Dell SAS Hard Drive Firmware Utility, SATA Hard Drive Firmware Utility, v.Seagate SAS, A00
AUTOMATIKUSAN TELEPÍTETTEz a fájl automatikusan települt egy korábbi frissítés részeként. Ha bármilyen problémát tapasztal, manuálisan letöltheti és újratelepítheti.
Lehet, hogy az oldal tartalma gépi fordítás útján lett fordítva. Visszajelzés küldéséhez töltse ki az oldal alján található űrlapot.
Ez a fájl automatikusan települt egy korábbi frissítés részeként. Ha bármilyen problémát tapasztal, manuálisan letöltheti és újratelepítheti.
Seagate drives not seen during SMTD installation or after adding additional drives online in Linux. This is a special release targeted only for 5 Seagate SAS drives listed in the Fixes and Enhancements section.
R211868 is intended for all other firmware updates.
Ajánlott
Keresse meg a legjobb letöltést a rendszeréhez
Kérjük, adja meg a termék adatait a rendszeréhez tartozó legfrissebb illesztőprograminformációk megtekintéséhez.
Keresés a támogatási adatok között
Adja meg Dell-szervizcímkéjét vagy -modelljét
Szeretné kikeresni termékét? Adjon meg egy termékazonosítót.Mutasd meg, hogyan!
No results found.We couldn't find anything for your search. Please modify your search and try again.
This driver is not compatible
This driver is not applicable for the selected product. Choose another product to re-enter your product details for this driver or visit the Product Support page to view all drivers for a different product.
Az automatikus ellenőrzés használatához jelentkezzen be a Windowsba rendszergazdaként. Ha már bejelentkezett rendszergazdaként, és látja ezt az üzenetet, kérjük, indítsa újra a számítógépet.A rendszert az IT-rendszergazda kezeli, és előfordulhat, hogy a funkciók köre korlátozott.
További frissítések. A SupportAssist segítségével megtalálhatja az eszközéhez elérhető legújabb illesztőprogram-frissítéseket.
Fixes & Enhancements
Several Seagate drives shipped from Dell factories between February 2nd and February 20th may experience the following symptoms: A) During an install from System Management Tool and Documentation DVD: 1. If there is no RAID config from ctrl-r and the DVD is booted it will display a blank white screen where there should be array configuration setup. 2. If there is a RAID config from ctrl-r already present on the drives, it will boot to the SMTD DVD but skip the RAID config screen. The menu item for RAID config in the left window will not appear in the action list. Install can be completed using this method.
B) Enclosure or server hard drives are being configured or added in an existing Linux install: The drives my not be seen in the Linux browser that is using Open Manage Storage Management to configure the drives. Or, the Vendor ID for the disk drive may appear with garbled characters.
The FW version on the drive label will represent the correct firmware version; however, a later version was flashed to the drive in the factory.
A Dell Technologies azt javasolja, hogy a frissítést a következő ütemezett frissítési ciklusban telepítse. A frissítés változásokat tartalmaz a rendszer megfelelő állapotának fenntartása érdekében. Biztosítja, hogy a rendszerszoftver naprakész és kompatibilis maradjon más rendszermodulokkal (firmware, BIOS, illesztőprogramok és szoftverek), és más új funkciókat is tartalmazhat.
Ez egy nagy fájl. A kapcsolat sebességétől függően a letöltés eltarthat egy ideig.
Formátum leírása:
This file contains a compressed (or zipped) set of files. Download the file to a folder on your hard drive, and then run (double-click) it to unzip the set of files. Follow the instructions to complete the installation.
This release is intended for use on drives attached to SAS/ PERC controllers and MD1000 Enclosures.
Please note: Only Dell Branded SAS/SCSI and PERC controllers are supported. Embedded SATA controllers are not supported.
On drives attached to PERC5/PERC6 controllers, the first drive to be updated requires a 5 minute delay before firmware flash to begin. Do not power cycle or reboot your system while the update is in progress.
1. Click the "Download Now" link to download the file. 2. When the File Download window appears, click "Save" to save the file to your hard drive.
Installation
1. Browse to the location where you downloaded the file and double-click the new file. 2. Read over the release information presented in the dialog window. 3. Download and install any prerequisites identified in the dialog window before proceeding. 4. Click the Install button. 5. Follow the remaining prompts to perform the update.
Detailed Instructions
1) Click Download now. The File Download window appears.
2) Click the Save button. The Save As window appears.
3) Select Desktop using the drop-down menu to the right of Save in.
4) Click the Save button. A progress meter moves as the download is completed.
5) If necessary, click X in the upper right-hand corner of the Download Progress Window to close it upon completion.
6) Double click the Icon on your desktop for the newly saved file.
Illesztőprogramokkal kapcsolatos súgó és oktatóanyagok