Dell MD3000i 싱글 컨트롤러 교체 유틸리티, A02
자동 설치 완료 이 파일은 최근 업데이트의 일부로 자동으로 설치되었습니다. 문제가 발생하는 경우 수동으로 다운로드하고 재설치할 수 있습니다.이 페이지의 콘텐츠는 자동으로 번역되었을 수 있습니다. 피드백을 제공하려면 페이지 하단에 있는 양식을 작성하십시오.
MD3000i Single Controller Replacement Utility: This utility updates the firmware and NVSRAM of a replacement controller for an MD3000i in single controller configuration to match the version on the array.
권장 사항
추가 업데이트 사항을 찾습니다. SupportAssist를 사용하여 디바이스에 대한 모든 최신 드라이버 업데이트를 찾습니다.
수정 또는 개선한 내용
Provides support for second generation firmware.
Additionally, a serial cable is no longer required to use the utility.
자세히 보기Additionally, a serial cable is no longer required to use the utility.
버전
A02, A02
출시일
19 12월 2008
다운로드 유형
유틸리티
범주
시스템 유틸리티
중요도
옵션Dell Technologies는 이 업데이트를 검토하여 시스템에 대한 적용 여부를 판단할 것을 고객에게 권장합니다. 이 업데이트에는 특정 구성에 대해서만 영향을 미치는 변경 사항이 포함되어 있거나 해당 시스템 환경에 적용될 수도 있는 새 기능이 포함되어 있습니다.
파일 형식: 로컬 디스크로 직접 파일 압축 해제
파일 이름: SCRUtilityA02.zip
파일 크기: 95.17 MB
대용량 파일입니다. 인터넷 속도에 따라 다운로드하는 데 일정 시간이 소요될 수 있습니다.
형식 설명:
이 파일 포맷은 하드 드라이브의 디렉토리로 압축 해제할 수 있는 파일의 아카이브로 구성됩니다. 설치는 그 이후 해당 디렉토리에서 수행할 수 있습니다.
다운로드의 무결성을 보장하려면 체크섬 값을 확인하십시오.
MD5:
cb0a77bed058612701dd191c612e7ae4
SHA1:
이용 불가
SHA-256:
이용 불가
다운로드할 경우 Dell 소프트웨어 라이센스 계약 (영어로) 에 동의하는 것으로 간주합니다.
Custom Instructions for SCRUtilityA02.zip:
The utility can be run from any computer with access to the management port of the storage array by following these steps:
1. Extract all files and folders from the utility .zip file to a temporary location.
2. Navigate to the location of the extracted files.
If you are using a Windows system, run the simplex.bat file.
If you are using a Linux system, execute the simplex.sh file.
A GUI-based wizard will guide you through the remaining steps necessary to update the controller.
3. When the wizard completes, click Finish.
The utility can be run from any computer with access to the management port of the storage array by following these steps:
1. Extract all files and folders from the utility .zip file to a temporary location.
2. Navigate to the location of the extracted files.
If you are using a Windows system, run the simplex.bat file.
If you are using a Linux system, execute the simplex.sh file.
A GUI-based wizard will guide you through the remaining steps necessary to update the controller.
3. When the wizard completes, click Finish.