AUTOMATIKUSAN TELEPÍTETTEz a fájl automatikusan települt egy korábbi frissítés részeként. Ha bármilyen problémát tapasztal, manuálisan letöltheti és újratelepítheti.
Lehet, hogy az oldal tartalma gépi fordítás útján lett fordítva. Visszajelzés küldéséhez töltse ki az oldal alján található űrlapot.
Ez a fájl automatikusan települt egy korábbi frissítés részeként. Ha bármilyen problémát tapasztal, manuálisan letöltheti és újratelepítheti.
This utility disables the startup gamma calibration routine from Maxtor Atlas 10K drives
Ajánlott
Keresse meg a legjobb letöltést a rendszeréhez
Kérjük, adja meg a termék adatait a rendszeréhez tartozó legfrissebb illesztőprograminformációk megtekintéséhez.
Keresés a támogatási adatok között
Adja meg Dell-szervizcímkéjét vagy -modelljét
Szeretné kikeresni termékét? Adjon meg egy termékazonosítót.Mutasd meg, hogyan!
No results found.We couldn't find anything for your search. Please modify your search and try again.
This driver is not compatible
This driver is not applicable for the selected product. Choose another product to re-enter your product details for this driver or visit the Product Support page to view all drivers for a different product.
Az automatikus ellenőrzés használatához jelentkezzen be a Windowsba rendszergazdaként. Ha már bejelentkezett rendszergazdaként, és látja ezt az üzenetet, kérjük, indítsa újra a számítógépet.A rendszert az IT-rendszergazda kezeli, és előfordulhat, hogy a funkciók köre korlátozott.
További frissítések. A SupportAssist segítségével megtalálhatja az eszközéhez elérhető legújabb illesztőprogram-frissítéseket.
Fixes & Enhancements
Initial Release History: on power up, Maxtor Atlas 10K drives generate an audible noise while executing Gamma Calibration. This noise is part of the normal start up procedure; there are no problems with the drive. This noise will not occur during an active or idle drive state after the system is fully powered on and entered a ready state. This utility disables the startup gamma calibration routine.
Dell Technologies recommends reviewing this update to determine if it applies to your system. The update contains changes that impact only certain configurations or provides new features that may or may not apply to your environment.
Fájlformátum:One or more self extracting disk images inside of a self extracting zip
Fájlnév:BR66869.exe
Fájlméret:853.34 KB
Ez egy nagy fájl. A kapcsolat sebességétől függően a letöltés eltarthat egy ideig.
Formátum leírása:
This file contains a compressed (or zipped) set of files. Download the file to a folder on your hard drive, then double-click it to unzip the set of files. Follow the instructions to complete the installation.
Utility must be placed on a non-write protected diskette.
NOTE: In order to create this diskette, the file must be downloaded to and executed on a system running Microsoft Windows.
Download 1. Click the "Download Now" link to download the file. 2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement. 3. When the File Download window appears, click "Save" to save the file to your hard drive.
Diskette Creation 1. Browse to the location where you downloaded the file and double-click the new file to create the diskette set. 2. Insert a blank diskette then click Continue. 3. After all the files have been copied to the last, click Finish.
Installation: NOTE: BACKUP ALL DATA BEFORE RUNNING THIS PROGRAM. Do not remove power from the devices or disturb the devices in any way while the download is in progress. Dell, Inc is not Responsible for any data loss resulting from the use of this program
NOTE: Before proceeding with the update, refer to README.TXT file, section 4.0 "Using The Update Utility" for important information regarding the update process.
For drives connected to Channel 0 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC): 1. Insert the firmware update diskette into the floppy drive and reboot the system. 2. The utility will automatically determine the correct device to update when booted 3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 1 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC): 1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line “Device=ASPIDRV\MEGASPI.SYS /a1” and adding the REM statement to the line “Device=ASPIDRV\MEGASPI.SYS /a0”. 2. Insert the firmware update diskette into the floppy drive and reboot the system. 3. The utility will automatically determine the correct device to update when booted 4. Once the update is complete Remove the diskette and reboot the system.
For drives connected an Adaptec RAID controller (PERC 3/Si, PERC 3/DI): 1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line "Device=ASPIDRV\ELITEAPI.SYS /M" and adding the ‘REM’ statement to the lines “Device=ASPIDRV\MEGASPI.SYS /a0” and “Device=ASPIDRV\MEGASPI.SYS /a1”. 2. Insert the firmware update diskette into the floppy drive and reboot the system. 3. The utility will automatically determine the correct device to update when booted 4. Once the update is complete Remove the diskette and reboot the system.
Illesztőprogramokkal kapcsolatos súgó és oktatóanyagok