Dell PowerVault 224F/660F SES Firmware, v. 1.9.5, A01
자동 설치 완료 이 파일은 최근 업데이트의 일부로 자동으로 설치되었습니다. 문제가 발생하는 경우 수동으로 다운로드하고 재설치할 수 있습니다.이 페이지의 콘텐츠는 자동으로 번역되었을 수 있습니다. 피드백을 제공하려면 페이지 하단에 있는 양식을 작성하십시오.
SES 1.9.5 Test Release Notes
The SES195.bin file is the required file for the download. It is highly
recommended that all I/O is stopped before beginning this procedure.
You must update the SES firmware on each LS module in the PowerVault 660
and each of the attached enclosures. This includes the 660F as well as all
attached 224F enclosures.
If you are replacing an LS module, or adding new PowerVault 224 units to
an existing subsystem, you should update all LS modules with this firmware.
Enclosure services must be online to update the firmware. If enclosure
services are offline then restore them to the online state before
performing the following procedure.
The SES195.bin file is the required file for the download. It is highly
recommended that all I/O is stopped before beginning this procedure.
You must update the SES firmware on each LS module in the PowerVault 660
and each of the attached enclosures. This includes the 660F as well as all
attached 224F enclosures.
If you are replacing an LS module, or adding new PowerVault 224 units to
an existing subsystem, you should update all LS modules with this firmware.
Enclosure services must be online to update the firmware. If enclosure
services are offline then restore them to the online state before
performing the following procedure.
권장 사항
자동 스캔을 사용하려면 관리자 권한으로 Windows에 로그인하십시오. 관리자 권한으로 이미 로그인한 상태에서 이 메시지가 표시되었다면 재부팅하시기 바랍니다. 시스템이 IT 관리자에 의해 관리되고 있으며, 기능이 제한될 수 있습니다.
추가 업데이트 사항을 찾습니다. SupportAssist를 사용하여 디바이스에 대한 모든 최신 드라이버 업데이트를 찾습니다.
수정 또는 개선한 내용
Improvements to SES 1.9.5
SES 1.9.5 enhances the communication between SES modules. In the past
there were times when thresholds set on the master SES were not copied to
the slave SES. In a failover scenario the slave would apply the old
values, requiring that the user reset the new thresholds.
SES 1.9.5 enhances reporting so that when an LS module fails, Dell Open
Manage Array Manager can report the problem. The LED for the LS module
will, as in previous versions, still light when an LS module is in a
failed state.
SES 1.9.5 now reports the correct model name of the system, either PV660
or PV224.
In SES 1.3b2, upper warning/critical for LS Module temperature sensors is
45C/55C and for power supply sensors is 55C/65C, which is incorrect. The
correct settings are in SES 1.9.5 and are 35C/45C for the LS module
temperature sensors and 45C/55C for the power supply.
자세히 보기SES 1.9.5 enhances the communication between SES modules. In the past
there were times when thresholds set on the master SES were not copied to
the slave SES. In a failover scenario the slave would apply the old
values, requiring that the user reset the new thresholds.
SES 1.9.5 enhances reporting so that when an LS module fails, Dell Open
Manage Array Manager can report the problem. The LED for the LS module
will, as in previous versions, still light when an LS module is in a
failed state.
SES 1.9.5 now reports the correct model name of the system, either PV660
or PV224.
In SES 1.3b2, upper warning/critical for LS Module temperature sensors is
45C/55C and for power supply sensors is 55C/65C, which is incorrect. The
correct settings are in SES 1.9.5 and are 35C/45C for the LS module
temperature sensors and 45C/55C for the power supply.
버전
1.9.5, A01
출시일
20 9월 2001
다운로드 유형
펌웨어
범주
파이버 채널
중요도
옵션Dell Technologies는 이 업데이트를 검토하여 시스템에 대한 적용 여부를 판단할 것을 고객에게 권장합니다. 이 업데이트에는 특정 구성에 대해서만 영향을 미치는 변경 사항이 포함되어 있거나 해당 시스템 환경에 적용될 수도 있는 새 기능이 포함되어 있습니다.
