American Megatrends (AMI) PERC 2/SC, PERC2/DC, v.6.32.2.32, A00
自動インストール済み このファイルは、最新の更新プログラムの一部として自動的にインストールされました。問題が発生した場合は、手動でダウンロードして再インストールすることができます。このページのコンテンツは自動翻訳されている可能性があります。フィードバックを提供するには、ページの下部にあるフォームに入力してください。
PERC 2/SC-DC device driver for Windows Server 2003.
推奨
自動スキャンを使用するには、管理者としてWindowsにサインインしてください。すでに管理者としてサインインしていて、このメッセージが表示されている場合は、再起動してください。 お客様のシステムは貴社のIT管理者によって管理されおり、機能が制限されている可能性があります。
その他のアップデートを見る。SupportAssistを使用すると、お使いのデバイス向けの最新のドライバー アップデートをすべて見つけることができます。
修正と強化
Changes from 6.25
=================
1) Changes in the setup files, so that Scsiport driver should give the
correct device number and function number to the miniport driver.
2) A timeout is implemented in the driver so that driver shouldn't
wait infinitely for the firmware to acknowledge the interrupt.
3) The driver will return an error status for all the offline logical
drives.
4) Utilities are issuing 0xc3 calls for getting the logical drive
statistics. This is causing the system to crash. This bug has been
fixed in the driver.
5) The driver is using Hal functions to program hierarchy bridges
and SCSI chips when system goes to D3 standby state.
The use of Hal functions were not allowing the driver to pass
the HCT test. So we have to disable the Hal calls in the previous
releases. A workaround has been done in the driver whereby all the
Hal calls have been replaced by its assembly equivalent.
6) During reset, the driver was not clearing all the pending commands
whenever the firmware is not able to complete it.
7) Driver is allocating enough continuous memory for the
FLASH_WRITE_BLOCK(0x2c) command.
8) The system gives a blue screen when one swaps the boot controller.
This bug has been fixed by adding entries of all the supported
controllers in the critical data base section of the registry through
changes in the oemsetup.inf file.
9) The system was not waking up after a hibernation/standby operation.
This bug was caused by the driver. The driver was trying to access
PCI_CONFIG space from the ScsiRestartAdapter in the driver.
This bug has been fixed by accessing the PCI_CONFIG space from the
ScsiSetRunningConfig entry point.
10) A new command has been introduced to enhance the performance for
SCSI I/O on non-raid SCSI channel.
11) In case of standby, the driver was not waiting for the firmware
to get initialized. This resulted in the driver sending commands to
the firmware even when the firmware is not initialized. The fix has
been put in the driver. The driver is polling for the Firmware to
get initialized before sending any commands to the firmware.
詳細を見る=================
1) Changes in the setup files, so that Scsiport driver should give the
correct device number and function number to the miniport driver.
2) A timeout is implemented in the driver so that driver shouldn't
wait infinitely for the firmware to acknowledge the interrupt.
3) The driver will return an error status for all the offline logical
drives.
4) Utilities are issuing 0xc3 calls for getting the logical drive
statistics. This is causing the system to crash. This bug has been
fixed in the driver.
5) The driver is using Hal functions to program hierarchy bridges
and SCSI chips when system goes to D3 standby state.
The use of Hal functions were not allowing the driver to pass
the HCT test. So we have to disable the Hal calls in the previous
releases. A workaround has been done in the driver whereby all the
Hal calls have been replaced by its assembly equivalent.
6) During reset, the driver was not clearing all the pending commands
whenever the firmware is not able to complete it.
7) Driver is allocating enough continuous memory for the
FLASH_WRITE_BLOCK(0x2c) command.
8) The system gives a blue screen when one swaps the boot controller.
This bug has been fixed by adding entries of all the supported
controllers in the critical data base section of the registry through
changes in the oemsetup.inf file.
9) The system was not waking up after a hibernation/standby operation.
This bug was caused by the driver. The driver was trying to access
PCI_CONFIG space from the ScsiRestartAdapter in the driver.
This bug has been fixed by accessing the PCI_CONFIG space from the
ScsiSetRunningConfig entry point.
10) A new command has been introduced to enhance the performance for
SCSI I/O on non-raid SCSI channel.
11) In case of standby, the driver was not waiting for the firmware
to get initialized. This resulted in the driver sending commands to
the firmware even when the firmware is not initialized. The fix has
been put in the driver. The driver is polling for the Firmware to
get initialized before sending any commands to the firmware.
