LSI Logic Ultra 320 SCSI Adapter Non-RAID, v.1.9.11.0, A00
AUTOMATISK INSTALLERT Denne filen ble automatisk installert som en del av en nylig oppdatering. Hvis du opplever problemer, kan du laste ned og installere på nytt manuelt.Innholdet på denne siden kan ha blitt oversatt automatisk. Fyll ut skjemaet nederst på siden for å gi tilbakemelding.
LSI Logic PCI SCSI/FC MPI Driver for Windows 2003 v1.9.11.0
Anbefalt
Finn den beste nedlastingen for systemet
Angi produktdetaljer for å vise den nyeste driverinformasjonen for systemetStøtte for søk
Skriv inn Dell-service-ID-en eller -modellen
Ønsker du å finne produktet? Skriv inn en produktidentifikator. Vis meg hvordan
Denne driveren er ikke kompatibel
Denne driveren er ikke gjeldende for det valgte produktet. Velg et annet produkt for å angi produktopplysningene dine for denne driveren på nytt, eller gå til siden for produktstøtte for å vise alle drivere for et annet produkt.
Logg på Windows som administrator for å bruke automatisk skanning. Hvis du allerede er logget på som administrator og ser denne meldingen, må du starte maskinen på nytt. Systemet ditt blir administrert av IT-administratoren, og funksjonene kan være begrenset.
Finn flere oppdateringer. Bruk SupportAssist for å finne alle de nyeste driveroppdateringene for enheten din.
Feilrettinger og forbedringer
Initial Release
Les merVersjon
1.9.11.0, A00
Utgivelsesdato
22 nov. 2007
Nedlastingstype
Driver
Kategori
SCSI uten RAID
Viktighet
AnbefaltDell Technologies anbefaler at du installerer denne oppdateringen ved neste planlagte oppdatering. Oppdateringen inneholder endringer for å opprettholde den generelle systemtilstanden. Det sikrer at systemprogramvaren forblir oppdatert og kompatibel med andre systemmoduler (fastvare, BIOS, drivere og programvare) og kan inkludere andre nye funksjoner.
Tilgjengelige formater Se viktig informasjon:
Filformat: Pakker ut filer direkte til lokal disk
Filnavn: MD2K3A00.exe
Filstørrelse: 65 KB
Dette er en stor fil. Avhengig av tilkoblingshastigheten kan det ta litt tid å laste den ned.
Formatbeskrivelse:
Dette filformatet er et arkiv med filer som kan pakkes ut til en mappe på harddisken. Deretter installerer du fra den mappen.
Kontroller kontrollsumverdien for å sikre integriteten til nedlastingen.
MD5:
Ikke tilgjengelig
SHA1:
Ikke tilgjengelig
SHA-256:
Ikke tilgjengelig
Ved å laste ned godtar du vilkårene i lisensavtalen for Dell-programvare. (på engelsk)
Viktig informasjon
This driver is compatible with LSI 1020/1030 SCSI controllers and is intended for use with Windows 2003 Server, Enterprise Edition Server, Web Server, Small Business Server and Datacenter Server.
Since the 1020/1030 BIOS/FW is delivered as part of the System BIOS, it is highly recommended that you have the latest available System BIOS (also available from Dell support) already installed on your system before updating this driver
Since the 1020/1030 BIOS/FW is delivered as part of the System BIOS, it is highly recommended that you have the latest available System BIOS (also available from Dell support) already installed on your system before updating this driver
Operativsystemer som støttes
Windows Server 2003
Gjelder
Ultra 320 SCSI Adapter Non-RAID
Instruksjoner for installasjon
Custom Instructions for MD2K3A00.exe:
Download
1. Click Download Now, to download the file.
2. If the Export Compliance Disclaimer window appears, click Yes, I Accept this Agreement.
3. When the File Download window appears, click Save and click OK. The Save In: window appears.
4. From the Save In: field, click the down arrow then click to select Desktop and click Save. The file will download to your desktop.
5. If the Download Complete window appears, click Close. The file icon appears on your desktop.
Diskette Creation
1. Insert a floppy diskette into the floppy drive.
2. Double-click the new icon on the desktop. The Self-Extractor window appears.
3. Specify the floppy drive as the location to unzip the files.
4. Click on the unzip button to extract files.
IMPORTANT NOTE: If you are running Open Manage Array Manager v3.2 or higher under Windows 2003, to avoid a potential Blue Screen, prior to updating the driver you will need to:
1. Disable the SCSI subsystem provider in the Array Manager Utilities before upgrading the driver. Please refer to the Array Manager documentation for details on how to do this.
2. Once the SCSI provider is disabled, you should then navigate to the \WINDOWS\SYSTEM32\DRIVERS folder and temporarily rename ASPI32.SYS to ASPI32.XXX, then reboot the system before proceeding with the upgrade.
3. Following the upgrade, you will need to reboot again before re-naming ASPI32.SYS back to its' original name, then finally re-enabling the SCSI provider.
Updating the driver on an Existing Windows 2003 Server
*NOTE: You must be logged on as Administrator or have administrative privileges to perform these steps:
1. Copy files extracted above to formatted floppy disk
2. From the desktop, right-click the My Computer icon.
3. Left-click Manage.
4. Click Device Manager.
5. Double-click SCSI and RAID controllers (A List of all currently installed SCSI controllers appears) - in the case of a dual channel controller, there will be two devices listed (one for each channel).The driver will have to be updated separately for each channel.
