BIOS 업데이트 중 컴퓨터의 전원을 끄거나 전원에서 분리하면 컴퓨터에 손상을 줄 수 있습니다. 업데이트하는 동안 컴퓨터가 재시작되고 잠시 검은색 화면이 표시될 수 있습니다.
업데이트하기 전에 설치 지침 및 아래에 설명된 중요 정보를 읽으십시오.
Dell OptiPlex System BIOS, A06
자동 설치 완료 이 파일은 최근 업데이트의 일부로 자동으로 설치되었습니다. 문제가 발생하는 경우 수동으로 다운로드하고 재설치할 수 있습니다.이 페이지의 콘텐츠는 자동으로 번역되었을 수 있습니다. 피드백을 제공하려면 페이지 하단에 있는 양식을 작성하십시오.
Optiplex GX50 A06 FlashBIOS
권장 사항
자동 스캔을 사용하려면 관리자 권한으로 Windows에 로그인하십시오. 관리자 권한으로 이미 로그인한 상태에서 이 메시지가 표시되었다면 재부팅하시기 바랍니다. 시스템이 IT 관리자에 의해 관리되고 있으며, 기능이 제한될 수 있습니다.
추가 업데이트 사항을 찾습니다. SupportAssist를 사용하여 디바이스에 대한 모든 최신 드라이버 업데이트를 찾습니다.
수정 또는 개선한 내용
The following changes have been made to the A04 to create A06 (A05 was not
released from Development):
* Adjusted USB Emulation support for special keys, and non-US keyboards.
* Added IDE UDMA support to speed up resume from Hibernate (when enabled).
* Added support for new Processors.
* Added support for additional models in the GX50 Series.
* Reduce POST time when no PS/2 keyboard or Mouse installed.
* Fixed issues with some USB devices causing a keyboard POST error with a
USB keyboard.
* Added two new diagnostic LED codes for better memory failure isolation.
No Memory Detected (ABCD=Grn, Yel, Yel, Yel)
Memory Configuration Failure (ABCD=Grn, Yel, Grn, Yel)
* Fixed false error on Floppy Drive when running Diags From Bootable Diags
CD without a Floppy Drive.
* Fixed possible CMOS corruption when adjusting system configuration
through Open Manage.
* Allow Num-pad Enter key on boot menu screen.
* Changed the AC Power Recovery to OFF as default.
* Added "Low Power Mode" option to System Setup.
* Fixed issue with UNKNOWN devices in System Setup for IDE devices.
If a failure occurs, now check the second IDE cable for devices.
* Fixed hang problem with Creative Audigy and large sound samples.
* Fixed issue when resuming from Hibernate with keyboard & mouse swapped.
자세히 보기released from Development):
* Adjusted USB Emulation support for special keys, and non-US keyboards.
* Added IDE UDMA support to speed up resume from Hibernate (when enabled).
* Added support for new Processors.
* Added support for additional models in the GX50 Series.
* Reduce POST time when no PS/2 keyboard or Mouse installed.
* Fixed issues with some USB devices causing a keyboard POST error with a
USB keyboard.
* Added two new diagnostic LED codes for better memory failure isolation.
No Memory Detected (ABCD=Grn, Yel, Yel, Yel)
Memory Configuration Failure (ABCD=Grn, Yel, Grn, Yel)
* Fixed false error on Floppy Drive when running Diags From Bootable Diags
CD without a Floppy Drive.
* Fixed possible CMOS corruption when adjusting system configuration
through Open Manage.
* Allow Num-pad Enter key on boot menu screen.
* Changed the AC Power Recovery to OFF as default.
* Added "Low Power Mode" option to System Setup.
* Fixed issue with UNKNOWN devices in System Setup for IDE devices.
If a failure occurs, now check the second IDE cable for devices.
* Fixed hang problem with Creative Audigy and large sound samples.
* Fixed issue when resuming from Hibernate with keyboard & mouse swapped.
버전
A06, A06
출시일
20 8월 2002
다운로드 유형
시스템 BIOS
범주
BIOS
중요도
옵션Dell Technologies는 이 업데이트를 검토하여 시스템에 대한 적용 여부를 판단할 것을 고객에게 권장합니다. 이 업데이트에는 특정 구성에 대해서만 영향을 미치는 변경 사항이 포함되어 있거나 해당 시스템 환경에 적용될 수도 있는 새 기능이 포함되어 있습니다.