バージョン
6.32.2.32, A00
リリース日:
01 5月 2003
ダウンロード タイプ
ドライバ
カテゴリ
SCSI RAID
重要度
推奨デル・テクノロジーズでは、次に予定されているアップデート時に、このアップデートを適用することをお勧めします。このアップデートには、システム全体の正常性を維持するための変更が含まれています。これにより、システム ソフトウェアが最新の状態に保たれるとともに、システム ソフトウェアと他のシステム モジュール（ファームウェア、BIOS、ドライバー、ソフトウェア）との互換性が維持されます。また、その他の新機能が追加される場合もあります。
利用可能な形式
ファイル形式: MS Windows 32ビット用更新パッケージ
ファイル名: RAID-DRVR-R57743.exe
ファイルサイズ: 1.09 MB
これは大容量ファイルです。接続速度によっては、ダウンロードに時間がかかる場合があります。
フォーマットの説明:
Microsoft Windows 32ビット形式のDell Update Package（DUP）は、Microsoft Windows 64ビットオペレーティングシステム上でも実行できるように設計されています。Microsoft Windows 64ビット形式のDell Update Package（DUP）は、Microsoft Windows 64ビットオペレーティングシステム上でのみ実行できます。デバイスドライバのアップデートを選択するときは、お使いのオペレーティングシステムに適したものを選択してください。
ダウンロードの整合性を確認するには、チェックサムの値を検証してください。
MD5:
E0F3F8C4DA3D7411D3C530D342BE5D08
SHA1:
利用不可
SHA-256:
利用不可
ファイル形式: ローカルディスクに直接ファイルを解凍
ファイル名: PERC2-WS2K3-632A00.exe
ファイルサイズ: 95.44 KB
これは大容量ファイルです。接続速度によっては、ダウンロードに時間がかかる場合があります。
フォーマットの説明:
このファイル形式は、ハードドライブ上のディレクトリに解凍できるファイルのアーカイブです。このディレクトリからインストールを行うことができます。
ダウンロードの整合性を確認するには、チェックサムの値を検証してください。
MD5:
利用不可
SHA1:
利用不可
SHA-256:
利用不可
ダウンロードすることによって、Dellソフトウェア製品ライセンス契約 (英語で) の条項に同意したことになります。
サポート対象のオペレーティングシステム
Windows Server 2003
インストール手順
Custom Instructions for PERC2-WS2K3-632A00.exe:
This program creates a Windows 2000 driver diskette for the
controllers. You will need a formatted 3 1/2 inch floppy
diskette for the following procedure.
1) Download the file to a directory on your hard drive. The
file downloaded is a self extracting executable.
2) Double click on the file to run the executable.
3) Click on the unzip button to extract files to the floppy.
Power down the system and install the PERC/CERC card.
Configure the logical drives before proceeding with the
driver install described below.
Installing on a new driver on a Windows Server 2003 system
----------------------------------------------------------
1) Boot the system using the Windows Server 2003 CD.
As the message
"Press F6 if you need to install a third party SCSI or
RAID driver."
appears, press F6 immediately.
2) Within a few minutes, a screen appears that asks for
additional adapters in the system. Choose 'S'.
3) You are prompted for the driver diskette. Insert the
PERC/CERC Windows Server 2003 driver diskette in the floppy
drive and press Enter.
4) A list of drivers for PERC/CERC controllers appears.
Select the right driver for your installed controller and
press Enter to load the driver.
5) A statement is presented saying the driver that you provided
is older then the Windows driver.
Press 'S' to use the driver on the floppy.
6) Press Enter again to continue installation process as
usual.
Adding the PERC/CERC Driver to an Existing Windows Server 2003.
--------------------------------------------------------------
1) Boot the system to Windows 2003. The Found New Hardware
Wizard displays.
2) If you are installing the PERC 3/SC, PERC 4/DC PERC 4/SC,
PERC 4/DI or CERC ATA100/4CH, click on Next and
skip to step 5. Otherwise, click Cancel on all the new devices.
3) Restart the system from the shutdown menu.
4) The Found New Hardware Wizard displays again when the
system boots to Windows Server 2003. Click on Next.
5) Select Search for a suitable driver and click Next to
continue.
6) Select Floppy disk drive, insert the PERC/CERC Windows
2003 driver diskette created above and click Next to
continue.
7) Continue to click on Next and finish the installation.
8) The Found New Hardware Wizard screen appears one time for
each PERC 3/SC, PERC 4/SC, PERC 4/DC controller, three
times for each PERC 3/DC or PERC 3/DCL controller
and four times for each PERC 3/QC. Repeat steps 5 - 7 for each
time the wizard displays to complete installation of the card.
