Maxtor Aurora 15K U320 18GB 68 Pin, Aurora 15K U320 18GB 80 Pin, Aurora 15K U320 36GB 68 Pin, Aurora 15K U320 36GB 80 Pin, Aurora 15K U320 73GB 68 Pin, Aurora 15K U320 73GB 80 Pin, v.1.0, A00
자동 설치 완료 이 파일은 최근 업데이트의 일부로 자동으로 설치되었습니다. 문제가 발생하는 경우 수동으로 다운로드하고 재설치할 수 있습니다.이 페이지의 콘텐츠는 자동으로 번역되었을 수 있습니다. 피드백을 제공하려면 페이지 하단에 있는 양식을 작성하십시오.
This utility disables the read-lookahead (ESP) feature of the drive.
권장 사항
자동 스캔을 사용하려면 관리자 권한으로 Windows에 로그인하십시오. 관리자 권한으로 이미 로그인한 상태에서 이 메시지가 표시되었다면 재부팅하시기 바랍니다. 시스템이 IT 관리자에 의해 관리되고 있으며, 기능이 제한될 수 있습니다.
추가 업데이트 사항을 찾습니다. SupportAssist를 사용하여 디바이스에 대한 모든 최신 드라이버 업데이트를 찾습니다.
수정 또는 개선한 내용
Initial Release
A timeout problem was reported with Maxtor Atlas 15K SCSI hard disk drives running a specific Hard Drive Stress test script under Linux 9.0 within a PE1600SC system. When the Messages log file within Linux is viewed, a System Timeout, Bus Reset, and 04/40/0C check condition may be recorded.
This issue was found while running the Hard Drive stress test. There is no known customer reported problem running a specific application. In this test environment, the drive is requested to perform reverse sequential reads. In some cases, this issue can intermittently create an internal race condition causing the the drive to ‘hang’, requiring the Operating system to issue a bus reset.
자세히 보기A timeout problem was reported with Maxtor Atlas 15K SCSI hard disk drives running a specific Hard Drive Stress test script under Linux 9.0 within a PE1600SC system. When the Messages log file within Linux is viewed, a System Timeout, Bus Reset, and 04/40/0C check condition may be recorded.
This issue was found while running the Hard Drive stress test. There is no known customer reported problem running a specific application. In this test environment, the drive is requested to perform reverse sequential reads. In some cases, this issue can intermittently create an internal race condition causing the the drive to ‘hang’, requiring the Operating system to issue a bus reset.
버전
1.0, A00
출시일
31 10월 2003
다운로드 유형
유틸리티
범주
SCSI 드라이브
중요도
옵션Dell Technologies는 이 업데이트를 검토하여 시스템에 대한 적용 여부를 판단할 것을 고객에게 권장합니다. 이 업데이트에는 특정 구성에 대해서만 영향을 미치는 변경 사항이 포함되어 있거나 해당 시스템 환경에 적용될 수도 있는 새 기능이 포함되어 있습니다.
사용 가능한 형식
파일 형식: 자동 압축 해제 zip 내부의 하나 이상의 자동 압축 해제 디스크 이미지
파일 이름: BR67588.exe
파일 크기: 881.34 KB
대용량 파일입니다. 인터넷 속도에 따라 다운로드하는 데 일정 시간이 소요될 수 있습니다.
형식 설명:
이 파일에는 압축된 파일 세트가 있습니다. 파일을 하드 드라이브의 폴더로 다운로드한 다음 두 번 클릭하여 파일 세트를 압축 해제합니다. 지침에 따라 설치를 완료합니다.
다운로드의 무결성을 보장하려면 체크섬 값을 확인하십시오.
MD5:
이용 불가
SHA1:
이용 불가
SHA-256:
이용 불가
다운로드할 경우 Dell 소프트웨어 라이센스 계약 (영어로) 에 동의하는 것으로 간주합니다.
지원되는 운영 체제
Red Hat® Enterprise Linux 2.1
Red Hat® Linux 8.0
Red Hat® Linux 9.0
Windows Server 2003
Windows 2000
적용 대상
Aurora 15K U320 18GB 68 Pin
Aurora 15K U320 18GB 80 Pin
Aurora 15K U320 36GB 68 Pin
Aurora 15K U320 36GB 80 Pin
Aurora 15K U320 73GB 68 Pin
Aurora 15K U320 73GB 80 Pin
설치 방법
Custom Instructions for BR67588.exe:
Utility must be placed on a non-write protected diskette.
