LSI Logic Ultra 320 SCSI Adapter Non-RAID, v.1.9.11.0, A00
INSTALATE AUTOMAT Acest fișier a fost instalat automat ca parte a unei actualizări recente. Dacă întâmpinați orice probleme, puteți descărca și reinstala manual.Conținutul acestei pagini este posibil să fi fost tradus automat. Pentru a furniza feedback, completați formularul din partea de jos a paginii.
LSI Logic PCI SCSI/FC MPI Driver for Windows 2003 v1.9.11.0
Recomandate
Găsiți cea mai bună descărcare pentru sistemul dvs.
Introduceți detaliile produsului pentru a vedea cele mai recente informații despre driverele sistemului dvs.Asistență căutare
Introduceți eticheta de service Dell sau modelul
Doriți să vă căutați produsul? Introduceți un identificator de produs. Arătați-mi cum
This driver is not compatible
This driver is not applicable for the selected product. Choose another product to re-enter your product details for this driver or visit the Product Support page to view all drivers for a different product.
Conectați-vă la Windows ca administrator pentru a utiliza scanarea automată. Dacă sunteți deja conectat ca administrator și vedeți acest mesaj, reporniți sistemul. Sistemul dvs. este gestionat de către administratorul IT, iar caracteristicile pot fi limitate.
Găsiți mai multe actualizări. Utilizați SupportAssist pentru a găsi cele mai recente actualizări ale driverelor pentru dispozitivul dvs.
Fixes & Enhancements
Initial Release
Citiți mai multeVersiune
1.9.11.0, A00
Data lansării:
22 nov. 2007
Tip de descărcare
Driver
Categorie
Dispozitive SCSI non-RAID
Importanță
RecommendedDell Technologies recomandă aplicarea acestei actualizări în următorul ciclu de actualizare programat. Actualizarea conține modificări pentru menținerea stării generale de funcționare a sistemului. Acesta asigură faptul că software-ul sistemului rămâne actual și compatibil cu alte module de sistem (firmware, BIOS, drivere și software) și poate include alte caracteristici noi.
Formate disponibile View Important Information
Format fișier Extrage fișiere direct pe discul local
Nume fișier: MD2K3A00.exe
Dimensiune fișier: 65 KB
Acesta este un fișier mare. În funcție de viteza conexiunii, descărcarea poate dura mai mult timp.
Descriere format:
This file format consists of an archive of files that may be decompressed to a directory on the hard drive. The installation can then be done from that directory.
Pentru a asigura integritatea descărcării, verificați valoarea cifrei de control.
MD5:
Not available
SHA1:
Not available
SHA-256:
Not available
Prin descărcare, acceptați termenii Dell Software License Agreement.
Informații importante
This driver is compatible with LSI 1020/1030 SCSI controllers and is intended for use with Windows 2003 Server, Enterprise Edition Server, Web Server, Small Business Server and Datacenter Server.
Since the 1020/1030 BIOS/FW is delivered as part of the System BIOS, it is highly recommended that you have the latest available System BIOS (also available from Dell support) already installed on your system before updating this driver
Since the 1020/1030 BIOS/FW is delivered as part of the System BIOS, it is highly recommended that you have the latest available System BIOS (also available from Dell support) already installed on your system before updating this driver
Sisteme de operare acceptate
Windows Server 2003
Se aplică pentru
Ultra 320 SCSI Adapter Non-RAID
Instrucțiuni de instalare
Custom Instructions for MD2K3A00.exe:
Download
1. Click Download Now, to download the file.
2. If the Export Compliance Disclaimer window appears, click Yes, I Accept this Agreement.
3. When the File Download window appears, click Save and click OK. The Save In: window appears.
4. From the Save In: field, click the down arrow then click to select Desktop and click Save. The file will download to your desktop.
5. If the Download Complete window appears, click Close. The file icon appears on your desktop.
Diskette Creation
1. Insert a floppy diskette into the floppy drive.
2. Double-click the new icon on the desktop. The Self-Extractor window appears.
3. Specify the floppy drive as the location to unzip the files.
4. Click on the unzip button to extract files.
IMPORTANT NOTE: If you are running Open Manage Array Manager v3.2 or higher under Windows 2003, to avoid a potential Blue Screen, prior to updating the driver you will need to:
1. Disable the SCSI subsystem provider in the Array Manager Utilities before upgrading the driver. Please refer to the Array Manager documentation for details on how to do this.
2. Once the SCSI provider is disabled, you should then navigate to the \WINDOWS\SYSTEM32\DRIVERS folder and temporarily rename ASPI32.SYS to ASPI32.XXX, then reboot the system before proceeding with the upgrade.
3. Following the upgrade, you will need to reboot again before re-naming ASPI32.SYS back to its' original name, then finally re-enabling the SCSI provider.
Updating the driver on an Existing Windows 2003 Server
*NOTE: You must be logged on as Administrator or have administrative privileges to perform these steps:
1. Copy files extracted above to formatted floppy disk
2. From the desktop, right-click the My Computer icon.
3. Left-click Manage.
4. Click Device Manager.
5. Double-click SCSI and RAID controllers (A List of all currently installed SCSI controllers appears) - in the case of a dual channel controller, there will be two devices listed (one for each channel).The driver will have to be updated separately for each channel.