사용 가능한 형식
파일 형식: 자동 압축 해제 zip 내부의 하나 이상의 자동 압축 해제 디스크 이미지
파일 이름: BGX50_06.exe
파일 크기: 490 KB
대용량 파일입니다. 인터넷 속도에 따라 다운로드하는 데 일정 시간이 소요될 수 있습니다.
형식 설명:
이 파일에는 압축된 파일 세트가 있습니다. 파일을 하드 드라이브의 폴더로 다운로드한 다음 두 번 클릭하여 파일 세트를 압축 해제합니다. 지침에 따라 설치를 완료합니다.
다운로드의 무결성을 보장하려면 체크섬 값을 확인하십시오.
MD5:
이용 불가
SHA1:
이용 불가
SHA-256:
이용 불가
파일 형식: 플래시 BIOS 실행 파일
파일 이름: GX50_A06.EXE
파일 크기: 316.68 KB
대용량 파일입니다. 인터넷 속도에 따라 다운로드하는 데 일정 시간이 소요될 수 있습니다.
형식 설명:
이 파일 포맷은 BIOS 실행 파일로 구성됩니다. 시스템을 업데이트하려면 파일을 다운로드하고 데스크탑 또는 하드 드라이브에 저장한 다음 실행 파일을 실행하십시오. BIOS를 업데이트하려면 시스템이 반드시 AC 전원에 연결되어 있어야 하고 배터리 충전 단계는 최소 10% 이상이어야 합니다.
다운로드의 무결성을 보장하려면 체크섬 값을 확인하십시오.
MD5:
이용 불가
SHA1:
이용 불가
SHA-256:
이용 불가
다운로드할 경우 Dell 소프트웨어 라이센스 계약 (영어로) 에 동의하는 것으로 간주합니다.
적용 대상
�
OPTIPLEX 330 SYSTEM BIOS
OptiPlex System BIOS
설치 방법
Default Instructions for GX50_A06.EXE:
Non-Packaged
Creating the disk:
NOTE: This procedure requires one blank bootable, formatted 3.5-inch
floppy disk; label the disk BIOS.
1. When the File Download window appears, click “Save this program to
disk”.
2. Choose “Desktop” as the location.
3. Click “Ok”.
4. After the file has finished copying files, click “Close”.
5. Press the “Windows” + “M” keys at the same time to minimize all
the open windows.
6. Insert the blank bootable formatted 3.5-inch floppy disk.
7. Right-click the copy of the file, point to “Send To”, click “3 1/2
Floppy (a)”, and then skip to the section Flashing the BIOS below.
Flashing the BIOS:
NOTICE: Changing the system BIOS may result in unintended side affects,
such as incompatibility of the new BIOS with installed hardware. If
problems arise after a BIOS change, it may be necessary to return the
system to the original version of the BIOS.
1. If you are flashing the BIOS on a portable computer, be sure that
the AC adapter is plugged in and the computer is not operating on battery
power.
2. Ensure that the Flash BIOS disk is inserted into the floppy disk
drive.
3. Click the “Start” button, click “Shut Down”, click “Restart”, and
then click “Ok”.
The computer should restart and boot to the floppy disk.
NOTE: If the flash BIOS program does not start, and you see only an A:\
prompt, refer to the instructions from the Dell File Library page for the
BIOS update or to the Readme.txt instructions. Generally, you will type
the name of the executable flash BIOS file such as BGX1_A10.exe for BIOS
version A10 on the OptiPlex™ series system.
A Press any key to continue prompt appears.
4. Press the “Enter” key.
A Press Y to replace old BIOS with new BIOS prompt appears.
5. Press the “Y” key.
NOTICE: Do not interrupt the system during this process. Please refrain
from pressing any keys on the keyboard, moving the mouse, or interrupting
power to the system. Failure to do so could result in damage to the system
BIOS.
When the computer has finished updating the BIOS, a Flash program
successful. Press any key to reboot prompt appears.
6. Remove the floppy disk and press the “Enter” key.
7. The computer will now restart with the new revision of the BIOS
installed.
The boot screen will indicate the BIOS version.
If you encounter device or resource errors after flashing the system BIOS,
enter the System Setup, clear the NVRAM and restore the system defaults.
For more information, refer to Dell Knowledge Base Articles:
· FA1035264 Title "How do I restore setup defaults on my Dell
OptiPlex system?"
· FA1035227 Title "How do I clear NVRAM on my Dell OptiPlex system?"
