American Megatrends (AMI) PERC 2/SC, PERC2/DC, v.4.21, A03
자동 설치 완료 이 파일은 최근 업데이트의 일부로 자동으로 설치되었습니다. 문제가 발생하는 경우 수동으로 다운로드하고 재설치할 수 있습니다.이 페이지의 콘텐츠는 자동으로 번역되었을 수 있습니다. 피드백을 제공하려면 페이지 하단에 있는 양식을 작성하십시오.
Dell PowerEdge RAID Controller 2/SC, 2/DC, 4/DC, 4/SC, 3/QC, 3/DC, 3/DCL, 3/SC, PERC 4/Di, and CERC ATA100/4CH, Device Driver for Windows NT 4.0.
Version: 4.21
Version: 4.21
권장 사항
자동 스캔을 사용하려면 관리자 권한으로 Windows에 로그인하십시오. 관리자 권한으로 이미 로그인한 상태에서 이 메시지가 표시되었다면 재부팅하시기 바랍니다. 시스템이 IT 관리자에 의해 관리되고 있으며, 기능이 제한될 수 있습니다.
추가 업데이트 사항을 찾습니다. SupportAssist를 사용하여 디바이스에 대한 모든 최신 드라이버 업데이트를 찾습니다.
수정 또는 개선한 내용
Fixes or Enhancements in this Release
Enhancements:
1) None.
Fixes:
1) A fix was made in the Driver to initialize the data Structures for some of the IOCTL calls.
2) Driver no longer filters out all other commands except SCSI READ and SCSI WRITE
자세히 보기Enhancements:
1) None.
Fixes:
1) A fix was made in the Driver to initialize the data Structures for some of the IOCTL calls.
2) Driver no longer filters out all other commands except SCSI READ and SCSI WRITE
버전
4.21, A03
출시일
27 10월 2004
다운로드 유형
드라이버
범주
SCSI RAID
중요도
옵션Dell Technologies는 이 업데이트를 검토하여 시스템에 대한 적용 여부를 판단할 것을 고객에게 권장합니다. 이 업데이트에는 특정 구성에 대해서만 영향을 미치는 변경 사항이 포함되어 있거나 해당 시스템 환경에 적용될 수도 있는 새 기능이 포함되어 있습니다.
사용 가능한 형식
파일 형식: MS Windows 32비트용 업데이트 패키지
파일 이름: RAID-DRVR-R65397.exe
파일 크기: 967.68 KB
대용량 파일입니다. 인터넷 속도에 따라 다운로드하는 데 일정 시간이 소요될 수 있습니다.
형식 설명:
Microsoft Windows 32비트 형식의 DUP(Dell 업데이트 패키지)는 Microsoft Windows 64비트 운영 체제를 실행하도록 설계되었습니다. Microsoft Windows 64비트 형식의 DUP(Dell 업데이트 패키지)는 Microsoft Windows 64비트 운영 체제에서만 실행됩니다. 장치 드라이버 업데이트를 선택할 때 운영 체제에 적합한 업데이트를 선택하도록 하십시오.
다운로드의 무결성을 보장하려면 체크섬 값을 확인하십시오.
MD5:
0BEA91746EF294C939BAF93BDDF93608
SHA1:
이용 불가
SHA-256:
이용 불가
파일 형식: 로컬 디스크로 직접 파일 압축 해제
파일 이름: PERC2-NT421-A03.exe
파일 크기: 84 KB
대용량 파일입니다. 인터넷 속도에 따라 다운로드하는 데 일정 시간이 소요될 수 있습니다.
형식 설명:
이 파일 포맷은 하드 드라이브의 디렉토리로 압축 해제할 수 있는 파일의 아카이브로 구성됩니다. 설치는 그 이후 해당 디렉토리에서 수행할 수 있습니다.
다운로드의 무결성을 보장하려면 체크섬 값을 확인하십시오.
MD5:
이용 불가
SHA1:
이용 불가
SHA-256:
이용 불가
다운로드할 경우 Dell 소프트웨어 라이센스 계약 (영어로) 에 동의하는 것으로 간주합니다.
지원되는 운영 체제
Windows NT 4.0
설치 방법
Custom Instructions for PERC2-NT421-A03.exe:
Dell PowerEdge RAID Controller 2/Sc, 2/DC, 4/DC, 4/SC, 3/QC, 3/DC, 3/DCL, 3/SC, 4/Di, and CERC ATA100/4CH, Device Driver for Windows NT 4.0
Version 4.21
Install Instructions
Download
1. Click the "Download Now" link to download the file.
2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement.
3. When the File Download window appears, click "Save" to save the file to your hard drive.
Extract Files
1. Browse to the location where you downloaded the file and double-click the new file to unzip the download package.
2. Specify the location to unzip the files – the instructions below assume you extract files to a formatted floppy disk.
3. Click on the unzip button to extract files.
Installation
Dell PowerEdge RAID Controller 4/DC, 4/SC, 3/QC, 3/DC, 3/DCL, 3/SC, 4/Di, and CERC ATA100/4CH, Device Driver for Windows NT 4.0
Version 4.21
This program creates a Windows NT 4.0 driver diskette for the controllers. You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
1) Download the file to a directory on your hard drive. The file downloaded is a self-extracting executable.
2) Double click on the file to run the executable.
3) Click on the unzip button to extract files to the floppy.
Power down the system and install the PERC/CERC card. Configure the logical drives before proceeding with the driver install described below.
