ZAINSTALOWANO AUTOMATYCZNIEPlik został automatycznie zainstalowany w ramach ostatniej aktualizacji. Jeśli występują jakiekolwiek problemy, możesz pobrać i ponownie zainstalować program ręcznie.
Zawartość tej strony mogła zostać automatycznie przetłumaczona. Aby przekazać opinię, wypełnij formularz znajdujący się w dolnej części strony.
Plik został automatycznie zainstalowany w ramach ostatniej aktualizacji. Jeśli występują jakiekolwiek problemy, możesz pobrać i ponownie zainstalować program ręcznie.
PERC 4/Di Device Driver for Red Hat Linux 7.2.
Polecane
Znajdź najlepsze pliki do pobrania dla swojego systemu
Wprowadź dane produktu, aby wyświetlić informacje o najnowszych sterownikach systemowych
Wyszukaj w zasobach wsparcia
Wprowadź kod Service Tag lub model produktu firmy Dell
Czy chcesz wyszukać produkt? Wprowadź identyfikator produktu.Pokaż jak
Nie znaleziono wyników. Nie udało się znaleźć wyszukiwanych informacji. Zmodyfikuj wyszukiwanie i spróbuj ponownie.
Ten sterownik jest niezgodny
Ten sterownik nie dotyczy wybranego produktu. Wybierz inny produkt, aby ponownie wprowadzić dane produktu dla tego sterownika, lub odwiedź stronę pomocy technicznej dotyczącej produktu, aby wyświetlić wszystkie sterowniki do innego produktu.
Zaloguj się do systemu Windows jako administrator, aby korzystać z funkcji automatycznego skanowania. Jeśli już zalogowano się jako administrator i ten komunikat jest widoczny, uruchom ponownie komputer.System jest zarządzany przez administratora IT, a jego funkcje mogą być ograniczone.
Znajdź więcej aktualizacji. Użyj narzędzia SupportAssist, aby wyszukać najnowsze aktualizacje sterowników swojego urządzenia.
Firma Dell Technologies zaleca sprawdzenie tej aktualizacji i ustalenie, czy dotyczy ona Twojego systemu. Aktualizacja zawiera zmiany wpływające tylko na niektóre konfiguracje lub oferuje nowe funkcje, które mogą, ale nie muszą mieć zastosowania w środowisku użytkownika.
Format pliku:Rozpakowuje pliki bezpośrednio na dysk lokalny
Nazwa pliku:perc4di-118c-72c.tar.gz
Rozmiar pliku:538.62 KB
Jest to duży plik. Jego pobranie może zająć trochę czasu, w zależności od szybkości połączenia.
Opis formatu:
Ten format pliku zawiera archiwum plików, które można zdekompresować do katalogu na dysku twardym. Z tego katalogu można następnie przeprowadzić instalację.
Instructions for downloading and creating driver diskette: ----------------------------------------------------------
You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
Download the file PERC4di-118c-72c.tar.gz to a temporary directory on your working system.
Extract the file to the floppy disk as follows:
1. On a Linux system:
Type the following commands under a Linux command shell: mount /dev/fd0 /mnt/floppy tar xvzf -C /mnt/floppy (Eg: /temp/PERC4di-118c-72c.tar.gz) umount /mnt/floppy
2. On a Microsoft Windows system:
You can use Winzip to extract tar.gz archives. However, note the following settings under Winzip to ensure correct extraction of the files.
Start Winzip -> Go to Options -> Configuration
Under the Miscellaneous tab make sure "TAR file smart CR/LF conversion" is unchecked.
Upon opening the tar.gz archive with Winzip, you get the following prompt:
'Archive contains one file. Should Winzip decompress it to a temporary folder and open it?'
Press 'yes' and extract the files normally under Winzip to the floppy drive.
Install Red Hat Linux 7.2 driver for PERC 4/Di as a boot controller -------------------------------------------------------
There are two ways of installing Red Hat 7.2 driver onto the PERC 4/Di as a boot controller. One is using a driver disk during OS installation and the second is using a driver (megaraid) RPM to update driver after OS is installed. The steps for both of these methods are provided below. All the files needed for both methods are included in the driver diskette created above.
For more detailed installation instructions of Red Hat 7.2, please refer to the OS installation guide at http://www.dell.com/linux.
I. Installing driver during OS installation: --------------------------------------------
1. Boot normally from the Redhat installation CD-Rom.
2. Type 'linux dd' on the boot prompt.
3. When the install prompts for a driver disk, insert the driver diskette created above and press 'Enter'.
4. Installation progresses normally. Continue until the 'Create Bootdisk' screen. Press CTRL-ALT-F2 to get to a shell window and type the following commands:
chroot /mnt/sysimage cd /boot /sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10 lilo ( only if lilo was used as bootloader. If grub used - skip this step ) exit
Press CTRL-ALT-F7 to get back to the install screen.
5. Complete the installation as directed by the install.
II. Update driver using RPMs after OS is installed --------------------------------------------------
Type the following commands under a Linux command shell:
mount /dev/fd0 /mnt/floppy cd /mnt/floppy ./megarpmwrapper.sh
Than follow the on-screen instructions to install the RPM driver.
For more detailed information about the script megarpmwrapper.sh, please refer to the release_notes.txt included in the release.