Dell SAS Hard Drive Firmware Utility, SATA Hard Drive Firmware Utility, v.Seagate SAS, A00
AUTOMATISK INSTALLERT Denne filen ble automatisk installert som en del av en nylig oppdatering. Hvis du opplever problemer, kan du laste ned og installere på nytt manuelt.Innholdet på denne siden kan ha blitt oversatt automatisk. Fyll ut skjemaet nederst på siden for å gi tilbakemelding.
Seagate drives not seen during SMTD installation or after adding additional drives online
in Linux. This is a special release targeted only for 5 Seagate SAS drives listed in the Fixes and Enhancements section.
R211868 is intended for all other firmware updates.
in Linux. This is a special release targeted only for 5 Seagate SAS drives listed in the Fixes and Enhancements section.
R211868 is intended for all other firmware updates.
Anbefalt
Finn den beste nedlastingen for systemet
Angi produktdetaljer for å vise den nyeste driverinformasjonen for systemetStøtte for søk
Skriv inn Dell-service-ID-en eller -modellen
Ønsker du å finne produktet? Skriv inn en produktidentifikator. Vis meg hvordan
Denne driveren er ikke kompatibel
Denne driveren er ikke gjeldende for det valgte produktet. Velg et annet produkt for å angi produktopplysningene dine for denne driveren på nytt, eller gå til siden for produktstøtte for å vise alle drivere for et annet produkt.
Logg på Windows som administrator for å bruke automatisk skanning. Hvis du allerede er logget på som administrator og ser denne meldingen, må du starte maskinen på nytt. Systemet ditt blir administrert av IT-administratoren, og funksjonene kan være begrenset.
Finn flere oppdateringer. Bruk SupportAssist for å finne alle de nyeste driveroppdateringene for enheten din.
Feilrettinger og forbedringer
Several Seagate drives shipped from Dell factories between February 2nd and February 20th may experience the following symptoms:
A) During an install from System Management Tool and Documentation DVD:
1. If there is no RAID config from ctrl-r and the DVD is booted it will display a blank white screen where there should be array configuration setup.
2. If there is a RAID config from ctrl-r already present on the drives, it will boot to the SMTD DVD but skip the RAID config screen. The menu item for RAID config in the left window will not appear in the action list. Install can be completed using this method.
B) Enclosure or server hard drives are being configured or added in an existing Linux install:
The drives my not be seen in the Linux browser that is using Open Manage Storage Management to configure the drives. Or, the Vendor ID for the disk drive may appear with garbled characters.
The FW version on the drive label will represent the correct firmware version; however, a later version was flashed to the drive in the factory.
Affected drives:
Family Part # Right FW Wrong FW
Maverick XT764 SM04 SM07
Maverick RN829 SM04 SM07
Firebird HT952 S229 S22B
Firebird CM318 S229 S22B
Timberland T-10 GY582 T211 T213
Timberland T-10 HT954 T211 T213
Timberland T-10 HT938 T211 T213
Timberland NS GY583 NS25 NS27
Timberland 15K5 GY581 S528 S529
Timberland 15K5 HT953 S528 S529
Timberland 15K5 TN937 S528 S529
Les merA) During an install from System Management Tool and Documentation DVD:
1. If there is no RAID config from ctrl-r and the DVD is booted it will display a blank white screen where there should be array configuration setup.
2. If there is a RAID config from ctrl-r already present on the drives, it will boot to the SMTD DVD but skip the RAID config screen. The menu item for RAID config in the left window will not appear in the action list. Install can be completed using this method.
B) Enclosure or server hard drives are being configured or added in an existing Linux install:
The drives my not be seen in the Linux browser that is using Open Manage Storage Management to configure the drives. Or, the Vendor ID for the disk drive may appear with garbled characters.
The FW version on the drive label will represent the correct firmware version; however, a later version was flashed to the drive in the factory.
