Dell PowerVault 35F, D9913D
INSTALADO AUTOMATICAMENTE Este ficheiro foi instalado automaticamente como parte de uma atualização recente. Se detetar algum problema, pode transferir e reinstalar manualmente.O conteúdo desta página pode ter sido traduzido automaticamente. Para fazer comentários, preencha o formulário no fim da página.
PowerVault 35F, firmware d9913d
Recomendado
Encontre a melhor opção de download para seu sistema
Digite os dados do seu produto para ver as informações mais recentes sobre o driver do sistemaPesquisar no suporte
Digite a etiqueta de serviço ou o modelo da Dell
Quer procurar o seu produto? Digite um identificador do produto. Mostre-me como
Este driver não é compatível
Este driver não é válido para o produto selecionado. Selecione outro produto para digitar novamente os dados do seu produto para este driver ou acesse a página Suporte a produtos para ver todos os drivers de um produto diferente.
Faça log-in no Windows como administrador para usar a verificação automática. Se você já estiver conectado como administrador e estiver vendo esta mensagem, reinicialize o sistema. O sistema é gerenciado pelo administrador da TI e pode haver poucos recursos.
Encontre mais atualizações. Use o SupportAssist para encontrar as atualizações de driver mais recentes para o seu dispositivo.
Fixes & Enhancements
This release resolves a Netware issue in which the Veritas Backup Exec
v8.5 startup sequence may hang with "Initializing Tape Hardware" when
configured in a shared storage (SSO) environment.
Ler maisv8.5 startup sequence may hang with "Initializing Tape Hardware" when
configured in a shared storage (SSO) environment.
Versão
d9913d, D9913D
Data da versão
06 fev. 2001
Tipo de download
Firmware
Category
Fibre Channel
Importance
OptionalA Dell Technologies recomenda analisar esta atualização para determinar se ela é válida para seu sistema. A atualização contém alterações que afetam apenas determinadas configurações ou oferece novos recursos que podem ou não ser válidos para seu ambiente.
Formatos disponíveis
File Format: ZipPack External
File Name: d9913d.exe
File Size: 601.37 KB
Este é um arquivo pesado. Dependendo da velocidade da sua conexão, o download pode demorar um tempo para ser concluído.
Descrição de formato:
Este arquivo contém um conjunto compactado (ou zipado) de arquivos. Faça download do arquivo em uma pasta no disco rígido e, em seguida, execute-o (dê dois cliques) para descompactar o conjunto de arquivos. Siga as instruções para concluir a instalação.
Para garantir a integridade do download, verifique o valor da soma de verificação.
MD5:
Não disponível
SHA1:
Não disponível
SHA-256:
Não disponível
Ao fazer o download, você aceita os termos do Contrato de Licença de Software da Dell. (em Inglês)
Instruções de instalação
PowerVault 35F Firmware Download Instructions
The PowerVault 35F can either use FTP, TFTP or a serial connection (using
the XMODEM protocol) to update the firmware. In order to update the
firmware via the serial connection, the PowerVault 35F must be connected
to a terminal emulation program supporting XMODEM transfers. This menu
item does not appear when accessing the configuration menus through Telnet.
1. Download and run the file D9913D.EXE. This will extract the contents
of the archive to a temporary directory (i.e. x:\Dell\Drivers\PV35F\).
2. Decide the method for firmware download (FTP, TFTP, or Serial
Connection) and proceed to the appropriate instructions.
FTP Method
1. Make sure your PowerVault 35F is connected to a network and the IP
address is set properly.
2. Start your FTP program using the PowerVault 35F’ s IP address. Type
ftp (IP address).
NOTE: The default IP address is 1.1.1.1. See your PowerVault 35F User’s
Manual for instructions on changing the IP address.
3. Use root as the user name and password as the password.
NOTE: This is the default user name and password for the PowerVault 35F.
If you have changed the user name or password, then use the updated
settings in place of the default settings.
4. Specify binary mode by typing bin.
5. Specify the firmware’s path and filename with the put command. Type
put (path:filename).
The file will transfer and the PowerVault 35F will reboot. The PowerVault
35F is now using the new firmware.
NOTE: You may want to confirm the new firmware level by checking the
PowerVault 35F’s reboot messages through the serial interface.
TFTP Method
1. Make sure your PowerVault 35F is connected to a network and the IP
address is set properly.
