Dell PowerVault 35F, D9913D
INSTALLATO AUTOMATICAMENTE Questo file è stato installato automaticamente come parte di un aggiornamento recente. In caso di problemi, è possibile scaricarlo e reinstallarlo manualmente.È possibile che il contenuto di questa pagina sia stato tradotto automaticamente. Per fornire un feedback, compila il modulo che si trova in fondo alla pagina.
PowerVault 35F, firmware d9913d
Consigliato
Trova il download migliore disponibile per il sistema
Inserisci i dettagli del prodotto per visualizzare le ultime informazioni sui driver per il sistemaCerca supporto
Inserisci il modello o il codice di matricola Dell
Desideri cercare il tuo prodotto? Inserisci l'ID del prodotto. Mostrami come procedere
Questo driver non è compatibile
Questo driver non è applicabile per il prodotto selezionato. Scegli un altro prodotto per inserire nuovamente i dettagli per questo driver o visita la pagina supporto prodotti per visualizzare tutti i driver disponibili per un prodotto diverso.
Accedi a Windows come amministratore per utilizzare la scansione automatica. Se hai già effettuato l'accesso come amministratore e appare questo messaggio, riavvia il sistema. Il sistema è gestito dall'amministratore IT ed è possibile che le funzionalità siano limitate.
Trova ulteriori aggiornamenti. Usa SupportAssist per trovare tutti gli ultimi aggiornamenti dei driver per il tuo dispositivo.
Correzioni e miglioramenti
This release resolves a Netware issue in which the Veritas Backup Exec
v8.5 startup sequence may hang with "Initializing Tape Hardware" when
configured in a shared storage (SSO) environment.
Più dettagliv8.5 startup sequence may hang with "Initializing Tape Hardware" when
configured in a shared storage (SSO) environment.
Versione
d9913d, D9913D
Data di rilascio
06 feb 2001
Tipo di download
Firmware
Categoria
Fibre Channel
Importanza
OpzionaleDell Technologies consiglia di rivedere questo aggiornamento per stabilire se è applicabile al sistema. L'aggiornamento contiene modifiche che interessano solo alcune configurazioni oppure offre nuove funzioni applicabili o meno all’ambiente in questione.
Formati disponibili
Formato file: ZipPack esterno
Nome file: d9913d.exe
Dimensioni file: 601.37 KB
File di grandi dimensioni. A seconda della velocità di connessione, l'operazione di download potrebbe richiedere tempo.
Descrizione del formato:
Questo file contiene un set compresso di file. Scaricare il file in una cartella sul disco rigido, quindi eseguirlo (fare doppio clic) per decomprimere il set di file. Seguire le istruzioni per completare l'installazione.
Per assicurare l'integrità del download, verificare il valore del checksum.
MD5:
Non disponibile
SHA1:
Non disponibile
SHA-256:
Non disponibile
Con il download l'utente accetta i termini del Contratto di licenza del software Dell. (in Inglese)
Sistemi operativi supportati
non applicabile
Istruzioni di installazione
PowerVault 35F Firmware Download Instructions
The PowerVault 35F can either use FTP, TFTP or a serial connection (using
the XMODEM protocol) to update the firmware. In order to update the
firmware via the serial connection, the PowerVault 35F must be connected
to a terminal emulation program supporting XMODEM transfers. This menu
item does not appear when accessing the configuration menus through Telnet.
1. Download and run the file D9913D.EXE. This will extract the contents
of the archive to a temporary directory (i.e. x:\Dell\Drivers\PV35F\).
2. Decide the method for firmware download (FTP, TFTP, or Serial
Connection) and proceed to the appropriate instructions.
FTP Method
1. Make sure your PowerVault 35F is connected to a network and the IP
address is set properly.
2. Start your FTP program using the PowerVault 35F’ s IP address. Type
ftp (IP address).
NOTE: The default IP address is 1.1.1.1. See your PowerVault 35F User’s
Manual for instructions on changing the IP address.
3. Use root as the user name and password as the password.
NOTE: This is the default user name and password for the PowerVault 35F.
If you have changed the user name or password, then use the updated
settings in place of the default settings.
4. Specify binary mode by typing bin.
5. Specify the firmware’s path and filename with the put command. Type
put (path:filename).
The file will transfer and the PowerVault 35F will reboot. The PowerVault
35F is now using the new firmware.
NOTE: You may want to confirm the new firmware level by checking the
PowerVault 35F’s reboot messages through the serial interface.
