PowerConnect、M8024S、M8024、4.2.0.4、A24

Fixes and Enhancement:

Fixes
- PowerConnect sFlow implementation is not per specification Enhancements
- Using config wizard to setup 8024 causes iscsi error messages off out-of-band in console
- 8024 stack does not follow similar banner execution for console, telnet and ssh
- Simple Switch should have FC enabled by default
- OSPF error message after reboot
- show crypto key mypubkey generates two error messages
- Web GUI ARP table does not match the CLI ARP table
- The copper auto negotiation process fails at 100mb FD and fails to link up
- PCM6220 - Wrong information for current link status in port configuration page on the GUI
- PC8024 - VLAN membership change on interface affects unrelated interface
- Implement dot1qVlanStaticTable in M8024-K
- Trunk mode native vlan implementation not compatible with Cisco
- PCM6220 - Switch hangs when user tries to transfer a file from the flash to the server using sftp
- No message logged for "Max number of SSH login sessions exceeded"
- CLI command "show ipv6 interface" does not paginate correctly
- 2nd and 4th block of copper ports 5-8 and 13-16 think they are fiber ports, possible problems
- WebGui Secure Shell SSH Remote Access
- Web UI MSTP Instance pull down menu displays 4k MSTIs
- Flowcontrol negotiation issues with 10GBase-T module
- PC8024 - GUI - Under Port Configuration page get error on 10GB ports when you change any setting
- Unable to config secure ssh from web interface. error 'sshcfg_load start' missing pops up
- Web interface fails to provide an iSCSI web page when selecting the iSCSI item.
- Line "no passive-interface Vl32" in startup-config does not get loaded on startup
- Web GUI Admin Duplex setting on 10G Fiber ports
- Advertise LLDP Management Address as IP Address assigned to OOB interface
- PCM6348 - Log message output
- Firmware missing port VLAN membership in the GUI
- M8024 - 1GB link being negotiated on 10GB Intel X520-KX4
- Feature request - Display "client-DUID" in DHCP binding table.
-clock summer-time recurring EU offset 60 zone "GMT" not offsetting the time by 60 minutes
- M6220 - Simple mode, VLAN setting not active when move port to another group
- SSH configuration not restored after reboot
- PC8024 - VLAN trunk assignment CLI change
- Web UI displays incorrect session timeout duration
- PC8024 - Secure HTTP Random Characters - 4.1.0.6
- Upgrades to 4.1.0.9 are causing network outages. The wizard from 4.1.0.9 fails to setup interfaces
- PC6220M GUI shows stack-ports down but CLI does not. In previous version issue didn't exist
- M6220 - Routing fails on VLAN
- MIB walk crashes switch
- M8024 - No password min length error using web GUI
- Bug in Simple Switch GUI.
- M6348 simple mode issue with 10G ports in aggregator group
- Banner motd configuration changes after reload.
- Error message via Web UI refers to "Management VLAN"
- Web UI not generating error for out bound ACL & applies the config.
- Auto-neg option via Web UI is not grayed out for 10Gb fiber ports.
- CLI command "show interface detail port-channel1" locks up console session
- Creating VLANs, assigning ports using vlan membership detail page causes removal from running-config
- Assigning ACL Priority to a VLAN interface does not get set via Web UI
- Incorrect Model numbers and revision date in dellref.my

Enhancements
- DCBx on M8024-k/8024/8024F
- FIP Snooping Bridge on M8024-k/8024/8024F
- Add EEE Support for the PC7000 10GBaseT Ports
- GUI EEE Power Savings Charts
- RP Failover Performance Improvement
- Flexible Dynamic LAG Limits
- CLI Help Usability Improvements
- Ability to Show Static Route Entries
- CMC XML Support
- Stacking Over Ethernet Ports
- Change Dell EqualLogic iSCSI Auto Detect to default
- Add CLI Macro (Port Profile) for Dell Compellent Storage Equipment
- Provide Dell EqualLogic DCBx TLV Auto Detect and Configuration on M8024-k/8024/8024F.