Omstart krevesAUTOMATISK INSTALLERTDenne filen ble automatisk installert som en del av en nylig oppdatering. Hvis du opplever problemer, kan du laste ned og installere på nytt manuelt.
Innholdet på denne siden kan ha blitt oversatt automatisk. Fyll ut skjemaet nederst på siden for å gi tilbakemelding.
Denne filen ble automatisk installert som en del av en nylig oppdatering. Hvis du opplever problemer, kan du laste ned og installere på nytt manuelt.
This package provides the Micron RealSSD C400 128GB/256GB/512GB 2.5" 7MM Firmware Update and is supported on Alienware, Inspiron, Latitude, XPS Notebook, OptiPlex, Precision and Vostro Notebook models that are running the following Windows Operating Systems: Windows 7 and Windows 8.
Anbefalt
Finn den beste nedlastingen for systemet
Angi produktdetaljer for å vise den nyeste driverinformasjonen for systemet
Støtte for søk
Skriv inn Dell-service-ID-en eller -modellen
Ønsker du å finne produktet? Skriv inn en produktidentifikator.Vis meg hvordan
Finner ingen resultater. Vi finner ikke noe for søket ditt. Endre valget ditt, og prøv på nytt.
Denne driveren er ikke kompatibel
Denne driveren er ikke gjeldende for det valgte produktet. Velg et annet produkt for å angi produktopplysningene dine for denne driveren på nytt, eller gå til siden for produktstøtte for å vise alle drivere for et annet produkt.
Logg på Windows som administrator for å bruke automatisk skanning. Hvis du allerede er logget på som administrator og ser denne meldingen, må du starte maskinen på nytt.Systemet ditt blir administrert av IT-administratoren, og funksjonene kan være begrenset.
Finn flere oppdateringer. Bruk SupportAssist for å finne alle de nyeste driveroppdateringene for enheten din.
Feilrettinger og forbedringer
Fixes - Fixed issues where SSD may not be detected after a previous forced power cycle.
Enhancements - Enhanced the device ready time, allowing system to be able to power up quickly.
Dell Technologies anbefaler at du går gjennom denne oppdateringen for å finne ut om den gjelder for systemet ditt. Oppdateringen inneholder endringer som bare påvirker bestemte konfigurasjoner, eller som gir nye funksjoner som kanskje gjelder miljøet ditt.
1. Equipment needed, a CD drive, a blank CD. 2. Do not POWER OFF the system during the firmware update procedure. 3. Please perform a full system backup before starting the firmware update procedure (highly recommended). 4. Connect your notebook to a AC power supply during the firmware update procedure (highly recommended). 5.The firmware utility tool is OS independent.
Backup 1. It is highly recommended that full system backup be completed before starting this firmware upgrade procedure.
Download and image extraction 1. Click Download File to download the zipped file. 2. Extract the file into a folder. 3. The ISO image file is used to burn the utility onto a bootable CD.
Installation 1. Ensure that your notebook is plugged into a AC power supply during the update process (high recommended). 2. DO NOT remove power from the system during the firmware update process. 3. Ensure that your BIOS has been set to ATA or AHCI mode. DO NOT select RAID mode. This utility will not work in RAID mode. 4. Ensure that your BIOS boot order has been set up to boot from CD drive a. You can do so by either pressing F12 during the boot up and then select CD drive to boot from b. Or by pressing F2 during the boot up, enter the boot order selection and select CD drive to boot from. Save the setting before exiting. 5. Insert the bootable CD media with ISO image into your system. 6. Reboot the system from the bootable CD media, the firmware update utility will be started automatically. 7. Connected Micron SSD drive that is eligible for the firmware update will be shown on the screen. 8. Select Yes to the request 'Update firmware on this drive?' 9. DO NOT power off the system during the update process, the update will take about 30 to 60 seconds. Some systems may require a longer time to complete. 10. Upon completion, the message 'Current Firmware is: 040H' will be displayed.