Floppy Disk Boot to Disk for BGX50_06.exe
Download
1. Click Download Now, to download the file.
2. When the File Download window appears, click Save (Windows XP users will click Save) this program to disk and click OK. The Save In:
window appears.
3. From the Save In: field, click the down arrow then click to
select Desktop and click Save. The file will download to your desktop.
4. If the Download Complete window appears, click Close. The file
icon appears on your desktop.
Hard Drive Floppy Disk Creation
1. Get 1 blank, formatted floppy disks.
2. Double-click the new icon (it looks like a floppy diskette) on
the desktop. The Self-Extractor window appears.
3. Click Setup. An black MS-DOS window appears with a message
indicating that you need 1 floppy diskettes.
4. Press the [ENTER] key.
A message appears prompting you to insert a blank floppy diskette.
5. Insert a floppy disk into the floppy disk drive.
6. Press the [ENTER] key. A message appears indicating that all
data on the disk will be erased.
7. Press the [y] key and then press the [ENTER] key.
The files are copied to
Default Instructions for GX50_A06.EXE:
Non-Packaged
Creating the disk:
NOTE: This procedure requires one blank bootable, formatted 3.5-inch
floppy disk; label the disk BIOS.
1. When the File Download window appears, click “Save this program to
disk”.
2. Choose “Desktop” as the location.
3. Click “Ok”.
4. After the file has finished copying files, click “Close”.
5. Press the “Windows” + “M” keys at the same time to minimize all
the open windows.
6. Insert the blank bootable formatted 3.5-inch floppy disk.
7. Right-click the copy of the file, point to “Send To”, click “3 1/2
Floppy (a)”, and then skip to the section Flashing the BIOS below.
Flashing the BIOS:
NOTICE: Changing the system BIOS may result in unintended side affects,
such as incompatibility of the new BIOS with installed hardware. If
problems arise after a BIOS change, it may be necessary to return the
system to the original version of the BIOS.
1. If you are flashing the BIOS on a portable computer, be sure that
the AC adapter is plugged in and the computer is not operating on battery
power.
2. Ensure that the Flash BIOS disk is inserted into the floppy disk
drive.
3. Click the “Start” button, click “Shut Down”, click “Restart”, and
then click “Ok”.
The computer should restart and boot to the floppy disk.
NOTE: If the flash BIOS program does not start, and you see only an A:\
prompt, refer to the instructions from the Dell File Library page for the
BIOS update or to the Readme.txt instructions. Generally, you will type
the name of the executable flash BIOS file such as BGX1_A10.exe for BIOS
version A10 on the OptiPlex™ series system.
A Press any key to continue prompt appears.
4. Press the “Enter” key.
A Press Y to replace old BIOS with new BIOS prompt appears.
5. Press the “Y” key.
NOTICE: Do not interrupt the system during this process. Please refrain
from pressing any keys on the keyboard, moving the mouse, or interrupting
power to the system. Failure to do so could result in damage to the system
BIOS.
When the computer has finished updating the BIOS, a Flash program
successful. Press any key to reboot prompt appears.
6. Remove the floppy disk and press the “Enter” key.
7. The computer will now restart with the new revision of the BIOS
installed.
The boot screen will indicate the BIOS version.
If you encounter device or resource errors after flashing the system BIOS,
enter the System Setup, clear the NVRAM and restore the system defaults.
For more information, refer to Dell Knowledge Base Articles:
· FA1035264 Title "How do I restore setup defaults on my Dell
OptiPlex system?"
· FA1035227 Title "How do I clear NVRAM on my Dell OptiPlex system?"
Floppy Disk Boot to Disk for BGX50_06.exe
Download
1. Click Download Now, to download the file.
2. When the File Download window appears, click Save (Windows XP users will click Save) this program to disk and click OK. The Save In:
window appears.
3. From the Save In: field, click the down arrow then click to
select Desktop and click Save. The file will download to your desktop.
4. If the Download Complete window appears, click Close. The file
icon appears on your desktop.
Hard Drive Floppy Disk Creation
1. Get 1 blank, formatted floppy disks.
2. Double-click the new icon (it looks like a floppy diskette) on
the desktop. The Self-Extractor window appears.
3. Click Setup. An black MS-DOS window appears with a message
indicating that you need 1 floppy diskettes.
4. Press the [ENTER] key.
A message appears prompting you to insert a blank floppy diskette.
5. Insert a floppy disk into the floppy disk drive.
6. Press the [ENTER] key. A message appears indicating that all
data on the disk will be erased.
7. Press the [y] key and then press the [ENTER] key.
The files are copied to