Performing a New Installation of Windows NT 4.0
"Making PERC/CERC the Primary Controller in Windows NT 4.0"
1) Boot the system using the Windows NT 4.0 CD. As the message "Setup is inspecting your computer's hardware configuration." appears. Press F6 immediately.
2) Within a few seconds, the Windows NT Setup screen appears, requesting additional adapters in the system. Press 'S' to specify an additional device, then press Enter on the OTHER option in the selection screen.
3) Insert the PERC/CERC driver diskette created above and press Enter. "CERC ATA100/4ch; PERC2/3/4 Series Windows NT Driver" appears. Press Enter to load the driver.
4) Press 'S' to load additional mass storage device driver if required. Otherwise, press Enter to continue installation process as usual. Windows NT 4.0 continues to be installed as usual. Please refer to the operating system installation documentation for further steps.
"Making PERC/CERC a Secondary Controller in Windows NT 4.0"
1) Start the Windows NT 4.0 installation process. Load the device for the primary controller if necessary.
2) Windows NT Server Setup screen is displayed after loading Windows NT Kernel. Press Enter to continue.
3) Setup displays mass storage devices that it has recognized in your computer. Press 'S' to specify an additional device, then press Enter on the OTHER option in the selection screen.
4) Insert the PERC/CERC driver diskette created above and press Enter. "CERC ATA100/4ch; PERC2/3/4 Series Windows NT Driver" appears. Press Enter to load the driver.
5) Press 'S' to load additional mass storage device drivers if required; otherwise, press Enter to continue the installation process as usual. Windows NT 4.0 continues to be installed as usual. Please refer to the operating system installation documentation for further steps.
Adding the PERC/CERC Driver to an Existing Windows NT 4.0 Server
If your server is already running Windows NT 4.0, then use the following steps to add the PERC/CERC Windows NT 4.0 driver.
1) Insert the PERC/CERC driver diskette created above in appropriate drive. The driver files can also be installed from a local or network drive.
2) Click on Start > Control Panel > Settings. Double-click on the Small Computer System Interface (SCSI) Adapter icon.
3) Select the Drivers tab.
4) Click on the Add button.
5) Select Have Disk.
6) The Install From Disk box appears. Specify the l
Custom Instructions for PERC2-NT421-A03.exe:
Dell PowerEdge RAID Controller 2/Sc, 2/DC, 4/DC, 4/SC, 3/QC, 3/DC, 3/DCL, 3/SC, 4/Di, and CERC ATA100/4CH, Device Driver for Windows NT 4.0
Version 4.21
Install Instructions
Download
1. Click the "Download Now" link to download the file.
2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement.
3. When the File Download window appears, click "Save" to save the file to your hard drive.
Extract Files
1. Browse to the location where you downloaded the file and double-click the new file to unzip the download package.
2. Specify the location to unzip the files – the instructions below assume you extract files to a formatted floppy disk.
3. Click on the unzip button to extract files.
Installation
Dell PowerEdge RAID Controller 4/DC, 4/SC, 3/QC, 3/DC, 3/DCL, 3/SC, 4/Di, and CERC ATA100/4CH, Device Driver for Windows NT 4.0
Version 4.21
This program creates a Windows NT 4.0 driver diskette for the controllers. You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
1) Download the file to a directory on your hard drive. The file downloaded is a self-extracting executable.
2) Double click on the file to run the executable.
3) Click on the unzip button to extract files to the floppy.
Power down the system and install the PERC/CERC card. Configure the logical drives before proceeding with the driver install described below.
Performing a New Installation of Windows NT 4.0
"Making PERC/CERC the Primary Controller in Windows NT 4.0"
1) Boot the system using the Windows NT 4.0 CD. As the message "Setup is inspecting your computer's hardware configuration." appears. Press F6 immediately.
2) Within a few seconds, the Windows NT Setup screen appears, requesting additional adapters in the system. Press 'S' to specify an additional device, then press Enter on the OTHER option in the selection screen.
3) Insert the PERC/CERC driver diskette created above and press Enter. "CERC ATA100/4ch; PERC2/3/4 Series Windows NT Driver" appears. Press Enter to load the driver.
4) Press 'S' to load additional mass storage device driver if required. Otherwise, press Enter to continue installation process as usual. Windows NT 4.0 continues to be installed as usual. Please refer to the operating system installation documentation for further steps.
"Making PERC/CERC a Secondary Controller in Windows NT 4.0"
1) Start the Windows NT 4.0 installation process. Load the device for the primary controller if necessary.
2) Windows NT Server Setup screen is displayed after loading Windows NT Kernel. Press Enter to continue.
3) Setup displays mass storage devices that it has recognized in your computer. Press 'S' to specify an additional device, then press Enter on the OTHER option in the selection screen.
4) Insert the PERC/CERC driver diskette created above and press Enter. "CERC ATA100/4ch; PERC2/3/4 Series Windows NT Driver" appears. Press Enter to load the driver.
5) Press 'S' to load additional mass storage device drivers if required; otherwise, press Enter to continue the installation process as usual. Windows NT 4.0 continues to be installed as usual. Please refer to the operating system installation documentation for further steps.
Adding the PERC/CERC Driver to an Existing Windows NT 4.0 Server
If your server is already running Windows NT 4.0, then use the following steps to add the PERC/CERC Windows NT 4.0 driver.
1) Insert the PERC/CERC driver diskette created above in appropriate drive. The driver files can also be installed from a local or network drive.
2) Click on Start > Control Panel > Settings. Double-click on the Small Computer System Interface (SCSI) Adapter icon.
3) Select the Drivers tab.
4) Click on the Add button.
5) Select Have Disk.
6) The Install From Disk box appears. Specify the l