INSTALADO AUTOMATICAMENTEEste ficheiro foi instalado automaticamente como parte de uma atualização recente. Se detetar algum problema, pode transferir e reinstalar manualmente.
O conteúdo desta página pode ter sido traduzido automaticamente. Para fazer comentários, preencha o formulário no fim da página.
Este ficheiro foi instalado automaticamente como parte de uma atualização recente. Se detetar algum problema, pode transferir e reinstalar manualmente.
Dell PowerEdge RAID Controller 4/DC firmware and update script for for IA-64 based platforms. The update script runs under EFI.
Version: 351S
Recomendado
Encontre a melhor opção de download para seu sistema
Digite os dados do seu produto para ver as informações mais recentes sobre o driver do sistema
Pesquisar no suporte
Digite a etiqueta de serviço ou o modelo da Dell
Quer procurar o seu produto? Digite um identificador do produto.Mostre-me como
Nenhum resultado encontrado. Não foi possível encontrar resultados para a sua pesquisa. Modifique sua pesquisa e tente novamente.
Este driver não é compatível
Este driver não é válido para o produto selecionado. Selecione outro produto para digitar novamente os dados do seu produto para este driver ou acesse a página Suporte a produtos para ver todos os drivers de um produto diferente.
Faça log-in no Windows como administrador para usar a verificação automática. Se você já estiver conectado como administrador e estiver vendo esta mensagem, reinicialize o sistema.O sistema é gerenciado pelo administrador da TI e pode haver poucos recursos.
Encontre mais atualizações. Use o SupportAssist para encontrar as atualizações de driver mais recentes para o seu dispositivo.
Fixes & Enhancements
Current Firmware - 351S (Previous - 350O)
Current BIOS - 1.10 (Previous - 1.09)
Current Ctrl-M - U827 (Previous - U821)
Current Boot Block - 1.7.7Dell (Previous - 1.7.6Dell)
Fixes
1. Fixed an issue that optimized cache flush algorithms while switching between no read-ahead to read-ahead cache modes. 2. Modified the Fast Initialization function to delete all operation system partition table information. 3. Fixed an issue where a Seagate hard drive model M3637 was not negotiating correctly with PERC 4 adapters. 4. Fixed a SES Timeout error caused by a media error recovery defect in cluster mode on a PERC4/DC and a PERC3/DC. 5. Modified Ctrl-M to clear physical drive media error count upon drive replacement. Note: System must be powered on during the drive replacement in order for media errors to be cleared. 6. Modified caching algorithms to not switch from Write-back to Write-through during a battery fast charge. 7. Fixed a performance degradation issue when using RAID 10 virtual disks, when configured to use no read ahead or write caching and direct IO on PERC4 controllers.
Enhancements
1. Added Patrol Read feature. Patrol Read involves the review of the system for possible hard drive errors that could lead to drive failure, then action to correct the errors. The goal is to protect data integrity by detecting physical drive failures before the failures can damage data. Patrol Read adjusts the amount of RAID controller resources dedicated to Patrol Read operations based on outstanding disk I/O. 2. Added Rebuild Checkpoint feature. The Dell PERC firmware has a feature to resume a rebuild on a physical drive in case of an abrupt power loss or if the server rebooted in the middle of a rebuild operation. 3. Enhanced write algorithms to increase I/O performance for RAID 5 and RAID 50 virtual disks using four or more disks that are configured to use write-through write cache mode.
Firmware upgrade while controller is doing background I/O task: The firmware upgrade may fail if any of the RAID controllers in the system are performing an I/O background task. (ie. check consistency, background initialization, rebuild, or reconstruction). Allow the background task to complete before attempting to upgrade the firmware. Patrol Read tasks will not affect a firmware upgrade. Current RAID configuration will not be modified or cleared during the Firmware Upgrade process.
A Dell Technologies recomenda aplicar esta atualização durante o próximo ciclo de atualização programado. A atualização contém alterações para manter a integridade geral do sistema. Ela garante que os softwares do sistema fiquem atualizados e compatíveis com outros módulos do sistema (firmware, BIOS, drivers e software) e pode incluir outros recursos novos.
Este é um arquivo pesado. Dependendo da velocidade da sua conexão, o download pode demorar um tempo para ser concluído.
Descrição de formato:
Este arquivo contém um conjunto compactado (ou zipado) de arquivos. Faça download do arquivo em uma pasta no disco rígido e, em seguida, execute-o (dê dois cliques) para descompactar o conjunto de arquivos. Siga as instruções para concluir a instalação.
1. Click the Download Now link to download the file. 2. When the File Download window appears, click Save to save the file to your hard drive.
Extract Files 1. Browse to the location where you downloaded the file and double-click the new file to unzip the download package 2. Click Continue. 3. Specify the location to unzip the files. 4. Click on the OK button to extract files. After the files are extracted the message all files were successfully unzipped will appear. 5. Click the OK button to exit from the installer.
Installation
To update the firmware for your PERC 4/DC adapter, perform the following steps: 1. Extract the contents of the firmware package to your hardrive. 2. Copy the contents of the package to a formatted floppy disk, USB key, or CD-ROM. 3. Power on the server. From the EFI Boot Manager Menu, select EFI Shell. 4. Insert the media which contains the firmware update files from step 2. This may be a USB key, floppy diskette (a USB floppy drive may be used), or CD-ROM. 5. At the Shell> prompt, type 'map -r' to view all mounted devices. Locate the device which contains the firmware update files - it will be enumerated as fs0, fs1, ect. 6. To change to the proper device, type 'fs1:' NOTE: Your device may have a different file system number. 7. From the fs1:> prompt type 'percupd.nsh' to initiate the firmware update. 8. Follow the instructions from the EFI update tool to complete the firmware upgrade. 9. You will need to restart your system for the new firmware to take effect.
Custom Instructions for perc4dc-IA64-351S-A05.txt:
Download the readme file to view information about this release.