LSI Logic PERC 4/Di, v.1.18c, A03

АВТОМАТИЧЕСКАЯ УСТАНОВКА Этот файл был автоматически установлен в рамках недавнего обновления. При возникновении каких-либо проблем этот файл можно вручную загрузить и переустановить.
Содержимое этой страницы могло быть автоматически переведено. Чтобы оставить отзыв, заполните форму в нижней части страницы.
PERC 4/Di Device Driver for Red Hat Linux 7.2.
Рекомендуется

Найдите наиболее подходящий файл для вашей системы

Введите сведения о вашем продукте, чтобы просмотреть актуальную информацию о драйверах для вашей системы

Поиск по поддержке

Введите сервисный код или модель Dell

Хотите найти свой продукт? Введите идентификатор продукта. Показать как

Этот драйвер несовместим

Этот драйвер неприменим к выбранному продукту. Выберите другой продукт, чтобы повторно ввести сведения для данного драйвера, или посетите страницу поддержки продукта, чтобы просмотреть все драйверы для другого продукта.

Дополнительные обновления. Используйте SupportAssist для поиска всех последних обновлений драйверов для вашего устройства.

Исправления и улучшения

Not Applicable
Развернуть

Версия

1.18c, A03

Дата выпуска

13 Aug 2002

Тип загрузки

Драйвер

Категория

SCSI RAID

Важность

Опционально
Dell Technologies рекомендует ознакомиться с этим обновлением, чтобы определить, применимо ли оно к вашей системе. Данное обновление содержит изменения, которые действуют только в определенных конфигурациях, или новые функции, которые могут не подходить для существующей среды.
Доступные форматы

Формат файла: Извлечение файлов напрямую на локальный диск
Имя файла: perc4di-118c-72c.tar.gz
Размер файла: 538.62 KB
Это большой файл. В зависимости от скорости подключения скачивание может занять некоторое время.
Описание формата:
Этот формат файла состоит из архивных файлов, которые могут быть распакованы в каталог на жестком диске. Установка может быть выполнена из этого каталога.
Чтобы убедиться в целостности скачанного файла, проверьте значение его контрольной суммы.
MD5:
Отсутствует
SHA1:
Отсутствует
SHA-256:
Отсутствует

Загружая файл, вы принимаете условия лицензионного соглашения об использовании программного обеспечения Dell. (на английском языке)

Дополнительные сведения

Показать все | Скрыть все
Instructions for downloading and creating driver diskette:
----------------------------------------------------------

You will need a formatted 3 1/2 inch floppy diskette for the following procedure.

Download the file PERC4di-118c-72c.tar.gz to a temporary directory on your working system.

Extract the file to the floppy disk as follows:

1. On a Linux system:

Type the following commands under a Linux command shell:
mount /dev/fd0 /mnt/floppy
tar xvzf -C /mnt/floppy
(Eg: /temp/PERC4di-118c-72c.tar.gz)
umount /mnt/floppy

2. On a Microsoft Windows system:

You can use Winzip to extract tar.gz archives. However,
note the following settings under Winzip to ensure correct
extraction of the files.

Start Winzip -> Go to Options -> Configuration

Under the Miscellaneous tab make sure "TAR file smart
CR/LF conversion" is unchecked.

Upon opening the tar.gz archive with Winzip, you get the
following prompt:

'Archive contains one file. Should Winzip decompress it to
a temporary folder and open it?'

Press 'yes' and extract the files normally under Winzip to
the floppy drive.



Install Red Hat Linux 7.2 driver for PERC 4/Di as a boot controller
-------------------------------------------------------

There are two ways of installing Red Hat 7.2 driver onto the
PERC 4/Di as a boot controller. One is using a driver disk during
OS installation and the second is using a driver (megaraid) RPM to update
driver after OS is installed. The steps for both of these methods are
provided below. All the files needed for both methods are included in the
driver diskette created above.

For more detailed installation instructions of Red Hat 7.2, please refer
to the OS installation guide at http://www.dell.com/linux.


I. Installing driver during OS installation:
--------------------------------------------

1. Boot normally from the Redhat installation CD-Rom.

2. Type 'linux dd' on the boot prompt.

3. When the install prompts for a driver disk, insert the
driver diskette created above and press 'Enter'.

4. Installation progresses normally. Continue until the
'Create Bootdisk' screen. Press CTRL-ALT-F2 to get to a
shell window and type the following commands:

chroot /mnt/sysimage
cd /boot
/sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10
lilo ( only if lilo was used as bootloader. If grub used - skip this step )
exit

Press CTRL-ALT-F7 to get back to the install screen.

5. Complete the installation as directed by the install.


II. Update driver using RPMs after OS is installed
--------------------------------------------------

Type the following commands under a Linux command shell:

mount /dev/fd0 /mnt/floppy
cd /mnt/floppy
./megarpmwrapper.sh

Than follow the on-screen instructions to install the RPM driver.

For more detailed information about the script megarpmwrapper.sh,
please refer to the release_notes.txt included in the release.

Справка и руководства по драйверам