Dell SAS Hard Drive Firmware Utility, SATA Hard Drive Firmware Utility, v.Seagate SAS, A00
AUTOMATISKT INSTALLERADDen här filen installerades automatiskt som en del av en ny uppdatering. Om du har problem kan du ladda ner och installera om den manuellt.
Innehållet på den här sidan kan ha översatts automatiskt. Fyll i formuläret längst ned på sidan för att ge feedback.
Den här filen installerades automatiskt som en del av en ny uppdatering. Om du har problem kan du ladda ner och installera om den manuellt.
Seagate drives not seen during SMTD installation or after adding additional drives online in Linux. This is a special release targeted only for 5 Seagate SAS drives listed in the Fixes and Enhancements section.
R211868 is intended for all other firmware updates.
Rekommenderat
Hitta den bästa nerladdningen för ditt system
Ange din produktinformation för att se den senaste informationen om drivrutiner för ditt system
Sök efter support
Ange din Dell service tag eller modell
Vill du söka efter din produkt? Ange en produktidentifierare.Visa mig hur
Inga resultat hittades. Vi kunde inte hitta något som matchade din sökning. Ändra din sökning och försök igen.
Den här drivrutinen är inte kompatibel
Den här drivrutinen gäller inte för den valda produkten. Välj en annan produkt för att ange din produktinformation för den här drivrutinen igen eller gå till produktsupportsidan för att visa alla drivrutiner för en annan produkt.
Logga in på Windows som administratör för att använda automatisk skanning. Om du redan är inloggad som administratör och ser det här meddelandet ska du starta om.Ditt system hanteras av IT-administratören och funktionerna kan vara begränsade.
Hitta fler uppdateringar. Använd SupportAssist för att hitta alla de senaste drivrutinsuppdateringarna för din enhet.
Korrigeringar och förbättringar
Several Seagate drives shipped from Dell factories between February 2nd and February 20th may experience the following symptoms: A) During an install from System Management Tool and Documentation DVD: 1. If there is no RAID config from ctrl-r and the DVD is booted it will display a blank white screen where there should be array configuration setup. 2. If there is a RAID config from ctrl-r already present on the drives, it will boot to the SMTD DVD but skip the RAID config screen. The menu item for RAID config in the left window will not appear in the action list. Install can be completed using this method.
B) Enclosure or server hard drives are being configured or added in an existing Linux install: The drives my not be seen in the Linux browser that is using Open Manage Storage Management to configure the drives. Or, the Vendor ID for the disk drive may appear with garbled characters.
The FW version on the drive label will represent the correct firmware version; however, a later version was flashed to the drive in the factory.
Dell Technologies rekommenderar att du installerar den här uppdateringen under nästa schemalagda uppdateringscykel. Uppdateringen innehåller ändringar för att bibehålla det allmänna systemtillståndet. Den säkerställer att systemets programvara förblir aktuell och kompatibel med andra systemmoduler (fast programvara, BIOS, drivrutiner och programvara) och kan inkludera andra nya funktioner.
Det här är en stor fil. Beroende på din anslutningshastighet kan det ta lite tid att ladda ner den.
Formatbeskrivning:
Den här filen innehåller en komprimerad (eller zippad) uppsättning filer. Hämta filen till en mapp på hårddisken och kör sedan filen (dubbelklicka på den) för att packa upp filerna. Följ anvisningarna för att slutföra installationen.
This release is intended for use on drives attached to SAS/ PERC controllers and MD1000 Enclosures.
Please note: Only Dell Branded SAS/SCSI and PERC controllers are supported. Embedded SATA controllers are not supported.
On drives attached to PERC5/PERC6 controllers, the first drive to be updated requires a 5 minute delay before firmware flash to begin. Do not power cycle or reboot your system while the update is in progress.
1. Click the "Download Now" link to download the file. 2. When the File Download window appears, click "Save" to save the file to your hard drive.
Installation
1. Browse to the location where you downloaded the file and double-click the new file. 2. Read over the release information presented in the dialog window. 3. Download and install any prerequisites identified in the dialog window before proceeding. 4. Click the Install button. 5. Follow the remaining prompts to perform the update.
1) Click Download now. The File Download window appears.
2) Click the Save button. The Save As window appears.
3) Select Desktop using the drop-down menu to the right of Save in.
4) Click the Save button. A progress meter moves as the download is completed.
5) If necessary, click X in the upper right-hand corner of the Download Progress Window to close it upon completion.
6) Double click the Icon on your desktop for the newly saved file. The Dell Bios Release Notes window appears.