9) To confirm driver installation, right click on My
Computer and select Manage. Click on Device Manager, then
click on SCSI and RAID controllers to see the newly added
PERC 3 controller(s) in the list.
After finishing the driver update, YOU MUST REBOOT YOUR SERVER.
Updating the PERC/CERC Driver to an Existing Windows Server 2003.
------------------------------------------------------------------------
If your server is already running Windows Server 2003, use the
following steps
to update the PERC Windows Server 2003 driver.
1) Insert the PERC/CERC Windows Server 2003 driver diskette.
2) Position the mouse pointer on the my computer icon on your Start
Menu andright click and select Manage.
3) Position the mouse pointer on Device Manager and click the left
mouse
button .
4) Position the mouse pointer on SCSI and RAID controllers and double
click.
5) Select the PERC controller and double click.
6) Select the Driver tab
7) Select the Update Driver
The Upgrade Device Driver Wizard displays.
8) Select ”Install from a list of specific location” and click Next to
continue.
9) Select “Search for the best driver in these locations” and make sure
that the “search removable media (floppy, cd-rom,…)” option is
checked. Then click on the Next but
This program creates a Windows 2000 driver diskette for the
controllers. You will need a formatted 3 1/2 inch floppy
diskette for the following procedure.
1) Download the file to a directory on your hard drive. The
file downloaded is a self extracting executable.
2) Double click on the file to run the executable.
3) Click on the unzip button to extract files to the floppy.
Power down the system and install the PERC/CERC card.
Configure the logical drives before proceeding with the
driver install described below.
Installing on a new driver on a Windows Server 2003 system
----------------------------------------------------------
1) Boot the system using the Windows Server 2003 CD.
As the message
"Press F6 if you need to install a third party SCSI or
RAID driver."
appears, press F6 immediately.
2) Within a few minutes, a screen appears that asks for
additional adapters in the system. Choose 'S'.
3) You are prompted for the driver diskette. Insert the
PERC/CERC Windows Server 2003 driver diskette in the floppy
drive and press Enter.
4) A list of drivers for PERC/CERC controllers appears.
Select the right driver for your installed controller and
press Enter to load the driver.
5) A statement is presented saying the driver that you provided
is older then the Windows driver.
Press 'S' to use the driver on the floppy.
6) Press Enter again to continue installation process as
usual.
Adding the PERC/CERC Driver to an Existing Windows Server 2003.
--------------------------------------------------------------
1) Boot the system to Windows 2003. The Found New Hardware
Wizard displays.
2) If you are installing the PERC 3/SC, PERC 4/DC PERC 4/SC,
PERC 4/DI or CERC ATA100/4CH, click on Next and
skip to step 5. Otherwise, click Cancel on all the new devices.
3) Restart the system from the shutdown menu.
4) The Found New Hardware Wizard displays again when the
system boots to Windows Server 2003. Click on Next.
5) Select Search for a suitable driver and click Next to
continue.
6) Select Floppy disk drive, insert the PERC/CERC Windows
2003 driver diskette created above and click Next to
continue.
7) Continue to click on Next and finish the installation.
8) The Found New Hardware Wizard screen appears one time for
each PERC 3/SC, PERC 4/SC, PERC 4/DC controller, three
times for each PERC 3/DC or PERC 3/DCL controller
and four times for each PERC 3/QC. Repeat steps 5 - 7 for each
time the wizard displays to complete installation of the card.
9) To confirm driver installation, right click on My
Computer and select Manage. Click on Device Manager, then
click on SCSI and RAID controllers to see the newly added
PERC 3 controller(s) in the list.
After finishing the driver update, YOU MUST REBOOT YOUR SERVER.
Updating the PERC/CERC Driver to an Existing Windows Server 2003.
------------------------------------------------------------------------
If your server is already running Windows Server 2003, use the
following steps
to update the PERC Windows Server 2003 driver.
1) Insert the PERC/CERC Windows Server 2003 driver diskette.
2) Position the mouse pointer on the my computer icon on your Start
Menu andright click and select Manage.
3) Position the mouse pointer on Device Manager and click the left
mouse
button .
4) Position the mouse pointer on SCSI and RAID controllers and double
click.
5) Select the PERC controller and double click.
6) Select the Driver tab
7) Select the Update Driver
The Upgrade Device Driver Wizard displays.
8) Select ”Install from a list of specific location” and click Next to
continue.
9) Select “Search for the best driver in these locations” and make sure
that the “search removable media (floppy, cd-rom,…)” option is
checked. Then click on the Next but