6. Double-click the appropriate SCSI controller (such as 'LSI Logic 1020/1030 Ultra320 SCSI Adapter').
7. Select the Driver tab.
8. Select Update Driver. (The Hardware Update Wizard appears).
9. Choose 'Install from a list of specific locations" and click Next.
10. Choose 'Don't Search. I will choose the driver to install"
11. Click Next.
12. Click 'Have Disk' button. (The 'Install from Disk' dialog appears).
13. Insert the driver diskette created above. (Skip this step if installing driver from location on hard drive)
14. Click 'Browse' button (Locate File dialog appears).
15. Use pull-down box to find floppy drive or location on hard drive where you previously extracted files.
16. Once the correct path appears in the dropdown box, 'symmpi.inf' should appear in 'File Name' box - if not, select it.
17. Click 'Open' button ('Install From Disk' dialog reappears with correct path displayed).
18. Click 'OK' (Upgrade Device Driver Wizard reappears).
19. Choose 'LSI Logic 1020/1030 Ultra320 SCSI Adapter'
20. Click 'Next'
21. Click 'Next' again to confirm choice and upgrade driver
22. Close Wizard by clicking Finish
23. Close Properties Dialog for device.
24. Do not reboot system yet if prompted to do so.
25. Repeat steps 5-23 for second channel after Device Manager refreshes.
26. Reboot System to complete upgrade.
Adding the LSI Logic SCSI Driver to an Existing Windows 2003 Server (non-upgrade) - *NOTE* this will only apply if the SCSI controller was previously disabled in system BIOS setup, and you have enabled it for the first time - otherwise, follow the update instructions above:
1) Boot the system to Windows 2003. The 'Found New Hardware' Wizard displays.
2) Select 'Search for a suitable driver' and select 'Next' to continue.
3) Select 'Floppy disk drive', insert the LSI Logic Windows 2003 SCSI driver disket
Download
1. Click Download Now, to download the file.
2. If the Export Compliance Disclaimer window appears, click Yes, I Accept this Agreement.
3. When the File Download window appears, click Save and click OK. The Save In: window appears.
4. From the Save In: field, click the down arrow then click to select Desktop and click Save. The file will download to your desktop.
5. If the Download Complete window appears, click Close. The file icon appears on your desktop.
Diskette Creation
1. Insert a floppy diskette into the floppy drive.
2. Double-click the new icon on the desktop. The Self-Extractor window appears.
3. Specify the floppy drive as the location to unzip the files.
4. Click on the unzip button to extract files.
IMPORTANT NOTE: If you are running Open Manage Array Manager v3.2 or higher under Windows 2003, to avoid a potential Blue Screen, prior to updating the driver you will need to:
1. Disable the SCSI subsystem provider in the Array Manager Utilities before upgrading the driver. Please refer to the Array Manager documentation for details on how to do this.
2. Once the SCSI provider is disabled, you should then navigate to the \WINDOWS\SYSTEM32\DRIVERS folder and temporarily rename ASPI32.SYS to ASPI32.XXX, then reboot the system before proceeding with the upgrade.
3. Following the upgrade, you will need to reboot again before re-naming ASPI32.SYS back to its' original name, then finally re-enabling the SCSI provider.
Updating the driver on an Existing Windows 2003 Server
*NOTE: You must be logged on as Administrator or have administrative privileges to perform these steps:
1. Copy files extracted above to formatted floppy disk
2. From the desktop, right-click the My Computer icon.
3. Left-click Manage.
4. Click Device Manager.
5. Double-click SCSI and RAID controllers (A List of all currently installed SCSI controllers appears) - in the case of a dual channel controller, there will be two devices listed (one for each channel).The driver will have to be updated separately for each channel.
6. Double-click the appropriate SCSI controller (such as 'LSI Logic 1020/1030 Ultra320 SCSI Adapter').
7. Select the Driver tab.
8. Select Update Driver. (The Hardware Update Wizard appears).
9. Choose 'Install from a list of specific locations" and click Next.
10. Choose 'Don't Search. I will choose the driver to install"
11. Click Next.
12. Click 'Have Disk' button. (The 'Install from Disk' dialog appears).
13. Insert the driver diskette created above. (Skip this step if installing driver from location on hard drive)
14. Click 'Browse' button (Locate File dialog appears).
15. Use pull-down box to find floppy drive or location on hard drive where you previously extracted files.
16. Once the correct path appears in the dropdown box, 'symmpi.inf' should appear in 'File Name' box - if not, select it.
17. Click 'Open' button ('Install From Disk' dialog reappears with correct path displayed).
18. Click 'OK' (Upgrade Device Driver Wizard reappears).
19. Choose 'LSI Logic 1020/1030 Ultra320 SCSI Adapter'
20. Click 'Next'
21. Click 'Next' again to confirm choice and upgrade driver
22. Close Wizard by clicking Finish
23. Close Properties Dialog for device.
24. Do not reboot system yet if prompted to do so.
25. Repeat steps 5-23 for second channel after Device Manager refreshes.
26. Reboot System to complete upgrade.
Adding the LSI Logic SCSI Driver to an Existing Windows 2003 Server (non-upgrade) - *NOTE* this will only apply if the SCSI controller was previously disabled in system BIOS setup, and you have enabled it for the first time - otherwise, follow the update instructions above:
1) Boot the system to Windows 2003. The 'Found New Hardware' Wizard displays.
2) Select 'Search for a suitable driver' and select 'Next' to continue.
3) Select 'Floppy disk drive', insert the LSI Logic Windows 2003 SCSI driver disket
Ajutor și tutoriale pentru drivere
Pentru mai multe descărcări, accesați Drivere și descărcări. Pentru ajutor privind utilizarea informațiilor de pe această pagină, accesați Tutoriale și ajutor pentru drivere.