TFTP Method
1. Make sure your PowerVault 35F is connected to a network and the IP
address is set properly.
2. At the command line, type the following tftp -i (IP address) put
(path:filename).
The file transfer process will begin. The PowerVault 35F will
automatically reboot upon completion of the download.
NOTE: You may want to confirm the new firmware level by checking the
PowerVault 35F’ s reboot messages through the serial interface.
Serial Port (Terminal Emulator)
NOTE: For quicker downloading, configure the PowerVault 35F and the
terminal emulator utility session connected to it (such as Hyperterminal)
to run at 115200.
1. Establish a Serial Connection to the PowerVault 35F. Refer to the
PowerVault 35F User’s Manual for the serial port settings.
2. From the Advanced Options menu, select the Download a new revision of
the Firmware command to start the download procedure.
3. When you confirm the download, the PowerVault 35F will start the
download process.
4. Use the Transfer -> Send File option in the terminal emulator utility.
5. Select the location of the firmware. Use the Browse button, if you
need help locating the firmware file.
6. Make sure you select XMODEM as the protocol.
7. Press the Send button.
8. The firmware will begin to download.
When the download is complete, the system verifies that the firmware image
was successfully written to the FLASH memory and then reboots the
PowerVault 35F. Upon reboot, the PowerVault 35F detects that there is a
newly downloaded firmware image and copies that image to the boot sector
of the FLASH and then boots with that image. At that point the PowerVault
35F is using the new firmware image.
The PowerVault 35F can either use FTP, TFTP or a serial connection (using
the XMODEM protocol) to update the firmware. In order to update the
firmware via the serial connection, the PowerVault 35F must be connected
to a terminal emulation program supporting XMODEM transfers. This menu
item does not appear when accessing the configuration menus through Telnet.
1. Download and run the file D9913D.EXE. This will extract the contents
of the archive to a temporary directory (i.e. x:\Dell\Drivers\PV35F\).
2. Decide the method for firmware download (FTP, TFTP, or Serial
Connection) and proceed to the appropriate instructions.
FTP Method
1. Make sure your PowerVault 35F is connected to a network and the IP
address is set properly.
2. Start your FTP program using the PowerVault 35F’ s IP address. Type
ftp (IP address).
NOTE: The default IP address is 1.1.1.1. See your PowerVault 35F User’s
Manual for instructions on changing the IP address.
3. Use root as the user name and password as the password.
NOTE: This is the default user name and password for the PowerVault 35F.
If you have changed the user name or password, then use the updated
settings in place of the default settings.
4. Specify binary mode by typing bin.
5. Specify the firmware’s path and filename with the put command. Type
put (path:filename).
The file will transfer and the PowerVault 35F will reboot. The PowerVault
35F is now using the new firmware.
NOTE: You may want to confirm the new firmware level by checking the
PowerVault 35F’s reboot messages through the serial interface.
TFTP Method
1. Make sure your PowerVault 35F is connected to a network and the IP
address is set properly.
2. At the command line, type the following tftp -i (IP address) put
(path:filename).
The file transfer process will begin. The PowerVault 35F will
automatically reboot upon completion of the download.
NOTE: You may want to confirm the new firmware level by checking the
PowerVault 35F’ s reboot messages through the serial interface.
Serial Port (Terminal Emulator)
NOTE: For quicker downloading, configure the PowerVault 35F and the
terminal emulator utility session connected to it (such as Hyperterminal)
to run at 115200.
1. Establish a Serial Connection to the PowerVault 35F. Refer to the
PowerVault 35F User’s Manual for the serial port settings.
2. From the Advanced Options menu, select the Download a new revision of
the Firmware command to start the download procedure.
3. When you confirm the download, the PowerVault 35F will start the
download process.
4. Use the Transfer -> Send File option in the terminal emulator utility.
5. Select the location of the firmware. Use the Browse button, if you
need help locating the firmware file.
6. Make sure you select XMODEM as the protocol.
7. Press the Send button.
8. The firmware will begin to download.
When the download is complete, the system verifies that the firmware image
was successfully written to the FLASH memory and then reboots the
PowerVault 35F. Upon reboot, the PowerVault 35F detects that there is a
newly downloaded firmware image and copies that image to the boot sector
of the FLASH and then boots with that image. At that point the PowerVault
35F is using the new firmware image.
Tutorial e guida ai driver
Per ulteriori download visitare Driver e download. Per aiuto sull'utilizzo delle informazioni presenti su questa pagina, visitare il sito Web Tutorial e Guida ai driver.