Omstart krevesAUTOMATISK INSTALLERTDenne filen ble automatisk installert som en del av en nylig oppdatering. Hvis du opplever problemer, kan du laste ned og installere på nytt manuelt.
Innholdet på denne siden kan ha blitt oversatt automatisk. Fyll ut skjemaet nederst på siden for å gi tilbakemelding.
Denne filen ble automatisk installert som en del av en nylig oppdatering. Hvis du opplever problemer, kan du laste ned og installere på nytt manuelt.
This package provides the new firmware for power supplier and is supported on LiteOn 1100W PSU (PN: GYH9V) running on the Windows and Linux operating systems.
Anbefalt
Finn den beste nedlastingen for systemet
Angi produktdetaljer for å vise den nyeste driverinformasjonen for systemet
Støtte for søk
Skriv inn Dell-service-ID-en eller -modellen
Ønsker du å finne produktet? Skriv inn en produktidentifikator.Vis meg hvordan
Finner ingen resultater. Vi finner ikke noe for søket ditt. Endre valget ditt, og prøv på nytt.
Denne driveren er ikke kompatibel
Denne driveren er ikke gjeldende for det valgte produktet. Velg et annet produkt for å angi produktopplysningene dine for denne driveren på nytt, eller gå til siden for produktstøtte for å vise alle drivere for et annet produkt.
Logg på Windows som administrator for å bruke automatisk skanning. Hvis du allerede er logget på som administrator og ser denne meldingen, må du starte maskinen på nytt.Systemet ditt blir administrert av IT-administratoren, og funksjonene kan være begrenset.
Finn flere oppdateringer. Bruk SupportAssist for å finne alle de nyeste driveroppdateringene for enheten din.
Dell Technologies anbefaler at du går gjennom denne oppdateringen for å finne ut om den gjelder for systemet ditt. Oppdateringen inneholder endringer som bare påvirker bestemte konfigurasjoner, eller som gir nye funksjoner som kanskje gjelder miljøet ditt.
Dette er en stor fil. Avhengig av tilkoblingshastigheten kan det ta litt tid å laste den ned.
Formatbeskrivelse:
Dells oppdateringspakker (DUP) i Microsoft Windows 32-bitersformat er utformet for å kjøre på Microsoft Windows 64-biters operativsystemer. Dells oppdateringspakker (DUP) i Microsoft Windows 64-bitersformat kan bare kjøre på Microsoft Windows 64-biters operativsystemer. Når du velger en enhetsdriveroppdatering, må du velge en som passer til operativsystemet.
Dette er en stor fil. Avhengig av tilkoblingshastigheten kan det ta litt tid å laste den ned.
Formatbeskrivelse:
Dells oppdateringspakker for Linux kan brukes som frittstående programmer som sikrer at bestemte valideringskriterier er oppfylt, og deretter bruker en oppdatering. Merk: Oppdateringspakker for Linux har åpen kildekode. Du finner mer informasjon i Dells oppdateringspakker for Viktig-filen i Linux.
IMPORTANT: After a successful power supply firmware download, the managed system turns off for a duration ranging from three to ten minutes to continue updating the firmware. Once the firmware update is complete, the managed system reboots automatically.
CAUTION! Performing an AC power cycle or cold boot during a power supply firmware update, forces the power supply unit into an irrecoverable state and the managed system does not boot.
CAUTION: Performing an AC power cycle or cold boot during a power supply firmware update, forces the power supply unit (PSU) into an irrecoverable state and the managed system does not boot.
IMPORTANT: After a successful power supply firmware download, the managed system turns off for a duration ranging from three to twenty minutes to continue updating the firmware. It is imperative not to interrupt/restart manually during this time. Update time can vary but should be approximately 10 minutes. Margin should be added to assure the Dell Update Package (DUP) is not interrupted (some DUPs may take up to 20 minutes). Once the firmware update is complete, the managed system reboots automatically.
Instructions for ".BIN" file:
Download 1. Click the Download Now link to download the file. 2. When the "File Download" window appears, click Save to save the file to your hard drive.
Installation 1. Read the release information presented by executing the".BIN" file with "--version" command from the shell. 2. Download and install any prerequisites identified in the above step before proceeding. 3. Run the update by executing ".BIN" file from the shell. 4. Follow the remaining prompts to perform the update. 5. Upon successful completion the DUP will prompt to reboot system. 6. Restart your system. After the system restarts, DUP will enter USC to complete the flashing of the PSU firmware. 7. The actual flash begins after DUP exits USC. Please do not power off or power cycle the system as this can result in a non-functional power supply. 8. Once the flashing process is complete the system should power back up and boot to OS.
Instructions for ".EXE" file:
Download 1. Click the "Download Now" link to download the file. 2. When the "File Download" window appears, click "Save" to save the file to your hard drive.
Installation 1. Browse to the location where you downloaded the file and double-click the new file. 2. Read the release information presented in the dialog window. 3. Download and install any prerequisites identified in the dialog window before proceeding. 4. Click the Install button. 5. Follow the remaining prompts to perform the update. 6. Upon successful completion the DUP will prompt to reboot system. 7. Restart your system. After the system restarts, DUP will enter USC to complete the flashing of the PSU firmware. 8. The actual flash begins after DUP exits USC. Please do not power off or power cycle the system as this can result in a non-functional power supply. 9. Once the flashing process is complete the system should power back up and boot to OS.
GnuPG Signature of Dell Update Package Instructions for ".sign" file:
Download 1. Click the "Download Now" link to download the file. 2. When the "File Download" window appears, click "Save" to save the file to your hard drive.
Installation 1. Import the Dell public key. (You only need to import once on your system.) 2. Verify the Dell Update Package by using its signature file. 3. Upon successful completion the DUP will prompt to reboot system. 4. Restart your system. After the system restarts, DUP will enter USC to complete the flashing of the PSU firmware. 5. The actual flash begins after DUP exits USC. Please do not power off or power cycle the system as this can result in a non-functional power supply. 6. Once the flashing process is complete the system should power back up and boot to OS. IMPORTANT: After a successful power supply firmware download, the managed system turns off for a duration ranging from three to ten minutes to continue updating the firmware. Once the firmware update is complete, the managed system reboots automatically.
CAUTION! Performing an AC power cycle or cold boot during a power supply firmware update, forces the power supply unit into an irrecoverable state and the managed system does not boot.