NOTE: In order to create this diskette, the file must be downloaded to and executed on a system running Microsoft Windows.
Download
1. Click the "Download Now" link to download the file.
2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement.
3. When the File Download window appears, click "Save" to save the file to your hard drive.
Diskette Creation
1. Browse to the location where you downloaded the file and double-click the new file to create the diskette set.
2. Insert a blank diskette then click Continue.
3. After all the files have been copied to the last, click Finish.
Installation:
NOTE: BACKUP ALL DATA BEFORE RUNNING THIS PROGRAM. Do not remove power from the devices or disturb the devices in any way while the download is in progress. Dell, Inc is not Responsible for any data loss resulting from the use of this program
NOTE: Before proceeding with the update, refer to README.TXT file, section 4.0 "Using The Update Utility" for important information regarding the update process.
For drives connected to an LSI 1020 or 1030 SCSI controller:
1. Insert the firmware update diskette into the floppy drive and reboot the system.
2. The utility will automatically determine the correct device to update when booted
3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to an Adapted 7899 or 39160 SCSI controller:
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line Device=ASPIDRV\ASPI8U2.SYS and adding the ‘REM’ statement to the line Device=ASPIDRV\ASPIMPT.SYS. This modification loads the ASPI driver for Adaptec controllers instead of the ASPI driver for LSI controllers
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 0 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC):
1. Insert the firmware update diskette into the floppy drive and reboot the system.
2. The utility will automatically determine the correct device to update when booted
3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 1 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC):
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line “Device=ASPIDRV\MEGASPI.SYS /a1” and adding the REM statement to the line “Device=ASPIDRV\MEGASPI.SYS /a0”.
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.
For drives connected an Adaptec RAID controller (PERC 3/Si, PERC 3/DI):
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line "Device=ASPIDRV\ELITEAPI.SYS /M" and adding the ‘REM’ statement to the lines “Device=ASPIDRV\MEGASPI.SYS /a0” and “Device=ASPIDRV\MEGASPI.SYS /a1”.
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.
Utility must be placed on a non-write protected diskette.
NOTE: In order to create this diskette, the file must be downloaded to and executed on a system running Microsoft Windows.
Download
1. Click the "Download Now" link to download the file.
2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement.
3. When the File Download window appears, click "Save" to save the file to your hard drive.
Diskette Creation
1. Browse to the location where you downloaded the file and double-click the new file to create the diskette set.
2. Insert a blank diskette then click Continue.
3. After all the files have been copied to the last, click Finish.
Installation:
NOTE: BACKUP ALL DATA BEFORE RUNNING THIS PROGRAM. Do not remove power from the devices or disturb the devices in any way while the download is in progress. Dell, Inc is not Responsible for any data loss resulting from the use of this program
NOTE: Before proceeding with the update, refer to README.TXT file, section 4.0 "Using The Update Utility" for important information regarding the update process.
For drives connected to an LSI 1020 or 1030 SCSI controller:
1. Insert the firmware update diskette into the floppy drive and reboot the system.
2. The utility will automatically determine the correct device to update when booted
3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to an Adapted 7899 or 39160 SCSI controller:
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line Device=ASPIDRV\ASPI8U2.SYS and adding the ‘REM’ statement to the line Device=ASPIDRV\ASPIMPT.SYS. This modification loads the ASPI driver for Adaptec controllers instead of the ASPI driver for LSI controllers
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 0 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC):
1. Insert the firmware update diskette into the floppy drive and reboot the system.
2. The utility will automatically determine the correct device to update when booted
3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 1 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC):
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line “Device=ASPIDRV\MEGASPI.SYS /a1” and adding the REM statement to the line “Device=ASPIDRV\MEGASPI.SYS /a0”.
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.
For drives connected an Adaptec RAID controller (PERC 3/Si, PERC 3/DI):
1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line "Device=ASPIDRV\ELITEAPI.SYS /M" and adding the ‘REM’ statement to the lines “Device=ASPIDRV\MEGASPI.SYS /a0” and “Device=ASPIDRV\MEGASPI.SYS /a1”.
2. Insert the firmware update diskette into the floppy drive and reboot the system.
3. The utility will automatically determine the correct device to update when booted
4. Once the update is complete Remove the diskette and reboot the system.