Dell SAS Hard Drive Firmware Utility, SATA Hard Drive Firmware Utility, v.SAS_SATA, A30
AUTOMATISK INSTALLERTDenne filen ble automatisk installert som en del av en nylig oppdatering. Hvis du opplever problemer, kan du laste ned og installere på nytt manuelt.
Innholdet på denne siden kan ha blitt oversatt automatisk. Fyll ut skjemaet nederst på siden for å gi tilbakemelding.
Denne filen ble automatisk installert som en del av en nylig oppdatering. Hvis du opplever problemer, kan du laste ned og installere på nytt manuelt.
This is a general maintenance release for SAS and SATA drives. It is a re-release of the previous version with additional firmware updates.
Anbefalt
Finn den beste nedlastingen for systemet
Angi produktdetaljer for å vise den nyeste driverinformasjonen for systemet
Støtte for søk
Skriv inn Dell-service-ID-en eller -modellen
Ønsker du å finne produktet? Skriv inn en produktidentifikator.Vis meg hvordan
Finner ingen resultater. Vi finner ikke noe for søket ditt. Endre valget ditt, og prøv på nytt.
Denne driveren er ikke kompatibel
Denne driveren er ikke gjeldende for det valgte produktet. Velg et annet produkt for å angi produktopplysningene dine for denne driveren på nytt, eller gå til siden for produktstøtte for å vise alle drivere for et annet produkt.
Logg på Windows som administrator for å bruke automatisk skanning. Hvis du allerede er logget på som administrator og ser denne meldingen, må du starte maskinen på nytt.Systemet ditt blir administrert av IT-administratoren, og funksjonene kan være begrenset.
Finn flere oppdateringer. Bruk SupportAssist for å finne alle de nyeste driveroppdateringene for enheten din.
Feilrettinger og forbedringer
Fixes/Enhancements:
The Hitachi SAS release for 15K 3.5" SAS hard drive firmware to fix Linux install hang in a RAID-0 config. During a Linux install small block sequential writes occur which brings out this bug and result in a hang during install when attached to SAS-5/iR running in RAID 0. The firmware will rev from A48B to A5F0.
Dell Technologies anbefaler at du installerer denne oppdateringen ved neste planlagte oppdatering. Oppdateringen inneholder endringer for å opprettholde den generelle systemtilstanden. Det sikrer at systemprogramvaren forblir oppdatert og kompatibel med andre systemmoduler (fastvare, BIOS, drivere og programvare) og kan inkludere andre nye funksjoner.
Dette er en stor fil. Avhengig av tilkoblingshastigheten kan det ta litt tid å laste den ned.
Formatbeskrivelse:
Denne filen inneholder et komprimert (zippet) sett med filer. Last ned filen til en mappe på harddisken, og åpne den (dobbeltklikk) for å pakke ut settet med filer. Følg instruksjonene for å fullføre installeringen.
"This release is intended for use on drives attached to SAS/ PERC controllers and MD1000, MD1120, MD1200 and MD1220 Enclosures. To update drives attached to MD3000 and MD3000i enclosures, use R291590"
Please note: Only Dell Branded SAS/SCSI, PERC and embedded ICH controllers are supported.
On drives attached to PERC5/PERC6 controllers, the first drive to be updated requires a 5 minute delay before firmware flash to begin. Do not power cycle or reboot your system while the update is in progress.
1. Click the "Download Now" link to download the file. 2. When the File Download window appears, click "Save" to save the file to your hard drive.
Installation
1. Browse to the location where you downloaded the file and double-click the new file. 2. Read over the release information presented in the dialog window. 3. Download and install any prerequisites identified in the dialog window before proceeding. 4. Click the Install button. 5. Follow the remaining prompts to perform the update.
Detailed Instructions
1) Click Download now. The File Download window appears.
2) Click the Save button. The Save As window appears.
3) Select Desktop using the drop-down menu to the right of Save in.
4) Click the Save button. A progress meter moves as the download is completed.
5) If necessary, click X in the upper right-hand corner of the Download Progress Window to close it upon completion.
6) Double click the Icon on your desktop for the newly saved file.