AUTOMATISK INSTALLERTDenne filen ble automatisk installert som en del av en nylig oppdatering. Hvis du opplever problemer, kan du laste ned og installere på nytt manuelt.
Innholdet på denne siden kan ha blitt oversatt automatisk. Fyll ut skjemaet nederst på siden for å gi tilbakemelding.
Denne filen ble automatisk installert som en del av en nylig oppdatering. Hvis du opplever problemer, kan du laste ned og installere på nytt manuelt.
PowerVault 35F, firmware d9913d
Anbefalt
Finn den beste nedlastingen for systemet
Angi produktdetaljer for å vise den nyeste driverinformasjonen for systemet
Støtte for søk
Skriv inn Dell-service-ID-en eller -modellen
Ønsker du å finne produktet? Skriv inn en produktidentifikator.Vis meg hvordan
Finner ingen resultater. Vi finner ikke noe for søket ditt. Endre valget ditt, og prøv på nytt.
Denne driveren er ikke kompatibel
Denne driveren er ikke gjeldende for det valgte produktet. Velg et annet produkt for å angi produktopplysningene dine for denne driveren på nytt, eller gå til siden for produktstøtte for å vise alle drivere for et annet produkt.
Logg på Windows som administrator for å bruke automatisk skanning. Hvis du allerede er logget på som administrator og ser denne meldingen, må du starte maskinen på nytt.Systemet ditt blir administrert av IT-administratoren, og funksjonene kan være begrenset.
Finn flere oppdateringer. Bruk SupportAssist for å finne alle de nyeste driveroppdateringene for enheten din.
Feilrettinger og forbedringer
This release resolves a Netware issue in which the Veritas Backup Exec v8.5 startup sequence may hang with "Initializing Tape Hardware" when configured in a shared storage (SSO) environment.
Dell Technologies anbefaler at du går gjennom denne oppdateringen for å finne ut om den gjelder for systemet ditt. Oppdateringen inneholder endringer som bare påvirker bestemte konfigurasjoner, eller som gir nye funksjoner som kanskje gjelder miljøet ditt.
Dette er en stor fil. Avhengig av tilkoblingshastigheten kan det ta litt tid å laste den ned.
Formatbeskrivelse:
Denne filen inneholder et komprimert (zippet) sett med filer. Last ned filen til en mappe på harddisken, og åpne den (dobbeltklikk) for å pakke ut settet med filer. Følg instruksjonene for å fullføre installeringen.
The PowerVault 35F can either use FTP, TFTP or a serial connection (using the XMODEM protocol) to update the firmware. In order to update the firmware via the serial connection, the PowerVault 35F must be connected to a terminal emulation program supporting XMODEM transfers. This menu item does not appear when accessing the configuration menus through Telnet.
1. Download and run the file D9913D.EXE. This will extract the contents of the archive to a temporary directory (i.e. x:\Dell\Drivers\PV35F\).
2. Decide the method for firmware download (FTP, TFTP, or Serial Connection) and proceed to the appropriate instructions.
FTP Method
1. Make sure your PowerVault 35F is connected to a network and the IP address is set properly.
2. Start your FTP program using the PowerVault 35F’ s IP address. Type ftp (IP address).
NOTE: The default IP address is 1.1.1.1. See your PowerVault 35F User’s Manual for instructions on changing the IP address.
3. Use root as the user name and password as the password.
NOTE: This is the default user name and password for the PowerVault 35F. If you have changed the user name or password, then use the updated settings in place of the default settings.
4. Specify binary mode by typing bin.
5. Specify the firmware’s path and filename with the put command. Type put (path:filename).
The file will transfer and the PowerVault 35F will reboot. The PowerVault 35F is now using the new firmware.
NOTE: You may want to confirm the new firmware level by checking the PowerVault 35F’s reboot messages through the serial interface.
TFTP Method
1. Make sure your PowerVault 35F is connected to a network and the IP address is set properly.
2. At the command line, type the following tftp -i (IP address) put (path:filename).
The file transfer process will begin. The PowerVault 35F will automatically reboot upon completion of the download.
NOTE: You may want to confirm the new firmware level by checking the PowerVault 35F’ s reboot messages through the serial interface.
Serial Port (Terminal Emulator)
NOTE: For quicker downloading, configure the PowerVault 35F and the terminal emulator utility session connected to it (such as Hyperterminal) to run at 115200.
1. Establish a Serial Connection to the PowerVault 35F. Refer to the PowerVault 35F User’s Manual for the serial port settings.
2. From the Advanced Options menu, select the Download a new revision of the Firmware command to start the download procedure.
3. When you confirm the download, the PowerVault 35F will start the download process.
4. Use the Transfer -> Send File option in the terminal emulator utility.
5. Select the location of the firmware. Use the Browse button, if you need help locating the firmware file.
6. Make sure you select XMODEM as the protocol.
7. Press the Send button.
8. The firmware will begin to download.
When the download is complete, the system verifies that the firmware image was successfully written to the FLASH memory and then reboots the PowerVault 35F. Upon reboot, the PowerVault 35F detects that there is a newly downloaded firmware image and copies that image to the boot sector of the FLASH and then boots with that image. At that point the PowerVault 35F is using the new firmware image.