사용 가능한 형식
파일 형식: 로컬 디스크로 직접 파일 압축 해제
파일 이름: SES_195.exe
파일 크기: 115.92 KB
대용량 파일입니다. 인터넷 속도에 따라 다운로드하는 데 일정 시간이 소요될 수 있습니다.
형식 설명:
이 파일 포맷은 하드 드라이브의 디렉토리로 압축 해제할 수 있는 파일의 아카이브로 구성됩니다. 설치는 그 이후 해당 디렉토리에서 수행할 수 있습니다.
다운로드의 무결성을 보장하려면 체크섬 값을 확인하십시오.
MD5:
이용 불가
SHA1:
이용 불가
SHA-256:
이용 불가
다운로드할 경우 Dell 소프트웨어 라이센스 계약 (영어로) 에 동의하는 것으로 간주합니다.
지원되는 운영 체제
해당 없음
설치 방법
To update the LS module SES firmware, perform the following steps:
1. Start Array Manager on the host system by clicking Start-- Programs--
Dell
OpenManage Applications-- Array Manager-- Array Manager Console.
2. Update the SES firmware on the PowerVault 660F.
a. Click Arrays-- PV660F SubSystem-- Physical Array.
b. Right-click the controller for the subsystem you wish to upgrade and
choose Download-- SES Firmware.
c. Select all the enclosure check boxes and click Next.
d. Click Browse and locate the SES195.bin file. Click Next.
e. Click Finish and OK.
NOTE: This process takes about 8 to 9 minutes for each additional LS
module in
the storage array. If the firmware update does not complete successfully,
repeat
the process until it does. This issue is not a hardware problem, but a
software-timing
issue.
f. After download completes, right-click the PV660F subsystem in Array
Manager and choose Rescan to update the properties information.
g. Right-click the enclosure in Array Manager, choose Properties, and
verify that it is using SES firmware version 1.9.5. If it is not, repeat
the download procedure.
h. Physically remove the primary LS module to cause failover.
i. Right-click the PV660F subsystem in Array Manager and choose Rescan
to update the properties information.
j. Right-click the enclosure and choose Properties to verify its
firmware level is also at version 1.9.5. If it is not, repeat the
download procedure.
k. Replace the LS module that you removed. If you have multiple
enclosures, you must verify the firmware level on every LS module
in the subsystem, one at a time.
1. Start Array Manager on the host system by clicking Start-- Programs--
Dell
OpenManage Applications-- Array Manager-- Array Manager Console.
2. Update the SES firmware on the PowerVault 660F.
a. Click Arrays-- PV660F SubSystem-- Physical Array.
b. Right-click the controller for the subsystem you wish to upgrade and
choose Download-- SES Firmware.
c. Select all the enclosure check boxes and click Next.
d. Click Browse and locate the SES195.bin file. Click Next.
e. Click Finish and OK.
NOTE: This process takes about 8 to 9 minutes for each additional LS
module in
the storage array. If the firmware update does not complete successfully,
repeat
the process until it does. This issue is not a hardware problem, but a
software-timing
issue.
f. After download completes, right-click the PV660F subsystem in Array
Manager and choose Rescan to update the properties information.
g. Right-click the enclosure in Array Manager, choose Properties, and
verify that it is using SES firmware version 1.9.5. If it is not, repeat
the download procedure.
h. Physically remove the primary LS module to cause failover.
i. Right-click the PV660F subsystem in Array Manager and choose Rescan
to update the properties information.
j. Right-click the enclosure and choose Properties to verify its
firmware level is also at version 1.9.5. If it is not, repeat the
download procedure.
k. Replace the LS module that you removed. If you have multiple
enclosures, you must verify the firmware level on every LS module
in the subsystem, one at a time.