AUTO-INSTALLATIONCe fichier a été automatiquement installé dans le cadre d’une mise à jour récente. Si vous rencontrez des problèmes, vous pouvez le télécharger et le réinstaller manuellement.
Le contenu de cette page a peut-être été traduit automatiquement. Pour faire part de vos commentaires, remplissez le formulaire au bas de la page.
Ce fichier a été automatiquement installé dans le cadre d’une mise à jour récente. Si vous rencontrez des problèmes, vous pouvez le télécharger et le réinstaller manuellement.
This utility disables the read-lookahead (ESP) feature of the drive.
Recommandé
Trouver le meilleur téléchargement pour votre système
Saisissez les détails de votre produit pour afficher les dernières informations sur le pilote de votre système.
Rechercher dans le support
Saisir votre modèle ou numéro de série Dell
Vous souhaitez rechercher votre produit ? Saisissez un identifiant de produit.Comment faire
Ce pilote ne s’applique pas au produit sélectionné. Choisissez un autre produit pour saisir de nouveau les détails de votre produit pour ce pilote ou rendez-vous sur la page du support produit pour afficher tous les pilotes d’un autre produit.
Connectez-vous à Windows en tant qu’administrateur pour utiliser les fonctionnalités d’analyse automatique. Si vous êtes déjà connecté en tant qu’administrateur et que vous voyez ce message, redémarrez.Votre système est géré par votre administrateur IT et peut avoir des fonctionnalités limitées.
Trouver d’autres mises à jour. Utilisez SupportAssist pour trouver toutes les dernières mises à jour de pilotes disponibles pour votre appareil.
Correctifs et améliorations
Initial Release A timeout problem was reported with Maxtor Atlas 15K SCSI hard disk drives running a specific Hard Drive Stress test script under Linux 9.0 within a PE1600SC system. When the Messages log file within Linux is viewed, a System Timeout, Bus Reset, and 04/40/0C check condition may be recorded.
This issue was found while running the Hard Drive stress test. There is no known customer reported problem running a specific application. In this test environment, the drive is requested to perform reverse sequential reads. In some cases, this issue can intermittently create an internal race condition causing the the drive to ‘hang’, requiring the Operating system to issue a bus reset.
Dell Technologies recommande de consulter cette mise à jour pour déterminer si elle s’applique à votre système. La mise à jour comprend des modifications n’ayant d’impact que sur certaines configurations, ou propose de nouvelles fonctionnalités pouvant s’appliquer ou non à votre environnement.
Format de fichier :Une ou plusieurs images de disque dans un zip (tous à extraction automatique)
Nom du fichier :BR67588.exe
Taille du fichier :881.34 KB
Ce fichier est volumineux. En fonction de la vitesse de votre connexion, le téléchargement peut prendre un certain temps.
Description du format:
Ce fichier contient un ensemble de fichiers compressés (ou zippés). Téléchargez le fichier vers un dossier de votre disque dur et double-cliquez dessus pour décompresser les fichiers. Suivez les instructions pour terminer l’installation.
Utility must be placed on a non-write protected diskette.
NOTE: In order to create this diskette, the file must be downloaded to and executed on a system running Microsoft Windows.
Download 1. Click the "Download Now" link to download the file. 2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement. 3. When the File Download window appears, click "Save" to save the file to your hard drive.
Diskette Creation 1. Browse to the location where you downloaded the file and double-click the new file to create the diskette set. 2. Insert a blank diskette then click Continue. 3. After all the files have been copied to the last, click Finish.
Installation: NOTE: BACKUP ALL DATA BEFORE RUNNING THIS PROGRAM. Do not remove power from the devices or disturb the devices in any way while the download is in progress. Dell, Inc is not Responsible for any data loss resulting from the use of this program
NOTE: Before proceeding with the update, refer to README.TXT file, section 4.0 "Using The Update Utility" for important information regarding the update process.
For drives connected to an LSI 1020 or 1030 SCSI controller: 1. Insert the firmware update diskette into the floppy drive and reboot the system. 2. The utility will automatically determine the correct device to update when booted 3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to an Adapted 7899 or 39160 SCSI controller: 1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line Device=ASPIDRV\ASPI8U2.SYS and adding the ‘REM’ statement to the line Device=ASPIDRV\ASPIMPT.SYS. This modification loads the ASPI driver for Adaptec controllers instead of the ASPI driver for LSI controllers 2. Insert the firmware update diskette into the floppy drive and reboot the system. 3. The utility will automatically determine the correct device to update when booted 4. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 0 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC): 1. Insert the firmware update diskette into the floppy drive and reboot the system. 2. The utility will automatically determine the correct device to update when booted 3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 1 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC): 1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line “Device=ASPIDRV\MEGASPI.SYS /a1” and adding the REM statement to the line “Device=ASPIDRV\MEGASPI.SYS /a0”. 2. Insert the firmware update diskette into the floppy drive and reboot the system. 3. The utility will automatically determine the correct device to update when booted 4. Once the update is complete Remove the diskette and reboot the system.
For drives connected an Adaptec RAID controller (PERC 3/Si, PERC 3/DI): 1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line "Device=ASPIDRV\ELITEAPI.SYS /M" and adding the ‘REM’ statement to the lines “Device=ASPIDRV\MEGASPI.SYS /a0” and “Device=ASPIDRV\MEGASPI.SYS /a1”. 2. Insert the firmware update diskette into the floppy drive and reboot the system. 3. The utility will automatically determine the correct device to update when booted 4. Once the update is complete Remove the diskette and reboot the system.