AUTOMATISCH GEÏNSTALLEERDDit bestand is automatisch geïnstalleerd als onderdeel van een recente update. Als u problemen ondervindt, kunt u deze handmatig downloaden en opnieuw installeren.
De inhoud van deze pagina is mogelijk automatisch vertaald. Vul het formulier onderaan de pagina in om feedback te geven.
Dit bestand is automatisch geïnstalleerd als onderdeel van een recente update. Als u problemen ondervindt, kunt u deze handmatig downloaden en opnieuw installeren.
PERC 4/Di Device Driver for Red Hat Linux 7.2.
Aanbevolen
Vind de beste download voor uw systeem
Voer uw productgegevens in om de meest recente driverinformatie voor uw systeem weer te geven.
Support zoeken
Voer uw Dell servicetag of model in
Wilt u uw product opzoeken? Voer een product-ID in.Meer informatie
Geen resultaten gevonden. We hebben geen resultaten gevonden voor uw zoekopdracht. Wijzig uw zoekopdracht en probeer het opnieuw.
Deze driver is niet compatibel
Deze driver is niet van toepassing op het geselecteerde product. Kies een ander product om uw productinformatie voor deze driver opnieuw in te voeren of ga naar de productsupportpagina om alle drivers voor een ander product weer te geven.
Meld u aan bij Windows als beheerder om automatische scanfuncties te gebruiken. Als u al bent aangemeld als beheerder en dit bericht ziet, start dan opnieuw op.Uw systeem wordt beheerd door uw IT-beheerder en de functies kunnen beperkt zijn.
Zoek meer updates. Gebruik SupportAssist om alle nieuwste driverupdates voor uw apparaat te vinden.
Dell Technologies raadt aan om deze update te bekijken om te bepalen of deze van toepassing is op uw systeem. De update bevat wijzigingen die alleen invloed hebben op sommige configuraties, of bevat nieuwe functies die al dan niet op uw omgeving van toepassing zijn.
Bestandsindeling:Extraheert bestanden rechtstreeks naar de lokale harde schijf
Bestandsnaam:perc4di-118c-72c.tar.gz
Bestandsgrootte:538.62 KB
Dit is een groot bestand. Afhankelijk van uw verbindingssnelheid kan het downloaden enige tijd duren.
Format-omschrijving:
Deze bestandsindeling bestaat uit een archief van bestanden die kunnen worden gedecomprimeerd in een map op de harde schijf. De installatie kan dan worden gedaan vanuit deze map.
Instructions for downloading and creating driver diskette: ----------------------------------------------------------
You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
Download the file PERC4di-118c-72c.tar.gz to a temporary directory on your working system.
Extract the file to the floppy disk as follows:
1. On a Linux system:
Type the following commands under a Linux command shell: mount /dev/fd0 /mnt/floppy tar xvzf -C /mnt/floppy (Eg: /temp/PERC4di-118c-72c.tar.gz) umount /mnt/floppy
2. On a Microsoft Windows system:
You can use Winzip to extract tar.gz archives. However, note the following settings under Winzip to ensure correct extraction of the files.
Start Winzip -> Go to Options -> Configuration
Under the Miscellaneous tab make sure "TAR file smart CR/LF conversion" is unchecked.
Upon opening the tar.gz archive with Winzip, you get the following prompt:
'Archive contains one file. Should Winzip decompress it to a temporary folder and open it?'
Press 'yes' and extract the files normally under Winzip to the floppy drive.
Install Red Hat Linux 7.2 driver for PERC 4/Di as a boot controller -------------------------------------------------------
There are two ways of installing Red Hat 7.2 driver onto the PERC 4/Di as a boot controller. One is using a driver disk during OS installation and the second is using a driver (megaraid) RPM to update driver after OS is installed. The steps for both of these methods are provided below. All the files needed for both methods are included in the driver diskette created above.
For more detailed installation instructions of Red Hat 7.2, please refer to the OS installation guide at http://www.dell.com/linux.
I. Installing driver during OS installation: --------------------------------------------
1. Boot normally from the Redhat installation CD-Rom.
2. Type 'linux dd' on the boot prompt.
3. When the install prompts for a driver disk, insert the driver diskette created above and press 'Enter'.
4. Installation progresses normally. Continue until the 'Create Bootdisk' screen. Press CTRL-ALT-F2 to get to a shell window and type the following commands:
chroot /mnt/sysimage cd /boot /sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10 lilo ( only if lilo was used as bootloader. If grub used - skip this step ) exit
Press CTRL-ALT-F7 to get back to the install screen.
5. Complete the installation as directed by the install.
II. Update driver using RPMs after OS is installed --------------------------------------------------
Type the following commands under a Linux command shell:
mount /dev/fd0 /mnt/floppy cd /mnt/floppy ./megarpmwrapper.sh
Than follow the on-screen instructions to install the RPM driver.
For more detailed information about the script megarpmwrapper.sh, please refer to the release_notes.txt included in the release.