INSTALATE AUTOMATAcest fișier a fost instalat automat ca parte a unei actualizări recente. Dacă întâmpinați orice probleme, puteți descărca și reinstala manual.
Conținutul acestei pagini este posibil să fi fost tradus automat. Pentru a furniza feedback, completați formularul din partea de jos a paginii.
Acest fișier a fost instalat automat ca parte a unei actualizări recente. Dacă întâmpinați orice probleme, puteți descărca și reinstala manual.
PERC 4/Di Device Driver for Red Hat Linux 7.2.
Recomandate
Găsiți cea mai bună descărcare pentru sistemul dvs.
Introduceți detaliile produsului pentru a vedea cele mai recente informații despre driverele sistemului dvs.
Asistență căutare
Introduceți eticheta de service Dell sau modelul
Doriți să vă căutați produsul? Introduceți un identificator de produs.Arătați-mi cum
No results found.We couldn't find anything for your search. Please modify your search and try again.
This driver is not compatible
This driver is not applicable for the selected product. Choose another product to re-enter your product details for this driver or visit the Product Support page to view all drivers for a different product.
Conectați-vă la Windows ca administrator pentru a utiliza scanarea automată. Dacă sunteți deja conectat ca administrator și vedeți acest mesaj, reporniți sistemul.Sistemul dvs. este gestionat de către administratorul IT, iar caracteristicile pot fi limitate.
Găsiți mai multe actualizări. Utilizați SupportAssist pentru a găsi cele mai recente actualizări ale driverelor pentru dispozitivul dvs.
Dell Technologies recommends reviewing this update to determine if it applies to your system. The update contains changes that impact only certain configurations or provides new features that may or may not apply to your environment.
Format fișierExtrage fișiere direct pe discul local
Nume fișier:perc4di-118c-72c.tar.gz
Dimensiune fișier:538.62 KB
Acesta este un fișier mare. În funcție de viteza conexiunii, descărcarea poate dura mai mult timp.
Descriere format:
This file format consists of an archive of files that may be decompressed to a directory on the hard drive. The installation can then be done from that directory.
Instructions for downloading and creating driver diskette: ----------------------------------------------------------
You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
Download the file PERC4di-118c-72c.tar.gz to a temporary directory on your working system.
Extract the file to the floppy disk as follows:
1. On a Linux system:
Type the following commands under a Linux command shell: mount /dev/fd0 /mnt/floppy tar xvzf -C /mnt/floppy (Eg: /temp/PERC4di-118c-72c.tar.gz) umount /mnt/floppy
2. On a Microsoft Windows system:
You can use Winzip to extract tar.gz archives. However, note the following settings under Winzip to ensure correct extraction of the files.
Start Winzip -> Go to Options -> Configuration
Under the Miscellaneous tab make sure "TAR file smart CR/LF conversion" is unchecked.
Upon opening the tar.gz archive with Winzip, you get the following prompt:
'Archive contains one file. Should Winzip decompress it to a temporary folder and open it?'
Press 'yes' and extract the files normally under Winzip to the floppy drive.
Install Red Hat Linux 7.2 driver for PERC 4/Di as a boot controller -------------------------------------------------------
There are two ways of installing Red Hat 7.2 driver onto the PERC 4/Di as a boot controller. One is using a driver disk during OS installation and the second is using a driver (megaraid) RPM to update driver after OS is installed. The steps for both of these methods are provided below. All the files needed for both methods are included in the driver diskette created above.
For more detailed installation instructions of Red Hat 7.2, please refer to the OS installation guide at http://www.dell.com/linux.
I. Installing driver during OS installation: --------------------------------------------
1. Boot normally from the Redhat installation CD-Rom.
2. Type 'linux dd' on the boot prompt.
3. When the install prompts for a driver disk, insert the driver diskette created above and press 'Enter'.
4. Installation progresses normally. Continue until the 'Create Bootdisk' screen. Press CTRL-ALT-F2 to get to a shell window and type the following commands:
chroot /mnt/sysimage cd /boot /sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10 lilo ( only if lilo was used as bootloader. If grub used - skip this step ) exit
Press CTRL-ALT-F7 to get back to the install screen.
5. Complete the installation as directed by the install.
II. Update driver using RPMs after OS is installed --------------------------------------------------
Type the following commands under a Linux command shell:
mount /dev/fd0 /mnt/floppy cd /mnt/floppy ./megarpmwrapper.sh
Than follow the on-screen instructions to install the RPM driver.
For more detailed information about the script megarpmwrapper.sh, please refer to the release_notes.txt included in the release.