2. At the command line, type the following tftp -i (IP address) put
(path:filename).
The file transfer process will begin. The PowerVault 35F will
automatically reboot upon completion of the download.
NOTE: You may want to confirm the new firmware level by checking the
PowerVault 35F’ s reboot messages through the serial interface.
Serial Port (Terminal Emulator)
NOTE: For quicker downloading, configure the PowerVault 35F and the
terminal emulator utility session connected to it (such as Hyperterminal)
to run at 115200.
1. Establish a Serial Connection to the PowerVault 35F. Refer to the
PowerVault 35F User’s Manual for the serial port settings.
2. From the Advanced Options menu, select the Download a new revision of
the Firmware command to start the download procedure.
3. When you confirm the download, the PowerVault 35F will start the
download process.
4. Use the Transfer -> Send File option in the terminal emulator utility.
5. Select the location of the firmware. Use the Browse button, if you
need help locating the firmware file.
6. Make sure you select XMODEM as the protocol.
7. Press the Send button.
8. The firmware will begin to download.
When the download is complete, the system verifies that the firmware image
was successfully written to the FLASH memory and then reboots the
PowerVault 35F. Upon reboot, the PowerVault 35F detects that there is a
newly downloaded firmware image and copies that image to the boot sector
of the FLASH and then boots with that image. At that point the PowerVault
35F is using the new firmware image.
The PowerVault 35F can either use FTP, TFTP or a serial connection (using
the XMODEM protocol) to update the firmware. In order to update the
firmware via the serial connection, the PowerVault 35F must be connected
to a terminal emulation program supporting XMODEM transfers. This menu
item does not appear when accessing the configuration menus through Telnet.
1. Download and run the file D9913D.EXE. This will extract the contents
of the archive to a temporary directory (i.e. x:\Dell\Drivers\PV35F\).
2. Decide the method for firmware download (FTP, TFTP, or Serial
Connection) and proceed to the appropriate instructions.
FTP Method
1. Make sure your PowerVault 35F is connected to a network and the IP
address is set properly.
2. Start your FTP program using the PowerVault 35F’ s IP address. Type
ftp (IP address).
NOTE: The default IP address is 1.1.1.1. See your PowerVault 35F User’s
Manual for instructions on changing the IP address.
3. Use root as the user name and password as the password.
NOTE: This is the default user name and password for the PowerVault 35F.
If you have changed the user name or password, then use the updated
settings in place of the default settings.
4. Specify binary mode by typing bin.
5. Specify the firmware’s path and filename with the put command. Type
put (path:filename).
The file will transfer and the PowerVault 35F will reboot. The PowerVault
35F is now using the new firmware.
NOTE: You may want to confirm the new firmware level by checking the
PowerVault 35F’s reboot messages through the serial interface.
TFTP Method
1. Make sure your PowerVault 35F is connected to a network and the IP
address is set properly.
2. At the command line, type the following tftp -i (IP address) put
(path:filename).
The file transfer process will begin. The PowerVault 35F will
automatically reboot upon completion of the download.
NOTE: You may want to confirm the new firmware level by checking the
PowerVault 35F’ s reboot messages through the serial interface.
Serial Port (Terminal Emulator)
NOTE: For quicker downloading, configure the PowerVault 35F and the
terminal emulator utility session connected to it (such as Hyperterminal)
to run at 115200.
1. Establish a Serial Connection to the PowerVault 35F. Refer to the
PowerVault 35F User’s Manual for the serial port settings.
2. From the Advanced Options menu, select the Download a new revision of
the Firmware command to start the download procedure.
3. When you confirm the download, the PowerVault 35F will start the
download process.
4. Use the Transfer -> Send File option in the terminal emulator utility.
5. Select the location of the firmware. Use the Browse button, if you
need help locating the firmware file.
6. Make sure you select XMODEM as the protocol.
7. Press the Send button.
8. The firmware will begin to download.
When the download is complete, the system verifies that the firmware image
was successfully written to the FLASH memory and then reboots the
PowerVault 35F. Upon reboot, the PowerVault 35F detects that there is a
newly downloaded firmware image and copies that image to the boot sector
of the FLASH and then boots with that image. At that point the PowerVault
35F is using the new firmware image.
Ajuda e tutoriais para drivers
Para ver mais downloads, vá para Drivers e downloads. Para obter ajuda sobre como usar as informações contidas nesta página, visite Ajuda e tutoriais de driver.