Dell PowerVault 35F, D9908E
자동 설치 완료 이 파일은 최근 업데이트의 일부로 자동으로 설치되었습니다. 문제가 발생하는 경우 수동으로 다운로드하고 재설치할 수 있습니다.이 페이지의 콘텐츠는 자동으로 번역되었을 수 있습니다. 피드백을 제공하려면 페이지 하단에 있는 양식을 작성하십시오.
PowerVault 35F firmware version d9908e.
권장 사항
추가 업데이트 사항을 찾습니다. SupportAssist를 사용하여 디바이스에 대한 모든 최신 드라이버 업데이트를 찾습니다.
버전
d9908e, D9908E
출시일
06 2월 2001
다운로드 유형
펌웨어
범주
파이버 채널
중요도
옵션Dell Technologies는 이 업데이트를 검토하여 시스템에 대한 적용 여부를 판단할 것을 고객에게 권장합니다. 이 업데이트에는 특정 구성에 대해서만 영향을 미치는 변경 사항이 포함되어 있거나 해당 시스템 환경에 적용될 수도 있는 새 기능이 포함되어 있습니다.
파일 형식: 자동 압축 해제 zip 내부의 하나 이상의 자동 압축 해제 디스크 이미지
파일 이름: D9908E.exe
파일 크기: 553 KB
대용량 파일입니다. 인터넷 속도에 따라 다운로드하는 데 일정 시간이 소요될 수 있습니다.
형식 설명:
이 파일에는 압축된 파일 세트가 있습니다. 파일을 하드 드라이브의 폴더로 다운로드한 다음 두 번 클릭하여 파일 세트를 압축 해제합니다. 지침에 따라 설치를 완료합니다.
다운로드의 무결성을 보장하려면 체크섬 값을 확인하십시오.
MD5:
af7f581a2ef46319201864a1164038a7
SHA1:
이용 불가
SHA-256:
이용 불가
다운로드할 경우 Dell 소프트웨어 라이센스 계약 (영어로) 에 동의하는 것으로 간주합니다.
PowerVault 35F Firmware Download Instructions
The PowerVault 35F can either use FTP, TFTP or a serial connection
(using the XMODEM protocol) to update the firmware. In order to
update the firmware via the serial connection, the PowerVault 35F
must be connected to a terminal emulation program supporting
XMODEM transfers. This menu item does not appear when accessing
the configuration menus through Telnet.
To download firmware using FTP:
1. Connect your computer to the PowerVault 35F’ s Ethernet port.
2. Start your FTP program using the PowerVault 35F’ s IP address:
ftp
Note: The default IP address is 1.1.1.1. See the Change IP
Address section of this chapter for information on changing
the PowerVault 35F IP address.
3. Use root as the user name and password as the password.
To change the user name and password, see the Change Security
Settings section of this chapter.
4. Specify binary mode:
bin
5. Specify the firmware’s path and filename with the put command:
put
The file will transfer and the PowerVault 35F will reboot. The
PowerVault 35F is now using the new firmware.
NOTE: You may want to confirm the new firmware level by
checking the PowerVault 35F’s reboot messages through the
serial interface.
To download firmware using TFTP:
1. Connect your computer using the PowerVault 35F’s
Ethernet port.
2. At the command line, type the following command:
tftp -i put
The file will tranfer and the PowerVault 35F will
reboot. The PowerVault 35F is now using the new
firmware.
NOTE: You may want to confirm the new firmware level by
checking the PowerVault 35F’ s reboot messages through
the serial interface.
To download firmware using a terminal emulator:
NOTE: For quicker downloading, configure the PowerVault 35F
and the terminal emulator utility session connected to it
(such as Hyperterminal) to run at 115200.
1. Establish a Serial Connection to the PowerVault 35F.
2. From the Advanced Options menu, select the Download a
new revision of the Firmware command to start the download
procedure.
3. When you confirm you want to download, the PowerVault 35F
will start the download process.
4. Use the Transfer® Send File option in the terminal emulator
utility.
5. Select the location of the firmware. Use the Browse button,
if you need help finding it.
6. Make sure you select XMODEM as the protocol.
7. Press the Send button.
8. The firmware will begin to download.
When the download is complete, the system verifies that the
firmware image was successfully written to the FLASH memory and
then reboots the PowerVault 35F. Upon reboot, the PowerVault 35F
detects that there is a newly downloaded firmware image and
copies that image to the boot sector of the FLASH and then boots
with that image. At that point the PowerVault 35F is using the
new firmware image.
The PowerVault 35F can either use FTP, TFTP or a serial connection
(using the XMODEM protocol) to update the firmware. In order to
update the firmware via the serial connection, the PowerVault 35F
must be connected to a terminal emulation program supporting
XMODEM transfers. This menu item does not appear when accessing
the configuration menus through Telnet.
To download firmware using FTP:
1. Connect your computer to the PowerVault 35F’ s Ethernet port.
2. Start your FTP program using the PowerVault 35F’ s IP address:
ftp
Note: The default IP address is 1.1.1.1. See the Change IP
Address section of this chapter for information on changing
the PowerVault 35F IP address.
3. Use root as the user name and password as the password.
To change the user name and password, see the Change Security
Settings section of this chapter.
4. Specify binary mode:
bin
5. Specify the firmware’s path and filename with the put command:
put
The file will transfer and the PowerVault 35F will reboot. The
PowerVault 35F is now using the new firmware.
NOTE: You may want to confirm the new firmware level by
checking the PowerVault 35F’s reboot messages through the
serial interface.
To download firmware using TFTP:
1. Connect your computer using the PowerVault 35F’s
Ethernet port.
2. At the command line, type the following command:
tftp -i
The file will tranfer and the PowerVault 35F will
reboot. The PowerVault 35F is now using the new
firmware.
NOTE: You may want to confirm the new firmware level by
checking the PowerVault 35F’ s reboot messages through
the serial interface.
To download firmware using a terminal emulator:
NOTE: For quicker downloading, configure the PowerVault 35F
and the terminal emulator utility session connected to it
(such as Hyperterminal) to run at 115200.
1. Establish a Serial Connection to the PowerVault 35F.
2. From the Advanced Options menu, select the Download a
new revision of the Firmware command to start the download
procedure.
3. When you confirm you want to download, the PowerVault 35F
will start the download process.
4. Use the Transfer® Send File option in the terminal emulator
utility.
5. Select the location of the firmware. Use the Browse button,
if you need help finding it.
6. Make sure you select XMODEM as the protocol.
7. Press the Send button.
8. The firmware will begin to download.
When the download is complete, the system verifies that the
firmware image was successfully written to the FLASH memory and
then reboots the PowerVault 35F. Upon reboot, the PowerVault 35F
detects that there is a newly downloaded firmware image and
copies that image to the boot sector of the FLASH and then boots
with that image. At that point the PowerVault 35F is using the
new firmware image.