LSI Logic PERC 4/Di, v.1.18c, A03
자동 설치 완료 이 파일은 최근 업데이트의 일부로 자동으로 설치되었습니다. 문제가 발생하는 경우 수동으로 다운로드하고 재설치할 수 있습니다.이 페이지의 콘텐츠는 자동으로 번역되었을 수 있습니다. 피드백을 제공하려면 페이지 하단에 있는 양식을 작성하십시오.
PERC 4/Di Device Driver for Red Hat Linux 7.2.
권장 사항
자동 스캔을 사용하려면 관리자 권한으로 Windows에 로그인하십시오. 관리자 권한으로 이미 로그인한 상태에서 이 메시지가 표시되었다면 재부팅하시기 바랍니다. 시스템이 IT 관리자에 의해 관리되고 있으며, 기능이 제한될 수 있습니다.
추가 업데이트 사항을 찾습니다. SupportAssist를 사용하여 디바이스에 대한 모든 최신 드라이버 업데이트를 찾습니다.
수정 또는 개선한 내용
Not Applicable
자세히 보기버전
1.18c, A03
출시일
13 8월 2002
다운로드 유형
드라이버
범주
SCSI RAID
중요도
옵션Dell Technologies는 이 업데이트를 검토하여 시스템에 대한 적용 여부를 판단할 것을 고객에게 권장합니다. 이 업데이트에는 특정 구성에 대해서만 영향을 미치는 변경 사항이 포함되어 있거나 해당 시스템 환경에 적용될 수도 있는 새 기능이 포함되어 있습니다.
사용 가능한 형식
파일 형식: 로컬 디스크로 직접 파일 압축 해제
파일 이름: perc4di-118c-72c.tar.gz
파일 크기: 538.62 KB
대용량 파일입니다. 인터넷 속도에 따라 다운로드하는 데 일정 시간이 소요될 수 있습니다.
형식 설명:
이 파일 포맷은 하드 드라이브의 디렉토리로 압축 해제할 수 있는 파일의 아카이브로 구성됩니다. 설치는 그 이후 해당 디렉토리에서 수행할 수 있습니다.
다운로드의 무결성을 보장하려면 체크섬 값을 확인하십시오.
MD5:
이용 불가
SHA1:
이용 불가
SHA-256:
이용 불가
다운로드할 경우 Dell 소프트웨어 라이센스 계약 (영어로) 에 동의하는 것으로 간주합니다.
지원되는 운영 체제
Red Hat® Linux 7.2
설치 방법
Instructions for downloading and creating driver diskette:
----------------------------------------------------------
You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
Download the file PERC4di-118c-72c.tar.gz to a temporary directory on your working system.
Extract the file to the floppy disk as follows:
1. On a Linux system:
Type the following commands under a Linux command shell:
mount /dev/fd0 /mnt/floppy
tar xvzf -C /mnt/floppy
(Eg: /temp/PERC4di-118c-72c.tar.gz)
umount /mnt/floppy
2. On a Microsoft Windows system:
You can use Winzip to extract tar.gz archives. However,
note the following settings under Winzip to ensure correct
extraction of the files.
Start Winzip -> Go to Options -> Configuration
Under the Miscellaneous tab make sure "TAR file smart
CR/LF conversion" is unchecked.
Upon opening the tar.gz archive with Winzip, you get the
following prompt:
'Archive contains one file. Should Winzip decompress it to
a temporary folder and open it?'
Press 'yes' and extract the files normally under Winzip to
the floppy drive.
Install Red Hat Linux 7.2 driver for PERC 4/Di as a boot controller
-------------------------------------------------------
There are two ways of installing Red Hat 7.2 driver onto the
PERC 4/Di as a boot controller. One is using a driver disk during
OS installation and the second is using a driver (megaraid) RPM to update
driver after OS is installed. The steps for both of these methods are
provided below. All the files needed for both methods are included in the
driver diskette created above.
For more detailed installation instructions of Red Hat 7.2, please refer
to the OS installation guide at http://www.dell.com/linux.
I. Installing driver during OS installation:
--------------------------------------------
1. Boot normally from the Redhat installation CD-Rom.
2. Type 'linux dd' on the boot prompt.
3. When the install prompts for a driver disk, insert the
driver diskette created above and press 'Enter'.
4. Installation progresses normally. Continue until the
'Create Bootdisk' screen. Press CTRL-ALT-F2 to get to a
shell window and type the following commands:
chroot /mnt/sysimage
cd /boot
/sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10
lilo ( only if lilo was used as bootloader. If grub used - skip this step )
exit
Press CTRL-ALT-F7 to get back to the install screen.
5. Complete the installation as directed by the install.
II. Update driver using RPMs after OS is installed
--------------------------------------------------
Type the following commands under a Linux command shell:
mount /dev/fd0 /mnt/floppy
cd /mnt/floppy
./megarpmwrapper.sh
Than follow the on-screen instructions to install the RPM driver.
For more detailed information about the script megarpmwrapper.sh,
please refer to the release_notes.txt included in the release.
----------------------------------------------------------
You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
Download the file PERC4di-118c-72c.tar.gz to a temporary directory on your working system.
Extract the file to the floppy disk as follows:
1. On a Linux system:
Type the following commands under a Linux command shell:
mount /dev/fd0 /mnt/floppy
tar xvzf -C /mnt/floppy
(Eg: /temp/PERC4di-118c-72c.tar.gz)
umount /mnt/floppy
2. On a Microsoft Windows system:
You can use Winzip to extract tar.gz archives. However,
note the following settings under Winzip to ensure correct
extraction of the files.
Start Winzip -> Go to Options -> Configuration
Under the Miscellaneous tab make sure "TAR file smart
CR/LF conversion" is unchecked.
Upon opening the tar.gz archive with Winzip, you get the
following prompt:
'Archive contains one file. Should Winzip decompress it to
a temporary folder and open it?'
Press 'yes' and extract the files normally under Winzip to
the floppy drive.
Install Red Hat Linux 7.2 driver for PERC 4/Di as a boot controller
-------------------------------------------------------
There are two ways of installing Red Hat 7.2 driver onto the
PERC 4/Di as a boot controller. One is using a driver disk during
OS installation and the second is using a driver (megaraid) RPM to update
driver after OS is installed. The steps for both of these methods are
provided below. All the files needed for both methods are included in the
driver diskette created above.
For more detailed installation instructions of Red Hat 7.2, please refer
to the OS installation guide at http://www.dell.com/linux.
I. Installing driver during OS installation:
--------------------------------------------
1. Boot normally from the Redhat installation CD-Rom.
2. Type 'linux dd' on the boot prompt.
3. When the install prompts for a driver disk, insert the
driver diskette created above and press 'Enter'.
4. Installation progresses normally. Continue until the
'Create Bootdisk' screen. Press CTRL-ALT-F2 to get to a
shell window and type the following commands:
chroot /mnt/sysimage
cd /boot
/sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10
lilo ( only if lilo was used as bootloader. If grub used - skip this step )
exit
Press CTRL-ALT-F7 to get back to the install screen.
5. Complete the installation as directed by the install.
II. Update driver using RPMs after OS is installed
--------------------------------------------------
Type the following commands under a Linux command shell:
mount /dev/fd0 /mnt/floppy
cd /mnt/floppy
./megarpmwrapper.sh
Than follow the on-screen instructions to install the RPM driver.
For more detailed information about the script megarpmwrapper.sh,
please refer to the release_notes.txt included in the release.