windows Server 2003. Click on Next.
5) Select Search for a suitable driver and click Next to
continue.
6) Select Floppy disk drive, insert the PERC/CERC Windows
2003 driver diskette created above and click Next to
continue.
7) Continue to click on Next and finish the installation.
8) The Found New Hardware Wizard screen appears one time for
each PERC 3/SC, PERC 4/SC, PERC 4/DC controller, three
times for each PERC 3/DC or PERC 3/DCL controller
and four times for each PERC 3/QC. Repeat steps 5 - 7 for each
time the wizard displays to complete installation of the card.
9) To confirm driver installation, right click on My
Computer and select Manage. Click on Device Manager, then
click on SCSI and RAID controllers to see the newly added
PERC 3 controller(s) in the list.
After finishing the driver update, YOU MUST REBOOT YOUR SERVER.
Updating the PERC/CERC Driver to an Existing Windows Server 2003.
------------------------------------------------------------------------
If your server is already running Windows Server 2003, use the
following steps
to update the PERC Windows Server 2003 driver.
1) Insert the PERC/CERC Windows Server 2003 driver diskette.
2) Position the mouse pointer on the my computer icon on your Start
Menu andright click and select Manage.
3) Position the mouse pointer on Device Manager and click the left
mouse
button .
4) Position the mouse pointer on SCSI and RAID controllers and double
click.
5) Select the PERC controller and double click.
6) Select the Driver tab
7) Select the Update Driver
The Upgrade Device Driver Wizard displays.
8) Select ”Install from a list of specific location” and click Next to
continue.
9) Select “Search for the best driver in these locations” and make sure
that the “search removable media (floppy, cd-rom,…)” option is
checked. Then click on the Next but