Affected drives:
Family Part # Right FW Wrong FW
Maverick XT764 SM04 SM07
Maverick RN829 SM04 SM07
Firebird HT952 S229 S22B
Firebird CM318 S229 S22B
Timberland T-10 GY582 T211 T213
Timberland T-10 HT954 T211 T213
Timberland T-10 HT938 T211 T213
Timberland NS GY583 NS25 NS27
Timberland 15K5 GY581 S528 S529
Timberland 15K5 HT953 S528 S529
Timberland 15K5 TN937 S528 S529
Versjon
Seagate SAS, A00
Utgivelsesdato
23 aug. 2012
Nedlastingstype
Fastvare
Kategori
Lagring
Viktighet
AnbefaltDell Technologies anbefaler at du installerer denne oppdateringen ved neste planlagte oppdatering. Oppdateringen inneholder endringer for å opprettholde den generelle systemtilstanden. Det sikrer at systemprogramvaren forblir oppdatert og kompatibel med andre systemmoduler (fastvare, BIOS, drivere og programvare) og kan inkludere andre nye funksjoner.
Tilgjengelige formater Se viktig informasjon:
Filformat: Ekstern ZIP-pakke
Filnavn: DELL_MULTI-DEVICE_A00_R212231.exe
Filstørrelse: 5.15 MB
Dette er en stor fil. Avhengig av tilkoblingshastigheten kan det ta litt tid å laste den ned.
Formatbeskrivelse:
Denne filen inneholder et komprimert (zippet) sett med filer. Last ned filen til en mappe på harddisken, og åpne den (dobbeltklikk) for å pakke ut settet med filer. Følg instruksjonene for å fullføre installeringen.
Kontroller kontrollsumverdien for å sikre integriteten til nedlastingen.
MD5:
07a889d1d650e647303195565a48482d
SHA1:
f396db7f37687f51554f9eb462731444fac94725
SHA-256:
50ba59ffee6da32cccca3a521962146e1ec89ba8465b000d78b751c07af10fb7
Ved å laste ned godtar du vilkårene i lisensavtalen for Dell-programvare. (på engelsk)
Viktig informasjon
This release is intended for use on drives attached to SAS/ PERC controllers and MD1000 Enclosures.
Please note: Only Dell Branded SAS/SCSI and PERC controllers are supported. Embedded SATA controllers are not supported.
On drives attached to PERC5/PERC6 controllers, the first drive to be updated requires a 5 minute delay before firmware flash to begin. Do not power cycle or reboot your system while the update is in progress.
Please note: Only Dell Branded SAS/SCSI and PERC controllers are supported. Embedded SATA controllers are not supported.
On drives attached to PERC5/PERC6 controllers, the first drive to be updated requires a 5 minute delay before firmware flash to begin. Do not power cycle or reboot your system while the update is in progress.
Operativsystemer som støttes
Ikke tilgjengelig
Gjelder
Dell SAS/SATA Hard Drive
Instruksjoner for installasjon
Download
1. Click the "Download Now" link to download the file.
2. When the File Download window appears, click "Save" to save the file to your hard drive.
Installation
1. Browse to the location where you downloaded the file and double-click the new file.
2. Read over the release information presented in the dialog window.
3. Download and install any prerequisites identified in the dialog window before proceeding.
4. Click the Install button.
5. Follow the remaining prompts to perform the update.
1) Click Download now.
The File Download window appears.
2) Click the Save button.
The Save As window appears.
3) Select Desktop using the drop-down menu to the right of Save in.
4) Click the Save button.
A progress meter moves as the download is completed.
5) If necessary, click X in the upper right-hand corner of the Download Progress Window to close it upon completion.
6) Double click the Icon on your desktop for the newly saved file.
The Dell Bios Release Notes window appears.
1. Click the "Download Now" link to download the file.
2. When the File Download window appears, click "Save" to save the file to your hard drive.
Installation
1. Browse to the location where you downloaded the file and double-click the new file.
2. Read over the release information presented in the dialog window.
3. Download and install any prerequisites identified in the dialog window before proceeding.
4. Click the Install button.
5. Follow the remaining prompts to perform the update.
1) Click Download now.
The File Download window appears.
2) Click the Save button.
The Save As window appears.
3) Select Desktop using the drop-down menu to the right of Save in.
4) Click the Save button.
A progress meter moves as the download is completed.
5) If necessary, click X in the upper right-hand corner of the Download Progress Window to close it upon completion.
6) Double click the Icon on your desktop for the newly saved file.
The Dell Bios Release Notes window appears.
Hjelp og veiledninger for drivere
Hvis du vil ha flere nedlastinger, kan du gå til Drivere og nedlastinger. For å få hjelp til å bruke informasjonen på denne siden, kan du gå til Driverhjelp og opplæring