AUTO-INSTALLATIONCe fichier a été automatiquement installé dans le cadre d’une mise à jour récente. Si vous rencontrez des problèmes, vous pouvez le télécharger et le réinstaller manuellement.
Le contenu de cette page a peut-être été traduit automatiquement. Pour faire part de vos commentaires, remplissez le formulaire au bas de la page.
Ce fichier a été automatiquement installé dans le cadre d’une mise à jour récente. Si vous rencontrez des problèmes, vous pouvez le télécharger et le réinstaller manuellement.
PERC 4/Di Device Driver for Red Hat Linux 7.2.
Recommandé
Trouver le meilleur téléchargement pour votre système
Saisissez les détails de votre produit pour afficher les dernières informations sur le pilote de votre système.
Rechercher dans le support
Saisir votre modèle ou numéro de série Dell
Vous souhaitez rechercher votre produit ? Saisissez un identifiant de produit.Comment faire
Ce pilote ne s’applique pas au produit sélectionné. Choisissez un autre produit pour saisir de nouveau les détails de votre produit pour ce pilote ou rendez-vous sur la page du support produit pour afficher tous les pilotes d’un autre produit.
Connectez-vous à Windows en tant qu’administrateur pour utiliser les fonctionnalités d’analyse automatique. Si vous êtes déjà connecté en tant qu’administrateur et que vous voyez ce message, redémarrez.Votre système est géré par votre administrateur IT et peut avoir des fonctionnalités limitées.
Trouver d’autres mises à jour. Utilisez SupportAssist pour trouver toutes les dernières mises à jour de pilotes disponibles pour votre appareil.
Dell Technologies recommande de consulter cette mise à jour pour déterminer si elle s’applique à votre système. La mise à jour comprend des modifications n’ayant d’impact que sur certaines configurations, ou propose de nouvelles fonctionnalités pouvant s’appliquer ou non à votre environnement.
Format de fichier :Extrait des fichiers directement vers le disque local
Nom du fichier :perc4di-118c-72c.tar.gz
Taille du fichier :538.62 KB
Ce fichier est volumineux. En fonction de la vitesse de votre connexion, le téléchargement peut prendre un certain temps.
Description du format:
Ce format de fichier comprend une archive de fichiers qui peut être décompressée sur un répertoire du disque dur. L’installation peut être effectuée à partir de ce répertoire.
Instructions for downloading and creating driver diskette: ----------------------------------------------------------
You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
Download the file PERC4di-118c-72c.tar.gz to a temporary directory on your working system.
Extract the file to the floppy disk as follows:
1. On a Linux system:
Type the following commands under a Linux command shell: mount /dev/fd0 /mnt/floppy tar xvzf -C /mnt/floppy (Eg: /temp/PERC4di-118c-72c.tar.gz) umount /mnt/floppy
2. On a Microsoft Windows system:
You can use Winzip to extract tar.gz archives. However, note the following settings under Winzip to ensure correct extraction of the files.
Start Winzip -> Go to Options -> Configuration
Under the Miscellaneous tab make sure "TAR file smart CR/LF conversion" is unchecked.
Upon opening the tar.gz archive with Winzip, you get the following prompt:
'Archive contains one file. Should Winzip decompress it to a temporary folder and open it?'
Press 'yes' and extract the files normally under Winzip to the floppy drive.
Install Red Hat Linux 7.2 driver for PERC 4/Di as a boot controller -------------------------------------------------------
There are two ways of installing Red Hat 7.2 driver onto the PERC 4/Di as a boot controller. One is using a driver disk during OS installation and the second is using a driver (megaraid) RPM to update driver after OS is installed. The steps for both of these methods are provided below. All the files needed for both methods are included in the driver diskette created above.
For more detailed installation instructions of Red Hat 7.2, please refer to the OS installation guide at http://www.dell.com/linux.
I. Installing driver during OS installation: --------------------------------------------
1. Boot normally from the Redhat installation CD-Rom.
2. Type 'linux dd' on the boot prompt.
3. When the install prompts for a driver disk, insert the driver diskette created above and press 'Enter'.
4. Installation progresses normally. Continue until the 'Create Bootdisk' screen. Press CTRL-ALT-F2 to get to a shell window and type the following commands:
chroot /mnt/sysimage cd /boot /sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10 lilo ( only if lilo was used as bootloader. If grub used - skip this step ) exit
Press CTRL-ALT-F7 to get back to the install screen.
5. Complete the installation as directed by the install.
II. Update driver using RPMs after OS is installed --------------------------------------------------
Type the following commands under a Linux command shell:
mount /dev/fd0 /mnt/floppy cd /mnt/floppy ./megarpmwrapper.sh
Than follow the on-screen instructions to install the RPM driver.
For more detailed information about the script megarpmwrapper.sh, please refer to the release_notes.txt included in the release.