6. Double-click the appropriate SCSI controller (such as 'LSI Logic 1020/1030 Ultra320 SCSI Adapter').
7. Select the Driver tab.
8. Select Update Driver. (The Hardware Update Wizard appears).
9. Choose 'Install from a list of specific locations" and click Next.
10. Choose 'Don't Search. I will choose the driver to install"
11. Click Next.
12. Click 'Have Disk' button. (The 'Install from Disk' dialog appears).
13. Insert the driver diskette created above. (Skip this step if installing driver from location on hard drive)
14. Click 'Browse' button (Locate File dialog appears).
15. Use pull-down box to find floppy drive or location on hard drive where you previously extracted files.
16. Once the correct path appears in the dropdown box, 'symmpi.inf' should appear in 'File Name' box - if not, select it.
17. Click 'Open' button ('Install From Disk' dialog reappears with correct path displayed).
18. Click 'OK' (Upgrade Device Driver Wizard reappears).
19. Choose 'LSI Logic 1020/1030 Ultra320 SCSI Adapter'
20. Click 'Next'
21. Click 'Next' again to confirm choice and upgrade driver
22. Close Wizard by clicking Finish
23. Close Properties Dialog for device.
24. Do not reboot system yet if prompted to do so.
25. Repeat steps 5-23 for second channel after Device Manager refreshes.
26. Reboot System to complete upgrade.
Adding the LSI Logic SCSI Driver to an Existing Windows 2003 Server (non-upgrade) - *NOTE* this will only apply if the SCSI controller was previously disabled in system BIOS setup, and you have enabled it for the first time - otherwise, follow the update instructions above:
1) Boot the system to Windows 2003. The 'Found New Hardware' Wizard displays.
2) Select 'Search for a suitable driver' and select 'Next' to continue.
3) Select 'Floppy disk drive', insert the LSI Logic Windows 2003 SCSI driver disket
Download
1. Click Download Now, to download the file.
2. If the Export Compliance Disclaimer window appears, click Yes, I Accept this Agreement.
3. When the File Download window appears, click Save and click OK. The Save In: window appears.
4. From the Save In: field, click the down arrow then click to select Desktop and click Save. The file will download to your desktop.
5. If the Download Complete window appears, click Close. The file icon appears on your desktop.
Diskette Creation
1. Insert a floppy diskette into the floppy drive.
2. Double-click the new icon on the desktop. The Self-Extractor window appears.
3. Specify the floppy drive as the location to unzip the files.
4. Click on the unzip button to extract files.
IMPORTANT NOTE: If you are running Open Manage Array Manager v3.2 or higher under Windows 2003, to avoid a potential Blue Screen, prior to updating the driver you will need to:
1. Disable the SCSI subsystem provider in the Array Manager Utilities before upgrading the driver. Please refer to the Array Manager documentation for details on how to do this.
2. Once the SCSI provider is disabled, you should then navigate to the \WINDOWS\SYSTEM32\DRIVERS folder and temporarily rename ASPI32.SYS to ASPI32.XXX, then reboot the system before proceeding with the upgrade.
3. Following the upgrade, you will need to reboot again before re-naming ASPI32.SYS back to its' original name, then finally re-enabling the SCSI provider.
Updating the driver on an Existing Windows 2003 Server
*NOTE: You must be logged on as Administrator or have administrative privileges to perform these steps:
1. Copy files extracted above to formatted floppy disk
2. From the desktop, right-click the My Computer icon.
3. Left-click Manage.
4. Click Device Manager.
5. Double-click SCSI and RAID controllers (A List of all currently installed SCSI controllers appears) - in the case of a dual channel controller, there will be two devices listed (one for each channel).The driver will have to be updated separately for each channel.
6. Double-click the appropriate SCSI controller (such as 'LSI Logic 1020/1030 Ultra320 SCSI Adapter').
7. Select the Driver tab.
8. Select Update Driver. (The Hardware Update Wizard appears).
9. Choose 'Install from a list of specific locations" and click Next.
10. Choose 'Don't Search. I will choose the driver to install"
11. Click Next.
12. Click 'Have Disk' button. (The 'Install from Disk' dialog appears).
13. Insert the driver diskette created above. (Skip this step if installing driver from location on hard drive)
14. Click 'Browse' button (Locate File dialog appears).
15. Use pull-down box to find floppy drive or location on hard drive where you previously extracted files.
16. Once the correct path appears in the dropdown box, 'symmpi.inf' should appear in 'File Name' box - if not, select it.
17. Click 'Open' button ('Install From Disk' dialog reappears with correct path displayed).
18. Click 'OK' (Upgrade Device Driver Wizard reappears).
19. Choose 'LSI Logic 1020/1030 Ultra320 SCSI Adapter'
20. Click 'Next'
21. Click 'Next' again to confirm choice and upgrade driver
22. Close Wizard by clicking Finish
23. Close Properties Dialog for device.
24. Do not reboot system yet if prompted to do so.
25. Repeat steps 5-23 for second channel after Device Manager refreshes.
26. Reboot System to complete upgrade.
Adding the LSI Logic SCSI Driver to an Existing Windows 2003 Server (non-upgrade) - *NOTE* this will only apply if the SCSI controller was previously disabled in system BIOS setup, and you have enabled it for the first time - otherwise, follow the update instructions above:
1) Boot the system to Windows 2003. The 'Found New Hardware' Wizard displays.
2) Select 'Search for a suitable driver' and select 'Next' to continue.
3) Select 'Floppy disk drive', insert the LSI Logic Windows 2003 SCSI driver disket
Hjelp og veiledninger for drivere
Hvis du vil ha flere nedlastinger, kan du gå til Drivere og nedlastinger. For å få hjelp til å bruke informasjonen på denne siden, kan du gå til Driverhjelp og opplæring